Reolink RLC-1212A Guide de démarrage rapide
Operational
RLC-1212A
Instruction
EN/DE/FR/IT/ES
3 4
VGAHDMIUSB
AUDIO
OUT
DC 48V
ON
2 4 6 8
1 3 5 7
OFF
LAN
eSATA
Connection DiagramCamera Introduction
Before using the camera, please connect your camera as instructed
below to finish initial setup.
1. Connect the camera to a Reolink NVR (not included) with an Ethernet
cable.
2. Connect the NVR to your router, and then power on the NVR.
* You may also connect the camera to a PoE switch or PoE injector.
NOTE: The camera should be powered with a 12V DC adapter or a PoE
powering device such as PoE injector, PoE switch or Reolink NVR
(not included in the package).
PoE IP Camera
Ethernet Cable
Reolink NVR* Router
Ethernet Cable
Power Adapter
Mount
Micro SD Card Slot
Spotlight
Daylight Sensor
Infrared Lights
Lens
Built-in Mic
Speaker
Waterproof Lid
Network Cable
Reset Button
Power Port(Optional)
* Press for about 10 seconds to restore the
device to factory settings.
5 6
Mount the Camera
• Do not face the camera towards any light sources.
• Do not point the camera towards a glass window. Or, it may result in
poor image quality because of the window glare by infrared LEDs,
ambient lights or status lights.
• Do not place the camera in a shaded area and point it towards a
well-lit area. Or, it may result in poor image quality. To ensure best image
quality, the lighting condition for both the camera and the capture object
shall be the same.
• To ensure better image quality, it’s recommended to clean the lens with
a soft cloth from time to time.
• Make sure the power ports are not directly exposed to water or
moisture and not blocked by dirt or other elements.
• With IP waterproof ratings, the camera can work properly under
conditions like rain and snow. However, it doesn't mean the camera can
work underwater.
• Do not install the camera at places where rain and snow can hit the lens
directly.
• The camera may work in extreme cold conditions as low as -25°C.
Because when it is powered on, the camera will produce heat. You may
power on the camera indoors for a few minutes before installing it
outdoors.
Installation Tips
Set up the Camera
• On Smartphone
Scan to download the Reolink App.
Download and launch the Reolink App or Client software, and follow the
onscreen instructions to finish initial setup.
NOTE: If you are connecting the camera to a Reolink PoE NVR,
please set up the camera via the NVR interface.
English English
7 8
Install the Camera
Drill holes in accordance with the
mounting hole template. To get the best field of view, loosen
the adjustment knob on security
mount and turn the camera.
Stien the adjustment knob to
lock the camera.
Install the mount base with the
mounting screws included in the
package.
NOTE: Use the drywall anchors
included in the package if needed.
NOTE: Run the cable through the
cable notch on the mount base.
24
13
9 10
Specifications
Power: By PoE (802.3af)/DC 12V
Day/Night Mode: Auto Switchover
Operating Temperature: -10°C to 55°C (14°F to 131°F)
Operating Humidity: 10%-90%
.
If the spotlight on your camera is not on, please try the following
solutions:
• Ensure the spotlight is enabled under Device Settings page via Reolink
App/Client.
• Upgrade the firmware of your camera to the latest version.
• Restore the camera to factory settings and check out the spotlight light
settings again.
Hardware Features
General
Spotlight is not On
Troubleshooting
If your camera is not powering on, please try the following solutions:
• Make sure your camera is powered properly. The PoE camera should
be powered by a PoE switch/injector, the Reolink NVR or a 12V power
adapter.
• If the camera is connected to a PoE device as listed above, connect the
camera to another PoE port and see if the camera will power on.
• Try again with another Ethernet cable.
If the picture from the camera is not clear, please try the following
solutions:
• Check the camera lens for dirt, dust or spiderwebs, please clean the
lens with a soft, clean cloth.
• Point the camera to a well-lit area, the lighting condition will aect the
picture quality a lot.
• Upgrade the firmware of your camera to the latest version.
• Restore the camera to factory settings and check out again.
Camera is not Powering On
Picture is not Clear
11 12
This marking indicates that this product should not be disposed with
other household wastes.throughout the EU. To prevent possible harm
to the environment or human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable reuse of material
resources. To return your used device, please use the return and
collection systems or contact the retailer where the product was
purchased. They can take this product for environmentally safe recycling.
Correct Disposal of This Product
Waterproof Rating: IP66
. .
Notification of Compliance
This device complies with Part 15 of FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Reolink declares that this device is in compliance with the essential
requirements and other relevant provisions of Directive 2014/30/EU.
FCC Compliance Statement
Simplied EU Declaration of Conformity
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This product comes with a 2-year limited warranty that is valid only if
purchased from Reolink Ocial Store or a Reolink authorized reseller.
Limited Warranty
NOTE: We hope that you enjoy the new purchase. But if you are not
satisfied with the product and plan to return, we strongly suggest that
you reset the camera to factory default settings before returning.
Use of the product is subject to your agreement to the Terms of Service
and Privacy Policy Keep out of reach of children.
Terms and Privacy
Deutsch 14English13
By using the Product Software that is embedded on the Reolink product,
you agree to the terms of this End User License Agreement (“EULA”)
between you and Reolink.
End User License Agreement
Lieferumfang 15
Allgemeine Einführung 16
Diagramm für Kameraanschluss 17
Kamera-Einrichtung 18
Installation der Kamera 19
Fehlerbehebung 22
Spezifikationen 23
Konformitätserklärung 24
Überblick
DE
Deutsch Deutsch15 16
Lieferumfang
Päckchen
mit Schrauben
Kamera Wasserdichter
Deckel
Netzwerkkabel
Schild
Videoüberwachung
Kurzanleitung Montage-
Lochschablone
Allgemeine Einführung
Montagesockel
MicroSD-Kartenslot
Internes Mikrofon
Lautsprecher
Wasserdichter Deckel
Netzwerkkabel
Reset-Taste
Strom (Optional)
* Zum Zurücksetzen auf die Werkseinstellungen ca.
10 Sekunden lang drücken.
Spotlight
Tageslichtsensor
Infrarot-Scheinwerfer
Objektiv
Deutsch Deutsch17 18
VGAHDMIUSB
AUDIO
OUT
DC 48V
ON
2 4 6 8
1 3 5 7
OFF
LAN
eSATA
Diagramm für Kameraanschluss
Bitte machen Sie die Kamera wie unten gezeigt verbunden, um die
Ersteinrichtung abzuschließen.
1. Schließen Sie die Kamera mit einem Ethernet-Kabel an einen
Reolink NVR an.
2. Schließen Sie den NVR an den Router an und schalten Sie den
NVR ein.
* Sie können die Kamera auch an einen PoE-Switch oder einen
PoE-Injektor anschließen.
HINWEIS: Die Kamera sollte über einen DC 12V-Stromadapter oder ein
PoEStromversorgungsgerät wie PoE-Injektor, PoE-Schalter oder Reolink
NVR (nicht im Lieferumfang enthalten) mit dem Strom versorgt werden.
PoE IP -Kamera
Netzwerkkabel
Reolink NVR* Router
Netzwerkkabel
Netzadapter
Kamera-Einrichtung
• Smartphone
Scannen zur Installation der Reolink App.
Installieren und starten Sie die Reolink App oder Client-Software
und dann befolgen Sie die Anweisungen auf dem Bildschirm,
um die Ersteinrichtung abzuschließen.
HINWEIS: Wenn Sie die Kamera an einen Reolink PoE NVR anschließen
möchten, bitte richten Sie die Kamera über die NVR-Schnittstelle ein.
Autres manuels pour RLC-1212A
1
Table des matières
Langues :
Autres manuels Reolink Caméra de sécurité
Reolink
Reolink E1 Pro Guide de démarrage rapide
Reolink
Reolink RLC-824A Manuel utilisateur
Reolink
Reolink Argus 2 Manuel utilisateur
Reolink
Reolink Argus 3 Guide de démarrage rapide
Reolink
Reolink Argus Eco Manuel utilisateur
Reolink
Reolink RLC-1010A/B4K11 Guide de démarrage rapide
Reolink
Reolink RLC-523WA Guide de démarrage rapide
Reolink
Reolink Go Guide de démarrage rapide
Reolink
Reolink RLC-812A Guide de démarrage rapide
Reolink
Reolink RLC-511WA Manuel utilisateur
Reolink
Reolink E1 Series Manuel utilisateur
Reolink
Reolink Argus Eco Guide de démarrage rapide
Reolink
Reolink RLC-410-B500 Guide de démarrage rapide
Reolink
Reolink Argus 2E Manuel utilisateur
Reolink
Reolink TrackMix LTE Plus Manuel utilisateur
Reolink
Reolink Reolink Go Plus Manuel utilisateur
Reolink
Reolink Go PT Manuel utilisateur
Reolink
Reolink 2205C Manuel utilisateur
Reolink
Reolink RLC-423 Guide de démarrage rapide
Reolink
Reolink Argus 3 Manuel utilisateur
