Riello GI/EMME 400 Guide de démarrage rapide
2915143 (6)
Installation, use and maintenance instructions
Dual fuel Gas-Oil/Gas burner
MODEL TYPE
GI/EMME 400 496 T80
5143
1
TECHNICAL FEATURES
The burner conforms to IP 40 level of insulation as per CEI/70.1
Thermal power 116/232 ÷ 465 kW - 100.000/200.000 ÷ 400.000 kcal/h
Fuels Oil, max. viscosity at 20°C: 6mm
2
/s (1.5°E) natural gas with
Pci 8600 kcal/m
3
Lpg with Pci 22.200 kcal/m
3
Minimum gas pressure
(measured at the test-point) Maximum capacity requires 9 mbar with natural gas,
9.5 mbar with LPG. Combustion chamber at 0 mbar.
Maximum gas pressure 150 mbar
Electrical supply Three-phase 380 V +10% -15% ~60 Hz with neutral
Motor 1.5 A/380V
Pump-capacitor motor1A / 220 V - 6.3 µF
Ignition transformer Primary: 1.8A / 220 V - Secondary: 30 mA / 1x8 kV
Pump Output 55 kg/h at 12 bar - max pressure 15 bar
OperationTwo stages
Fig. 1
EQUIPMENT
Quantity Burner accessories
1 Gas-train’s gasket
8 Screws
1 Insulating screen
3 Seal
2 Oil hoses
4 Connectors
4 Gaskets
1 Lpg transf. kit
2 Oil nozzles
1 Flange
KEY TO LAY-OUT
1- Oil valve 1° stage
2- Oil valve 2° stage
3- Safety oil valve
4- Oil supply port
5- Oil return port
6- Pressure regulator at the pump
7- Air damper motor
8- Pressure gauge port (G 1/8)
9- Vacuum gauge port (G 1/8)
10 - Terminal board
11 - Reset push-button of the motor
overload relay
12 - Cable gland
13 - UV photocell
14 - Oil motor capacitor
15 - Oil-gas selector switch
16 - Control-box reset button
17 - Air pressure-switch
18 - Gas pressure socket to sleeve
2 1 389 4 5 7 18
17 15 11
10 12
16
1413
S7537
6
5143
2
DIMENSIONS
WORKING RANGE
PRESSURE IN THE COMBUSTION CHAMBER - 2
nd
STAGE OUTPUT
MINIMUM GAS PRESSURE - 2
nd
STAGE OUTPUT
Pressure
: measured at the test point with combustion chamber at 0 mbar.
Boiler front-plate
drilling
* Extension that you can obtain with special extended head (to be requested separately)
.
Burner
160
160
155 M10
410 610
187
*320
397
97
292
165
Rp 1 1/2
D1785
S7564
S7565
ø 150
Kcal/h
mbar
kW
Min output at 1st stage 116kW - 10Kg/h
S7590
Kcal/h
mbar
kW
Gas pressure test point
Natural gas
LPG S7536
S7591
5143
3
FIXING TO THE BOILER
GAS SUPPLY LINE
In order to devide the combustion head from the rest of the burner, you have to:
- remove the connection (1) from the two valves;
- remove the 4 screws (2 - 3);
- slide the burner body (A) along the rails (4);
- mount the group (B) to the boiler’s plate (6) interposing gasket (5).
Mount the group (A) to the boiler front. Fit the nozzles and regulate the combustion head (as speci-
fied below).
S7539
654132
BA
{
{
1- Gas supply pipe 7- Min. gas pressure switch
2- Manual valve 8- Gas safety shut off valve
3- Isolator joint 9- 1° stage gas shut off valve
4- Filter 10 - 2° stage gas shut off valve
5- Pressure governor 11 - Burner
6- Pressure test-point 12 - Gas leak control device
S7572
6
986
7
54
6
32 1
11
10
12
5143
4
OIL SUPPLY
S7542
S7541
Please note:
all oil lines must be airtight.
We suggest copper-piping. Level as the suction
pipe, then a none return valve is not required
and the section-pipe can be disconnected with-
out causing any problems.
H= Margin; L= Inlet-pipe’s length, including the vertical line.
The copper pipes with diameter 8 and 10, shown in the schemes, can be replaced with 1/4 and 3/8
steel pipes, commercial gas without welding.
HLm
m Øi 8 Øi 10
0.5 5 10
11020
1.5 15 30
22040
HLm
m Øi 8 Øi 10
03270
0.5 28 62
12455
1.5 20 48
21640
3725
3.5 – 10
H
max. 4m
H
max. 4m
H
5143
5
BURNER ELECTRICAL WIRING
(carried out in the factory)
KEY TO LAY-OUT
C: Pump motor capacitor
CMV: Contact-maker
CO: Selector switch
MB: Burner terminal strip
MP: Pump motor
MV: Fan motor
PA: Air pressure switch
RT: Thermal relay
SM: Servo-motor
TA: Ignition transformer
TB: Burner earth
UV: Probe U.V.
V1: 1° stage valve
V2: 2° stage valve
VS: Oil safety valve
SELECTOR SWITCH
OIL O GAS
3 - 4
5 - 6
7 - 8
9 - 10
11 - 12
13 - 14
15 - 16
S7573
S7562
5143
6
ELECTRICAL CONNECTIONS TO THE WIRING TERMINAL BLOCK
(to be carried out by the installer)
KEY TO LAYOUT
MB - Burner terminal strip V1 - 1° stage gas shut off valve
MR - Gas train terminal strip V2 - 2° stage gas shut off valve
TS - Safety remote control system VS - Gas safety shut off valve
TL - Limit control system S- Remote lock signal
T2 - 2° stage remote control system PC - Check pressure switch
PG - Min. gas pressure switch TB - Burner earth
NOTICE
- The electric wiring carried out by the installer must be in compliance with the rules in force in the
country.
- Leads minimal section 1.5 mm2.
- Burners with non-stop operation: for safety reasons, this type of burner must be stopped every 24
hours of operation, by means of an hours-counter to be connected in series with the adjustment
devices.
- The flame modulation in obtainable trought the 2° stage remote control system (T2).
Connected to the terminals 9-10.
S7574
5143 7
FIXING OF THE ELECTRICAL WIRES
All the electrical wires, which are to be connected into the terminal rail 10 (fig. 1) should pass through
the cable glands hubes 12 (fig. 1), accordingly the scheme below.
1- Supply : gland Pg 21
2- Regulation thermostat : gland Pg 13.5
3- Safety thermostat : gland Pg 13.5
4 - 2° stage thermostat : gland Pg 13.5
5- GAS TRAIN : gland Pg 13.5 - for sheath ø 13
To guarantee the IP 40 protection level, in accordance to CEI 70.1, seal the glands that are not used.
NOTES
- Do not exchange “Neutral” with “Phase” (avoid a plug/socket connection).
- Make a good earth connection.
Verify that the burner will lockout by firing the burner and obscuring the UV cell.
ATTENTION
When you close the burner on the two guide rail, all the slack should be pulled out the high voltage-
cable.
This burner is in accordance to the CEE law n.76/889, D.M. 9/10/1980, for protection against radio-
noises.
S7575
5143 8
COMBUSTION HEAD ADJUSTMENT
Adjustments can be made to the burner, when it is still open for installation (see page 3, fixing to
the boiler).
SETTING OF GAS DISTRIBUTOR
The burner leaves the factory setted for burning natural
gas (see the drawing on the right):
-Each hole (F) completely opened.
To burn LPG fit the kit as detailed below:
-Fit 6 nozzles with ø 3 mm on outlets to holes (F).
Nozzle
1° 2° 1°+2°
kg/h
bar GPH kg/h GPH kg/h
12 2.50 9.7 2.50 9.7 19.4
10
12 3.00
3.00 10.8
11.7 3.00
3.00 10.8
11.7 21.6
23.4
10
12 3.50
3.50 12.6
14.0 3.50
3.50 12.6
14.0 25.2
28.0
10
12 4.00
4.00 14.3
15.8 4.00
4.00 14.3
15.8 28.6
31.6
10
12 4.50
4.50 16.4
18.0 4.50
4.50 16.4
18.0 32.8
36.0
10
12 5.00
5.00 18.2
20.4 5.00
5.00 18.2
20.4 36.4
40.8
10 5.50 19.7 5.50 19.7 39.4
Pump
pressure
NOZZLE’S CHOICE
Spray angle:
- usually, 60°
- for narrow combustion chambers: 45°
S7546
S7576
Position of the ignition electrodes
4 mm
4 mm
F
1° stage nozzle 2° stage nozzle
Autres manuels pour GI/EMME 400
1
Table des matières
Autres manuels Riello Brûleur
Riello
Riello N10 Guide de démarrage rapide
Riello
Riello RS 28/1 Guide de démarrage rapide
Riello
Riello 40 GS20 TL Guide de démarrage rapide
Riello
Riello RS 28 Guide de démarrage rapide
Riello
Riello RX 70 S/PV Guide de démarrage rapide
Riello
Riello RG3D L Guide de démarrage rapide
Riello
Riello 40 FSP10 Guide de démarrage rapide
Riello
Riello P200 T/N Guide de démarrage rapide
Riello
Riello DB3 SM C03 Guide de démarrage rapide
Riello
Riello RS 34/M MZ Manuel utilisateur
Riello
Riello RLS 1000/M MX Guide de démarrage rapide
Riello
Riello RS 310/E O2 ULX Guide de démarrage rapide
Riello
Riello RDB2.2 54 BF MISTRAL Guide de démarrage rapide
Riello
Riello FS5 Guide de démarrage rapide
Riello
Riello PRESS 200 T/N Guide de démarrage rapide
Riello
Riello RDB 2.2 BF GREENSTAR DANESMOOR 12/18 Guide de démarrage rapide
Riello
Riello RS 70/EV Guide de démarrage rapide
Riello
Riello F15 Guide de démarrage rapide
Riello
Riello RG4F Guide de démarrage rapide
Riello
Riello C9337401 Guide de démarrage rapide
Manuels Brûleur populaires d'autres marques
True Induction
True Induction TI4B Manuel utilisateur
Weishaupt
Weishaupt WG20 Series Manuel utilisateur
Carolina Cooker
Carolina Cooker M116672 Manuel utilisateur
Unigas
Unigas HTP2000 Manuel utilisateur
baltur
baltur BT 250 DSG 4T Manuel utilisateur
muenkel design
muenkel design round burner Manuel utilisateur
