Reprint Mantis Mode d’emploi

Reprint Mantis

Stencil Printer

Version 1.1

release date: 15.11.2010

Reprint Mantis Version: 1.1 15.11.2010 Page

2 of 65

Reprint Limited. Unit 10 Enterprise Park, Piddlehinton, Dorset. United Kingdom

You have opted for Reprint®equipment. We thank you for this decision.

Your device was manufactured according highest quality standards and was tested thoroughly before shipment. It is

very easy in operation; nevertheless we suggest that you read this manual before operating the machine. If you have any

additional questions to your equipment, please don't hesitate to contact:

Reprint Limited

Unit 10, Enterprise Park, Piddlehinton,

Dorset.

United Kingdom

Tel. +44 (0)1305 849254

Fax. +44 (0)1305 849289

Email [email protected].uk

Web www.reprintservices.co.uk

or your nearest authorized Reprint Ltd distributor:

For product information on reflow systems, screen-/ stencil printers, dispensing or manual/semiautomatic or fully

automatic pick and place systems please contact us or visit our webpage:

Reprint Mantis Version: 1.1 15.11.2010 Page

3 of 65

www.reprintservices.co.uk

INDEX

CE-DECLARATION OF CONFORMITY ................................................................... 5

1. Safety Information ......................................................................................... 7

1.1. General ...............................................................................................................................7

1.2. Warning Notices ...................................................................................................................7 1.3. Notice

.................................................................................................................................7

2. Installation ................................................................................................... 9 3. Getting

Started ............................................................................................. 9

3.1. Preparing to Switch On .......................................................................................................... 9

3.2. Switching On ....................................................................................................................... 9 3.3. Logging On

........................................................................................................................ 10 3.4. System Power

..................................................................................................................... 10 3.5. Initialising the Printer

........................................................................................................... 11

3.6. Main Window Layout ........................................................................................................... 12 3.7. Closing Down

the MANTIS ................................................................................................... 13 4. Setting Up a Product File

.............................................................................. 14

4.1. Introduction ....................................................................................................................... 14 4.2. Create a New

Product ........................................................................................................... 14 4.3. Product Information

............................................................................................................. 15

4.4. Product Details ................................................................................................................... 15

4.5. PCB Dimensions .................................................................................................................. 15 4.6. Fiducials

............................................................................................................................ 15 4.7. Board Stop Position

.............................................................................................................. 16

4.8. Enable Soft Stop Option ........................................................................................................ 16

4.9. Set Conveyor / Tooling / Additional Data ................................................................................ 16

4.10. Setting Print Parameters ....................................................................................................... 21 4.11. Setting

up the Vision System .................................................................................................. 24

4.12. Board to stencil Calibration .................................................................................................... 31 4.13. Stencil

Clean Profile ............................................................................................................. 32

5. IS1 2D Paste and stencil inspection ................................................................ 35

5.1. Specifications ...................................................................................................................... 35 5.2. Preparing a New

Product for 2D Inspection ............................................................................... 35 5.3. Creating New Inspection Sites

................................................................................................ 36

5.4. Global Settings .................................................................................................................... 39

5.5. Inspection Actions ............................................................................................................... 41

5.6. Log Files............................................................................................................................ 42

5.7. Advanced ........................................................................................................................... 43

5.8. Inspection in Production........................................................................................................ 44

Reprint Mantis Version: 1.1 15.11.2010 Page

4 of 65

5.9. Running Production ............................................................................................................. 45 6.

Production ................................................................................................. 47

6.1. Product Details ................................................................................................................... 47

6.2. Counters ............................................................................................................................ 47 6.3. Utilities

............................................................................................................................. 48

7. Setting Up the MANTIS (Machine Set-up) ...................................................... 49

7.1. Introduction ...................................................................................................................... 49

7.2. Machine Set-up .................................................................................................................. 49 7.3. Product

Transfer ................................................................................................................ 49

7.4. Beacon ...............................................................................................................................50

7.5. Language Options ................................................................................................................ 51 7.6. Under

Stencil Cleaner Set-up .................................................................................................. 51

8. Working with Product Files (File Manager)..................................................... 53

8.1. Introduction ....................................................................................................................... 53 8.2. Load, Delete

and Copy Product Files ........................................................................................ 53 8.3. Log On Users

..................................................................................................................... 54

8.4. Backup Product Files ............................................................................................................56

8.5. Restore Product Files ...........................................................................................................56 9.

Maintenance / Services ................................................................................ 58

9.1. Under Stencil Cleaner ........................................................................................................... 58 9.2. Machine

Diagnostics ............................................................................................................ 58

9.3. Updating Microcontroller Firmware .................................................... Error! Bookmark not defined. 9.4. Routine

Maintenance ........................................................................................................... 60 10. Printing Basics

............................................................................................. 61

10.1. Working with Solder Paste, Squeegees and Stencils ..................................................................... 61 11.

Working with Solder Paste ........................................................................... 62

11.1. Choosing the right solder paste .............................................................................................. 62 11.2. Paste grade

........................................................................................................................ 62 11.3. Stencil thickness and aperture

................................................................................................ 62 11.4. The Three-Ball Rule

............................................................................................................ 62 11.5. Understanding Viscosity

....................................................................................................... 63 11.6. Working with Stencils

..........................................................................................................65 11.7. Stencil types

.......................................................................................................................65 11.8. Stencil Design

.....................................................................................................................65 11.9. Stencil cleaning

.................................................................................................................. 66

11.10. Working with Squeegees ...................................................................................................... 67

11.11. Squeegee types ................................................................................................................... 67 11.12. Squeegee

pressure and print speed .......................................................................................... 67

Reprint Mantis Version: 1.1 15.11.2010 Page

5 of 65

CE-DECLARATION OF CONFORMITY

Machine SR: 98/37/CE

Directions of low voltage: 73/23/EWG

Directions of electro magnetic compatibility: 89/336/EWG

Manufacturer REPRINT LIMITED

Address of Manufacturer Reprint Limited

Unit 10, Enterprise Park

Piddlehinton

Dorset

We herewith declare, that the mentioned machines are in conformity with the above stated

standards and healthy and safety rules of the CE directives.

If there are any changes on the machine as also on their options by the user/customer, this declaration will expire

immediately.

Typ: Mantis

Serial number:

Date of manufacture:

Applied/used harmonised european

norms:

DIN EN 292-1, 292-2, 294, 954-1,

EN50081-1, EN50082-1, EN61000-3-2,

EN62000-4-2, EN61000-4-2, EN60204

REPRINT LIMITED

Reprint Mantis Version: 1.1 15.11.2010 Page

6 of 65

Piddlehinton, _______________ Martin A. Ziehbrunner

Director

Reprint Mantis Version: 1.1 15.11.2010 Page

7 of 65

1. Safety Information

1.1. General

Always observe the safety rules of the workplace in which you are working.

Ensure you know the location of the Emergency Stop button. When activated, all movement of

the machine stops.

Take appropriate action to ensure loose clothing, jewellery, hair or similar items do not come

into close contact with moving parts.

Never insert your hand or any other part of the body into the machine while it is in operation.

Observe all health and safety regulations when handling solvents used for machine and/or

stencil cleaning. Do not smoke. If in doubt, seek advice.

ISOLATE THE MACHINE BY REMOVING ELECTRICAL POWER AND COMPRESSED

AIR FEEDS BEFORE ATTEMPTING ANY MAINTENANCE OR REPAIR.

The metal foil clamps that hold the board in place when printing are sharp and could cause

injury if touched.

If the machine is used in-line, the responsibility for guarding the feed-in and feed-out conveyor areas

passes to the customer.

1.2. Warning Notices

Warning notices indicate to operators/maintainers possible hazards that may cause lose of life, serious

injury or ill health. An example is given below:

Black-on-yellow warning labels identical to the symbol above are place on the machine alerting the

operator/maintainer to possible hazards that may cause physical injury or equipment damage.

1.3. Notice

Reprint AG shall not be liable for errors contained within this document or for incidental consequential

damages in connection with the furnishing, performance or use of this material.

Reprint Mantis Version: 1.1 15.11.2010 Page

8 of 65

No part of this document may be reproduced, transmitted in any form or means, electronically or

mechanically, including photocopying and recording, for any purpose without the express permission of

Reprint AG.

The information contained within this document is subject to change without prior notice.

Reprint Mantis Version: 1.1 15.11.2010 Page

9 of 65

2. Installation

1. Move the machine to its final position. Take a spirit level and adjust the feet until the machine is

leveled in X and Y.

2. Remove all the transport locks

3. Getting Started

3.1. Preparing to Switch On

Follow the unpacking and installation instructions as described in the ‘Printer Installation’ document.

All power, air and FMI (Foreign Machine Interface) connectors are located at the rear of the machine.

Before applying mains power to the machine, observe the following: -

Ensure the Mains Isolator Switch is in the ‘0’/Off position. The red circular switch can be

found by lifting open the front cover of printer and observed to the front and left of this

area.

Confirm the electricity supply to the printer is in the range specified on the label above the

mains input socket.

The mains cable supplied or a suitable alternative cable is correctly and securely connected to

the printer mains inlet connector.

A clean air supply of between 4 to 6 bar is required to operate certain printer options.

Connect the air supply to the printer. Pipe sizes of 8-10mm outside diameter can be used. Other

sizes will require adaptors.

If the printer is to be used in-line, ensure the correct FMI connectors are connected correctly

and securely.

3.2. Switching On

To successfully power up and initialise the machine, follow these simple steps: -

Lift the front cover and switch the Mains Isolator switch to the ‘1’/On position. Close the cover.

After a few moments the computer monitor should energise and the Windows operating program start to

load.

Once Windows has finished loading, the MANTIS User Interface (UI) program should automatically

start.

If it does not start automatically, double click the MANTIS UI shortcut icon on the Windows desktop.

After an initial introduction screen, the Log On User dialog screen will appear.

If the Log On User dialog screen does not appear within a reasonable time period, check the following: -

Reprint Mantis Version: 1.1 15.11.2010 Page

10 of 65

Is the mains cable securely fitted and the mains power live?

Is the switch of the computer turned on?

Is the switch of the monitor turned on?

Are all connectors to the monitor and keyboard correctly connected?

Are the brightness and contrast controls of the monitor correctly set?

3.3. Logging On

Each operator is required to have a unique User Name and

Password. If your User Name is not shown, click on the

down-arrow to display the complete list of available names.

If you do not have a user name, contact your supervisor who

can generate a new entry for you otherwise click on your

user name.

Now click in the Password box and type in your password.

Click ‘OK’ to continue. If the password entered was

incorrect, you will be prompted to try again.

After successfully logging on, if there are any messages assigned for your attention, then they will be

displayed now.

The last product file used by the printer will now be loaded and become the machine’s current working

file.

3.4. System Power

If you are the first to sign in from machine switch on then the System

Power dialog form will be displayed. System Power applies power to

all machine motors though the motors will not move at this stage.

To turn on System Power, either click on the green button on this form

or press the ‘System Power’ button located on the right hand side of

the front of the machine. Pressing ‘Cancel’ will close this form without

applying the power.

You will now be asked if you wish to initialise the machine.

Selecting ‘Yes’ will automatically take you to the Initialisation form. Selecting ‘No’ will take you

straight to the Main Menu.

3.5. Initialising the Printer

Table des matières

Manuels Imprimante populaires d'autres marques

Lexmark

Lexmark 1400 Series Manuel

Canon

Canon i70 Series Manuel utilisateur

Evolis

Evolis Elypso Manuel utilisateur

Kyocera

Kyocera FS-9530DN Manuel utilisateur

Canon

Canon LASER SHOT LBP-1210 Manuel utilisateur

Samsung

Samsung BIXOLON SRP-350plusF Manuel utilisateur

Canon

Canon PIXMA PRO-1 Series Manuel utilisateur

Canon

Canon PIXMA G3560 Guide de configuration

Dell

Dell Color Laser Printer 2130cn Manuel utilisateur

Tektronix

Tektronix Phaser 840 Manuel utilisateur

Epson

Epson ET-7750 Mode d'emploi

Canon

Canon CLBR 460ps Manuel utilisateur

Eltron

Eltron P210 Guide Manuel utilisateur

Ricoh

Ricoh MD-P1 Manuel utilisateur

Epson

Epson SC-F7100 series Manuel utilisateur

Epson

Epson Stylus C40UX Manuel utilisateur

Canon

Canon imagePASS-A2 Manuel utilisateur

Canon

Canon S820D Manuel utilisateur