Repotec RP-ISF800 Manuel utilisateur

User Manual

Industrial Fast Ethernet 8 port Ethernet Switch, Power input 12-56VDC, -40°C to 75°C

FCC MARKING

This Equipment has been tested and found to comply with the limits for

a Class A digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio

communications.

Operation of this equipment in a residential area is likely to cause

harmful interference in which case the user will be required to correct

the interference at his own expense.

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received;

including interference that may cause undesired operation.

CE MARKING

This equipment complies with the requirements relating to

electromagnetic compatibility, EN 55022 class A for ITE, the essential

protection requirement of Council Directive 2004/108/EC on the

approximation of the laws of the Member States relating to

electromagnetic compatibility.

Company has an on-going policy of upgrading its products and it may

be possible that information in this document is not up -to-date. Please

check with your local distributors for the latest information. No part of

this document can be copied or reproduced in any form without written

consent from the company.

Trademarks:

All trade names and trademarks are the properties of their

respective companies.

Power connection

This industrial Fast Ethernet switch comes with a 6 pin terminal block. It can be operated from 12-56VDC

power source. Always Make sure your input voltage is within this supported voltage range for each model.

WARNING –any exceeded input voltage will not make this unit function and may damage this unit.

To make power connection –Follow the printed polarity for V1+, V1-,

V2+, V2-, and ground. Connect positive wire to V+ , connect negative

wire to V-, also connect neutral wire to the ground screw as shown .

Relay -- You may use 24V@1A relay connection to your external device

for special purpose. When 2 powers are connected, the relay is in

OPEN mode. When any power source fails, the relay change to SHORT

status.

Power connecting procedure:

STEP 1 –Pull out 6 pin terminal block.

STEP 2 –Connect wire to V1+, V1-, or V2+, V2-, and Ground the neutral wire to the ground screw.

STEP 3–Plug back 6 pin terminal block to its place.

WARNING –

Always ground the power source to maintain a clean power input. Due to too many cheap

made power supplies, it creates too much noise, and it will cause the power input fluctuates

when connect to this unit. To avoid this, always ground the power source to gain a clean

power input.

Din Rail Bracket x 1

Wall mount bracket x 2

6 pin Terminal Block x1

Installation package

This unit can be installed by din-rail mounted or wall-mounted. Din-rail brackets and wall-

mounted bracket are included.

PW1

ON -- when V1+, V1- is connected

LED indicator

PW2

ON -- when V2+, V2- is connected

This unit has no POE feature. the POE amber

LED will always stays in OFF status.

Green LED ---

ON =Link

Flash = TX/RX.

Relay LED Amber

ON one power is connected

OFF two powers are connected

Specification:

IEEE Standard

IEEE 802.3 10Base-T Ethernet

IEEE 802.3u 100Base-TX Fast Ethernet

IEEE802.3x Flow Control and Back Pressure

Switch Architecture

Back-plane (Switching Fabric): 1.6Gbps

Data Processing

Store and Forward

Flow Control:

IEEE 802.3x Flow Control and Back Pressure

MAC address Table Size

Packet Buffer Size

Network Connector :

8xRJ-45 10/100BaseT(X) auto negotiation,

Auto MDI/MDI-X function, Full/Half duplex

Network Cable

UTP/STP above Cat.5e Cable

EIA/TIA-568 10-ohm (100m)

Protocol

CSMA/CD

LED

PW1(Power 1) Green,

PW2(Power 2) Green,

SW(relay) Amber,

TX/RJ-45 port:

LNK (Link/Active) Green,

Housing

Heavy Metal Housing

Reserve polarity protection

Present

Overload current protection

Present

Power Supply

Redundant Dual DC 12V-56V Power Input

Power Consumption

3W@48 VDC full load,

Alarm Relay Contact

Relay outputs with current carrying capacity of 1 A

@24VDC,

Relay in short circuit mode when 2 powers are

connected. in open circuit mode when only one

power supply is connected

POE power

n/a

Removable Terminal Block

Provide 2 Redundant power , Alarm relay contact ,6

Wire range: 0.34mm^2 to 2.5mm^2

Solid wire (AWG):12-24/14-22

Stranded wire(AWG): 12-24/14-22

Torque:5lb-In/0.5Nm/0.56Nm

Wire Strip length: 7-8mm

Operating Temperature

-40℃~75℃fully tested.

Operating Humidity

5% to 95% (Non-condensing)

Storage Temperature

-40℃~85℃

MTBF (mean time between

failure)

510,304 hrs ( MIL-HDBK-217F) at 25°C

Housing

Rugged Metal ,IP30 Protection

Case Dimension (L x W x D)

142mmx36.2mmx105mm (LxWxD)

Installation mounting

DIN Rail mounting and Wall Mounting

Certifications:

EN55022/24

ITE equipment

EN55011

Industrial, Scientific and Medical (ISM) equipment

Safety

IEC EN60950-1

EMC/EMS

CE, FCC, VCCI

EMI

FCC Part 15 Subpart B Class A,

CE EN 55022 Class A

EN 50155 / EN 60068-2-6

Vibration

EN 50155 / EN 60068-2-27

Shock

EN 50155 / EN 60068-2-32

Free Fall

Housing Dimension

Table des matières

Autres manuels Repotec Changer

Repotec

Repotec RP-G2602D Manuel utilisateur

Repotec

Repotec RP-G1408Q Manuel utilisateur

Repotec

Repotec RP-G802W Manuel utilisateur

Repotec

Repotec RP-1716DR2 Manuel utilisateur

Repotec

Repotec RP-G1600U Manuel utilisateur

Repotec

Repotec RP-1705K Manuel utilisateur

Repotec

Repotec GEL2P-ESW26G Manuel utilisateur

Repotec

Repotec GEL2P-ESW10G Series Manuel utilisateur

Repotec

Repotec RP-PE054J/F Manuel utilisateur

Repotec

Repotec 16 Gigabit L2 Managed Switch Manuel utilisateur

Repotec

Repotec GEPOESM-ESW26K Series Manuel utilisateur

Repotec

Repotec RP-G1510W Manuel de l'opérateur

Repotec

Repotec RP-G108Q Manuel utilisateur

Repotec

Repotec RP-PEG08-H Manuel utilisateur

Repotec

Repotec RP-G0401DC Manuel utilisateur

Repotec

Repotec RP-G1416Q Manuel utilisateur

Repotec

Repotec RP-IPG402A Manuel utilisateur

Repotec

Repotec RP-1649RE Manuel utilisateur

Repotec

Repotec RP-PG081W Manuel utilisateur

Repotec

Repotec RP-IPG814-2F Manuel utilisateur

Repotec

Repotec RP-PE801 Manuel utilisateur

Repotec

Repotec RP1024W Manuel utilisateur

Repotec

Repotec RP-PEG08 Manuel utilisateur

Repotec

Repotec RP-G1416D Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur