Reflecta PF 135 Manuel utilisateur

PF 135

User‘s Manual

Table of Contents

TABLE OF CONTENT

CONTENTS

Unpacking your Scanner 4

Installing Software 6

Installing Hardware 7

Sorting & Cleaning Film Strips 8

Loading Filmstrips 10

How to Scan 11

Configure Settings 12

Main User Interface 13

Scan Settings defined 14

Scan Settings - Scanning 15

Tips & Troubleshooting

Reference video links 16

Technical Support information 19

Unpacking your Scanner

Check the package content before getting started. For Quick Installation please refer to Quick Installation Guide.

Important! Save the original box, receipt and packing material should they be needed for future shipping needs.

Package Contents

•Film Scanner / Film feeder

•Power Adapter 12V DC

•USB 2.0 Cable

•Quick Reference User Guide

Warning!

Using any other power adapter can severely damage the scanner and will VOID the product

warranty.

GENERAL GUIDANCE:

• Only use the supplied USB-Cable. Connect the computer to the scanner directly using the USB 2.0 cable.

• Do not use a Hub or extension cable. Only use the USB ports on the rear of desktop computers is supported

• If there are any other devices (multifunction device, printers, scanners, webcam) connected to the computer via

USB make sure they are powered off.

• A minimum of 4 GB RAM (Windows/Mac) and 30GB Hard drive space minimum is required. 6GB RAM or more

highly recommended.

Assembling the unit, once unpackaged, and all

the shipping tape is removed, insert the film feed

guide into the unit

Operating Temperature info

Operating Ambient Temperature Range

50º to 104ºF (10º to 40ºC)

Note:

Do not turn on the scanner unless it is within this range. If the scanner has been

stored or transported outside of this range, allow it to return to within this range before

turning it on. OperatingAmbient Humidity Range 15% to 76% relative humidity (non

condensing)

: Do not turn on the scanner unless it is within this range. If the scanner has

been stored or transported outside of this range, allow it to return to within this range

before turning it on. OperatingAmbient Humidity Range 15% to 76% relative humidity

(non

-condensing)

Note

: If the scanner is stored or to be transported in cold temperature and then brought

into a warm / humid environment condensation may occur.

Installing Software

Be sure to install the software application BEFORE connecting the scanner

Download the appropriate software from www.reflecta.de

Installing Software - PC users if you are unsure please verify if your system is 32 or 64 bit here:

Control Panel\System and Security\System

Download the software using the link provided above, selecting the correct version

a. Once downloaded you need to run the installer to install the software on your system

PC: Open the Downloads folder locate the installer file PF135_Windows…. Double click the installer to begin

Installing, you may encounter a warning Windows protected your PC Select “More info…” and choose Run Anyway

Mac: Open downloads locate the installer file PF135_Mac xxx.. New security protocols require these steps to

allow the software installation. Mac OS 10.7-10.12 - Hold down the "Control" key on the keyboard and click on the

software installer package, then click on "Open" then you will see an unidentified developer warning message select

"Open" to begin the installation process Mac OS 10.13 - Hold down the "Control" key on the keyboard and double

click on the software installer, then you will see an unidentified developer warning message, select "Open" to begin

the installation

Installing the Hardware

a. Once the software has been successfully installed and the system rebooted, if required you are ready to

connect the scanner, Locate the power switch on the back of the device and make sure it is in the OFF

position (circle in) before connecting

b. Assemble the power adapters 2 pieces together if you have not done so already, by sliding the plug

connector into the slot on the adapter until it clicks into position.

c. Connect the AC adapter to the back of the scanner and connect the adapter to a suitable power outlet

d. Connect the USB cable to the back of the scanner then to the appropriate port on the computer (no hubs,

front ports)

Please Note: When installing your new scanner onto a Windows system that already has another USB

connected Flatbed scanner or All-in-one Scan/Copier/Printer device connected via USB , be sure to power

them off to avoid hardware conflicts, this does not apply to Wi-Fi connected device, If you will be using a

Desktop computer, please connect only to the rear USB ports, do not use any type of USB extension cable

or hub to connect the scanner, data transfer is hindered when doing so causing the software to not respond,

or not communicate at all.

When considering scanner placement be sure to leave sufficient room in front of the unit for the film to come

out, otherwise your strips could end up on the floor.

Power on the scanner

FIRST TIME USE: Give a couple of minutes for your computer to connect the scanning device to the correct

hardware drivers installed previously.

Open the scanning software PF 135 from the desktop icon, or (Mac) under Apple menu –Go –Applications

PF 135

Installing Hardware Installing Hardware

Sorting & Cleaning Filmstrips

The scanner is capable of scanning color positive, color negative and black & white 35mm filmstrips, you will

want to sort these by type into their respective groups before beginning to scan, EXAMPLE: Color positives

together, color negatives together and so on, the scanner can hold up to 10 filmstrips at a time, in sizes ranging

from 2 frames up to 6 frames, this unit does not scan rolls of film

This scanner does not support scanning any other sized filmstrips. (i.e. 110, 126 or APS are not supported),

Note: Strips must be in good condition, If filmstrips have any jagged or gnarled edges please trim them so that

they are smooth before inserting into the scanner. No curled strips, and no tape.

Sorting & Cleaning Filmstrips

Sorting & Cleaning Filmstrips continued

If the films have dust on them, clean them before inserting into the scanner, using a 98% or higher rubbing

alcohol solution and a soft dry lint free cloth, dampen cloth and wipe film clean, turn over and wipe the other

side as well, let the films dry completely before inserting into the scanner

For video instruction please Click Here

Sorting & Cleaning continued

Loading Filmstrips

Insert filmstrips with the emulsion (DULL) side down (SHINY side up), when inserting strips you may need to lift

the cover to be certain your film strips are being placed properly under the guides on the film feed holder (Fig.1

& 1a.), these guides aid in the negatives feeding properly into the scanner. When inserting a strips of 4 frames

they need to be inserted as far in as the line shown in (Fig. 2) to be accepted by the scanner for scanning, if

not inserted fully it cannot grab the film and begin scanning. 6 frame strips will stick out above the holder, the

software acknowledges proper insertion on the lower left of the main UI for directions on how to loading

capacity and configuring scan settings please Click Here:

Loading Filmstrips

Fig. 2

How to Scan

Scan - User Interface:

When scanning it is best to not run other tasks on the computer for best performance

a. Power on the scanner, wait for the blue light to become solid indicating it is ready to use

b. Open the CyberView PF135 software application:

PC: Go to Windows Desktop –PF 135 icon

Mac: Apple Menu –Go –Applications –PF 135 App icon

How to Scan

Table des matières

Autres manuels Reflecta Scanner

Reflecta

Reflecta x11-Scan Manuel utilisateur

Reflecta

Reflecta x10-Scan Manuel utilisateur

Reflecta

Reflecta Super 8 Manuel utilisateur

Reflecta

Reflecta X33-Scan Manuel utilisateur

Reflecta

Reflecta 64220 Manuel utilisateur

Reflecta

Reflecta Docking Scanner Manuel utilisateur

Reflecta

Reflecta CyberView X5 MF Manuel utilisateur

Reflecta

Reflecta x10-Scan Manuel utilisateur

Reflecta

Reflecta X6 TouchScan Manuel utilisateur

Reflecta

Reflecta Combo Album SCAN 64400 Manuel utilisateur

Reflecta

Reflecta Super 8 Manuel utilisateur

Reflecta

Reflecta Combo Album Scanner Manuel utilisateur

Reflecta

Reflecta Super8-Normal8 Manuel utilisateur

Reflecta

Reflecta x7-scan Manuel utilisateur

Reflecta

Reflecta X120 Manuel utilisateur

Reflecta

Reflecta DigitDia 5000 Manuel utilisateur

Reflecta

Reflecta DigitDia 6000 Manuel utilisateur

Reflecta

Reflecta xScan Film Scanner Manuel utilisateur

Reflecta

Reflecta IMAGEBOX Manuel utilisateur

Reflecta

Reflecta CyberView X5 MF Manuel utilisateur

Reflecta

Reflecta x4-scan Manuel utilisateur

Reflecta

Reflecta x66-Scan Manuel utilisateur

Reflecta

Reflecta RPS 10M Manuel utilisateur

Reflecta

Reflecta x11-Scan Manuel utilisateur

Manuels Scanner populaires d'autres marques

Plustek

Plustek Scanner Manuel utilisateur

Z/I Imaging

Z/I Imaging PhotoScan 2001 Manuel utilisateur

Renkforce

Renkforce DS100-5M Manuel utilisateur

Image Access

Image Access WideTEK A2 Manuel utilisateur

Canon

Canon imageFORMULA CR-120N Manuel utilisateur

Fujitsu

Fujitsu FI-4860C2 Manuel utilisateur

GeoSlam

GeoSlam ZEB Horizon Instructions d'installation

Kodak

Kodak i5800 Scanner Manuel utilisateur

Kodak

Kodak i7300 Manuel utilisateur

Revopoint

Revopoint POP Manuel utilisateur

Fujitsu

Fujitsu fi-4860C Manuel utilisateur

Eddyfi Technologies

Eddyfi Technologies Floormap X Manuel utilisateur

Faselase

Faselase F6 Manuel utilisateur

Fujitsu

Fujitsu CardMinder Manuel utilisateur

Uniden

Uniden BC340CRS Manuel utilisateur

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Manuel utilisateur

Mustek

Mustek PageExpress 4800 Pro Manuel utilisateur

Optex

Optex 750830 Manuel utilisateur