RELAX-A-MIST JR-1 Manuel utilisateur

CN2

2010

INSTALLATION INSTRUCTIONS FOR THE TIME AND

TEMPERATURE CONTROL with REMOTE CONTROL

MODELS JR-1, JR-2, JR-3, JR-4

Before commencing with these instructions, ensure that the RELAX-A-MIST

steam generator has been installed according

to the steam generator installation instructions.

1. GENERAL INFORMATION

The RELAX-A-MIST

time and temperature control is a

simple programmable control. The user friendly design

has programmable time and temperature settings. Once

a program is set and running, you may temporarily over

ride the settings by pressing the time or temperature

buttons and pushing the applicable increment arrow.

Upon completion of the timed setting, or halting your

steam bath with the “on/off” button, your temporary over

ride setting will return to the programmed default settings.

Your steam bath is ready for your next use. Power supply

interruptions will not change or delete your default time

and temperature settings.

The digital time and temperature control comes as a

package complete with the following:

1. One programmable time and temperature control.

2. One remote control.

3. One 25 foot cord set (steam generator connection

wire to control) with a modular male plug-in at the

steam unit and a modular female plug-in at the control

in the steam shower or steam room.

The programmable time and temperature control must be

located inside the steam room, approximately 4 feet off

the finished floor and NOT in an area above the steam

nozzles. The thermostat sensor is built into the bottom of

the control. The remote control can only operate the main

control from a direct line of site.

NOTE: Inside of the steam room, the six inch wire on the

back of the Time & Temperature control (with the male

plug), connects into the 25 foot wire (with the female plug).

At the steam generator, the male plug from the 25 foot

wire connects to the female plug located on the side of the

steam generator’s electrical box marked “Timer Switch

and 24 VAC”. The cord set modular female connection

must be identified at the steam generator (do not plug the

switch cord into the automatic drain connection). The

control’s 25 foot cord set wire must be installed during the

rough in, with the male end at the steam generator and

the female end at the area in the steam bath where the

control will be installed on the wall.

2. ROUGH IN

ELECTRICAL (According to local electrical code)

Check to ensure that the Relax-A-Mist

steam

generator has been installed according

LR42682

to the steam generator installation instructions.

Install only the RELAX-A-MIST

25 foot cord set wire

(compatible with the Quick Touch Timer or the Time and

Temperature Control) ensuring that the modular male plug

is located in the area where the steam generator is to be

installed. The modular female connector of the 25 foot

wire should protrude out of the wall about 6 inches into the

shower or steam room where the control will be installed.

You will need to make the hole in the cement board and

the finished tile approx. 7/8" diameter to allow the modular

wire connectors from the control and the 25 foot cord set

to pass back inside the wall for the final installation. DO

NOT ADHERE CONTROL TO WALL UNTIL YOU HAVE

COMPLETED THE STEAM GENERATOR START UP

AND CONTROL PRETEST.

CAUTION CAUTION CAUTION:

DO NOT STRETCH WIRE TIGHT. DO NOT STAPLE

THE WIRE TO STUDS. CHECK ORIENTATION OF

MODULAR CONNECTORS ON CONTROL CORD SET.

NOTE: The electrical "supply" for the steam generator

CANNOT be switched directly by the time and

temperature control.

The power supply cable must be run directly to the

steam generator from the fuse or circuit breaker

panel. The factory supplied cord set must be run from

the steam generator to the timer control. The control

through the class 2 voltage circuitry, activates a

contactor in the steam generator.

3. FINAL INSTALLATION

ELECTRICAL (According to Local Electrical Code)

Check to ensure that the RELAX-A-MIST

steam

generator has been installed according to the steam

generator installation instructions.

Caution: Identify modular connector lock position

before inserting into female connections on

steam unit or switch.

a) At the steam generator electric box, side panel,

remove the protective label from the modular female

plug marked “Remove to Insert Modular

Connector”. Note: There may be a second plug for

Optional Automatic Drain.

b) Insert the male plug of the 25 foot timer cord set, with

the retaining tab to bottom, into the steam

generator electrical box female plug. The female socket

is marked "TIMER SWITCH” and “24 VAC". (The other

female plug is for the optional automatic drain feature.

This female plug may be sealed with a blank plastic cover

if the auto drain option was not factory ordered.).

c) Insert the other end of the 25 foot steam generator

connection cord set onto the male plug of the

programmable time and temperature control.

DO NOT CUT FACTORY WIRING TO INSTALL THE

TIME AND TEMPERATURE CONTROL.

DO NOT FORCE MODULAR CONNECTIONS.

DO NOT ADHERE TIME AND TEMPERATURE

CONTROL TO THE WALL UNTIL THE CONTROL

PRETEST IS SUCCESSFULLY COMPLETED.

d) Once the control pretest is completed, tuck the

excess cord behind the switch into the wall or

electrical box if provided. Peel and stick the control to

the wall. If a gap appears between the wall and the

switch, the perimeter of the switch may be sealed

with silicone, or if single gang electrical box is

provided, adjust the electrical box so as not to

protrude through the finished surface of the wall.

DISCLAIMER

The above information represents suggestions only. Each steam room is unique. RELAX-A-MIST manufactures steam

generators only and therefore can not warrant information given regarding steam room materials or construction techniques.

Final selection of the steam room temperature setting and duration of stay is at the discretion of the operators or owners.

STEAM GENERATOR START UP and CONTROL PRETEST

To start, make sure that the electrical and water supplies are turned off and that the programmable switch is not illuminated.

Turn on the water supply to the steam generator. No water will enter as the electricity is still off at this point.

Turn on the electrical supply to the steam generator at the electrical panel or power supply switch to start the pretest.

When the correct voltage is supplied to the steam generator the control will illuminate the digits to display 3 bars. Press the

”on/off” button. This will illuminate the display in the control to show numbers (changes from bars) and will energize the

steam generator contactor coil which will be noticeable by an audible "click". When the steam unit’s contactors close, the

water level device and water valve will be energized. The water entering the boiler will be audible in the form of several short

"spurts". The water will stop entering the boiler when the optimum water level has been achieved. The contactor and water

valve are indicated by a red LED light and a green LED light illuminating on the circuit board in the steam generator electrical

box. Once the steam unit water level is satisfied, the green LED light will turn off and the red LED light will remain illuminated,

indicating the steam unit is in the heating mode. Turn off the control as the pretest is now complete.

Peel and stick the control to the wall in the shower or steam room. Press the “on/off” button and start the steam unit.

Approximately 2 minutes after starting the control the steam generator will produce steam and it will be entering the shower

or steam room. The first time the generator is turned on (during the start up), there may be an initial burst of hot water from

the steam nozzle until the steam line has come up to temperature. The water from this start up test should be captured as

it may contain impurities from the soldering process during the rough-in connection of the steam lines. When the steam room

has heated to the control’s programmed set point, sit back and enjoy, RELAX-A-MIST

HOW THE SWITCH WORKS:

The “on/off” button starts and stops the control programs. After a program has been set and saved, simply press the “on/off”

button and temperature and time will be displayed on the readout (only one program can be set and run at a time).

When the “on/off” button is pushed the control readout will first display the temperature of the steam room, followed by the

temperature set point flashing and then the programmed steam bath time in minutes. If the room temperature is lower than

the controls set point temperature, the steam generator heating cycle will start. The heating cycle will raise the temperature

in the steam room to the preset programmed temperature during the count down of the programmed time. When the room

temperature matches the preset temperature (average steam room 115

F, or at your temperature setting) the control will

start and stop the heat and steam entering the room within approximately one degree of the temperature set point. Once

the control has begun the time count down cycle, you may switch the display from time to temperature and adjust the settings

by pressing either the “time” or “temperature” button and the up and down arrows.

While enjoying a steam bath you may override the programmed settings by selecting the time or temperature button. Push

the time button to display the time and arrow up or down for this steam room visit (use) only. Push the temp button and arrow

up or down to change the temperature display reading from “C” to “F”. A second push of the “temp” button while in the temp

mode, will display the set point reading for 15 seconds and can be arrowed up or down to adjust the temperature for this

steam room visit (use) only. Pressing the up or down buttons until the desired increment is reached will not affect your

programmed settings (program settings can only be changed when they are flashing).

When the count down time is complete, the display will change to the 3 red bars and the steam generator will shut off.

You may halt your steam bath program at any time by pushing the “on/off” button.

Quick Tips For User’s

Touch the “on” button...displays...steam room temp / temp shut off setting / time in minutes and arrows - time up/down.

Touch the “temp” button...display...changes readout to show room temperature and arrow buttons change from C to F.

2nd touch...”temp” button...display...changes readout to temp shut off setting and arrows buttons change - temp up/down.

Touching the time button and then the temp button changes the control to display the steam room temp. For programming

instructions see “Setting Your Program”.

SETTING YOUR PROGRAM:

NOTE:

ONCE THE CONTROL IS TURNED ON AND DISPLAYS THE TIME, IT MAY BE PROGRAMMED BY

PRESSING AND HOLDING THE “time” OR “temp” BUTTON FOR MINIMUM - 5 - SECONDS. ONLY ONE

BUTTON AT A TIME. - SETTINGS CAN ONLY BE CHANGED WHEN DIGITS ARE FLASHING.

1. TIME Press and hold the “time” button for 5 seconds until the digits begin to flash. Press the arrow buttons up or

down to increase or decrease the amount of time to program as the default for your steam visits. Touch the time

button to lock in your setting or wait for the digits to stop flashing and automatically lock in. You have

approximately 15 seconds to complete your choice. When the control is restarted your programmed time setting

will appear as the default.

2. TEMP Press and hold the “temp” button for 5 seconds until the display digits flash “SET” and the temperature set

point is flashing. Press the arrow buttons up or down to increase or decrease the temperature setting default

for your steam visits. Touch the temp button to lock in your settings or wait for the digits to stop flashing and

automatically lock in. You have approximately 15 seconds to complete your choice. You have completed

programming the controls startup default settings for time and temperature - congratulations!

SAFETY PARAMETERS IN YOUR PROGRAM:

There are built in safety parameters in your program that you can not change. These safety controls were built in during the

manufacture and limit the time and temperature of your steam room. They control the steam room heat time, the maximum

temperature the room will reach and the length of time one steam visit should last. These parameters are automatically reset

after each use. Maximum temperature 120

F or 49

C. Maximum length of steam visit for one cycle - 60 minutes.

WARRANTY POLICY

For a period of one year from the date of installation, or 18 months from the date of manufacture,

whichever comes first, all parts and assemblies are warranted as to workmanship and materials used

in their manufacture. There is no cosmetic warranty on installed parts or controls. Any RELAX-A-

MIST™ products containing defective parts, if returned prepaid to an authorized service depot within

the one year or 18 month time limit, will be repaired free of charge, F.O.B. the authorized service depot

making such repairs.

The Company will not be responsible for any breakdown, damage, or losses, direct or indirect, arising

in contract or in tort from any cause whatsoever, including failure to follow the Relax-A-Mist installation

instructions specifically, careless handling, improper voltage supply, corrosion and/or electrolysis, or

a buildup of minerals on the parts or assemblies for any reason or from any source; nor for

transportation and/or other charges incurred in the removal , replacement or repair of defective products

or parts; and there are no warranties or conditions expressed or implied or otherwise applicable, to the

company’s products except as expressly stated herein.

WARRANTY IS VOID IF RESIDENTIAL STEAM GENERATOR

ARE USED IN A COMMERCIAL INSTALLATION.

For product information call 1-800-Y-U-STEAM (1-800-987-8326).

AUTHORIZED SERVICE DEPOTS

BRITISH COLUMBIA ALBERTA ALBERTA

LEISURE BATHS LTD. FRASER - BOND LTD. LEHMANN PLUMBING

6909 Antrim Avenue 9452 Almond Crescent SE 3649 73 Avenue

Burnaby, BC V5J 4M5 Calgary, AB T2J 1B6 Edmonton, AB T6B 2T8

TEL (604) 437-4717 TEL (403) 253-7533 TEL (780) 465-4434

or 1-800-987-8326 FAX (403) 253-7583 FAX (780) 465-4595

FAX (604) 437-5776

MANITOBA ONTARIO QUEBEC

BALCAEN & SONS LTD. ACCORD APPLIANCE INC. THOMAS & SCHMIDT

1392 Pembina Hwy #17, 750 Oakdale Rd. 2825 rue Sabourin

Winnipeg, MB R3T 2C1 North York, ON M3N 2Z4 Saint-Laurent, QC H4S 1M9

TEL (204) 475-1506 TEL (416) 743-4181 TEL (514) 745-1556

FAX (204) 287-2222 FAX (416) 743-4183 FAX (514) 745-4777

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels RELAX-A-MIST Régulateurs de température

RELAX-A-MIST

RELAX-A-MIST CR-9 Manuel utilisateur

Manuels Régulateurs de température populaires d'autres marques

Swegon

Swegon LUNAd MB Manuel utilisateur

Lucky Reptile

Lucky Reptile Thermo Control II Manuel utilisateur

SENSORMETRIX

SENSORMETRIX Argon 100 Manuel utilisateur

Fuji Electric

Fuji Electric PXE4 Manuel utilisateur

Yuyao gongyi

Yuyao gongyi XMT-808 series Manuel utilisateur

Selec

Selec TC544C Manuel utilisateur

P.W. KEY

P.W. KEY rt-208gt Manuel utilisateur

Future Design

Future Design FDC-9200 Manuel utilisateur

BH Thermal

BH Thermal BriskONE Manuel utilisateur

Omron

Omron E5EX-H Manuel utilisateur

West Control Solutions

West Control Solutions KS 45 Guide de démarrage rapide

MCS

MCS RITC-15B Manuel utilisateur

SMC Networks

SMC Networks Thermo-con INR-244-639 Manuel utilisateur

eltherm

eltherm Ex-TC It Series Manuel utilisateur

Omron

Omron C200H-TV Series Manuel utilisateur

industrie technik

industrie technik CA1 Manuel utilisateur

KRAL

KRAL EET 32 Manuel utilisateur

dixell

dixell XR420C Schéma de câblage