RigExpert TI-5000 Manuel utilisateur
TI-5000 RigExpert®
User’s manual
USB Transceiver
Interface
.
4
6
6
8
10
14
14
16
Introduction
Operating the TI-5000
Front and rear panels
Transceiver and computer connection
Updating the firmware
Annexes
Annex 1: Specifications
Annex 2: Changing audio input and output level
Table of contents
User’s manual
Thank you for purchasing a RigExpert
TI-5000 USB Transceiver Interface! We
did our best to make it powerful yet easy
to use.
RigExpert TI-5000 is a device for
operating phone, CW and digital modes
using personal computer with USB port.
It provides:
• Transceiver audio interface
Analog audio interface is a connection
to transceiver audio output (external
speaker connector or line output) and
transceiver audio input (microphone
connector or line input). Audio interface
enables operating digital modes,
recording and playing voice, as well
as other useful functions (such as
measuring levels of a signal from the air)
by using a computer.
Introduction
Input (main and sub channels) and
output volume levels are adjusted by
potentiometers on the front panel of the
device.
• CAT interface for various transceiver
models
CAT (Computer Aided Transceiver)
system provides control of transceiver
frequency, operating mode and other
functions by computer software. Nor-
mally, modern transceivers have serial
(with various signal levels) link providing
CAT interface.
A separate COM port is created for the
CAT system so the computer software can
communicate to the transceiver.
4
ON CW PTT CAT FSK
Speed Main Sub Mic Out
TI-5000
RigExpert TI-5000
• FSK output
FSK (Frequency Shift Keying) is a popular
method of transmitting digital messages
over radio primarily used in radioteletype
(RTTY) mode. Most transceivers provide
FSK modulator feature to make the RTTY
signal stable and clear.
A separate COM port is created for the
FSK function.
• PTT and CW output functions
Transceivers provide PTT (Push To Talk)
and CW (Continuous Wave) keyer inputs
to allow setting the transmitter on or off
and operating CW using external device
(PTT pedal, CW bug or paddle, terminal
node controller, or personal computer).
A separate COM port is created for PTT/
CW outputs.
•Squelch input
Some software, such as EchoLink,
requires the interface to provide a squelch
input to detect if the radio channel is
busy.
In RigExpert TI-5000, the squelch input is
assigned to the DCD line of the COM port
used for PTT and CW outputs.
• CW keyer
Built-in RigExpert implementation of
WinKey.
WinKey is a Morse keyer that is designed
to attach to a PC’s serial port and provide
accurate transmitter keying from a Win-
dows based ham radio software.
A separate COM port is created for
WinKey.
• Microphone and foot switch inputs
This function enables using the TI-5000
in voice modes. When the foot switch
is pressed, audio from microphone is
immediately transmitted by the rig. In
addition, audio stream is fed into the
computer (via left audio channel) to be
recorded by voice keyer software. Micro-
phone level is adjustable.
5
User’s manual
Front panel:
1. Speed. CW speed pot for the WINKEY
keyer. May be deactivated by software.
2. ON. Lights when the RigExpert TI-
5000 device is plugged in and the drivers
are installed.
3. CW. Shows transmissions in CW mode.
4. PTT. Indicates when the transceiver
transmits.
5. CAT. Monitors CAT data exchange
between transceiver and computer.
6. FSK. Lights when RigExpert TI-5000 is
sending FSK data.
7. Main. Input level, channel 1 (main
receiver audio).
8. Sub. Input level, channel 2 (sub-
receiver audio).
9. Mic. Microphone signal level.
10. Out. Output level (audio to the
transceiver).
Front and rear panels
ON CW PTT CAT FSK
Speed Main Sub Mic
1 2 3 4 5 6 7 8 9
Out
10
TI-5000
Operating the
TI-5000
6
RigExpert TI-5000
Rear panel:
11. MIC1. Microphone input connector
(3.5 mm).
12. MIC2. Microphone input connector
(3.5 mm).
13. FOOTSW. Foot switch, RCA socket.
14. TRANSCEIVER. 25-pin transceiver
connector.
15. PADDLE. CW paddle input (3.5 mm).
16. USB IN. Connect to the computer
USB port.
17. USB OUT. USB hub output to connect
USB devices such as computer mouse.
TRANSCEIVER
PADDLE
USB IN
11 13 14 15 17
MIC1
FOOTSW
16
MIC2USB OUT
12
7
User’s manual
Transceiver and
computer connection
The connection to your transceiver is
made by using a specialized cable. A
specific type of the cable depends on
the manufacturer and the model of the
transceiver.
Please watch the marking to make
sure all plugs are inserted properly to
corresponding sockets located on your
transceiver.
You may either order a transceiver cable with your TI-5000 or assemble it yourself.
See the schematic diagrams on our website, www.rigexpert.com .
A number of analog and digital signals are
routed between your transceiver and Rig-
Expert TI-5000. Cables for most modern
rigs (Icom, Kenwood, Yaesu, Ten-Tec,
Elecraft) are available; future rigs are sup-
ported by design of the universal 25-pin
connector of RigExpert TI-5000.
The squelch connection is not available in all cables manufactured by our company.
The user has to add this connection, if necessary.
8
RigExpert TI-5000
Use a standard USB A-B cable (up to 5
meters long) to connect your RigExpert
TI-5000 to a USB port of your computer.
It is recommended to use USB sockets
located at the back panel of the PC.
Once the cable is connected, computer
detects a new device. No drivers required
for modern operating systems.
More info on www.rigexpert.com/ti-5000.
9
User’s manual
10
Updating the firmware
• Connect your RigExpert TI-5000 to your
computer
Use a standard USB A-B cable (up to 5
meters long) to connect your RigExpert
TI-5000 to a USB port of your computer.
It is recommended to use USB sockets
located at the back panel of the PC.
• Start the RigExpert Flash Tool
You may find Flash Tool at the Downloads section of the website, www.rigexpert.com.
Table des matières
Autres manuels RigExpert Émetteur-récepteur
