Reese 37096 Manuel utilisateur

FULL SIZE TRUCK

MULTI-FIT HITCH

Model Number:

37096

•Quick and Easy Installation

•Many NO DRILLApplications

•No Special Tools Required for Installation

•Unique OEM Protective Coating

This Instruction Sheet contains IMPORTANT safety information.

Please read and keep for future reference.

Use ONLY REESE supplied or approved bolts, locknuts, and washer to install

this hitch.

THIS WARNING IS GIVEN IN COMPLIANCE WITH CALIFORNIA PROPOSITION 65

WARNING: This product contains chemicals known to the state of California to cause

cancer, birth defects or other reproductive harm.

READ and Follow all Instructions and safety messages before installing

the Multi-Fit Hitch.

Failure to follow these instructions may result in DEATH or SERIOUS INJURY

DO NOT lubricate threads. Bolt failure may occur due to over tightening.

DO NOT drill or weld to this hitch.

This product complies with safety specification and requirements for the State of New York and VESC

regulation V-5 for connecting devices and towing systems. Weight distributing hitch rating is 6500 lb

maximum gross trailer weight and 650 lb maximum tongue weight. Weight carrying hitch rating is 5000 lb

maximum gross trailer weight and 500 lb maximum tongue weight. Consult vehicle owners manual for

towing recommendations and limitations.

Qty.

(4)

-CENTER SECTION LOCK NUT 1/2-13 Qty.

(2) - HEX HEAD BOLT M14 X 2.00 X 45mm

CL 10.9

Qty.

(4) - CARRIAGE BOLT 1/2-13 X 1.25” - GR 8 Qty.

(4) -BOLT PLATE 1/4” X 1.5” X 3”

Qty.

(2) -LOCKWASHER 9/16” Qty.

(2) - HEX NUT M12 X 1.75 CL 8

Qty.

(2) - CARRIAGE BOLT 1/2-13 X 2.25” - GR 5 Qty.

(8) -BOLT PLATE 3/8” X 1.25” X 2.5”

Qty.

(8) - HEX HEAD BOLT 3/8-16 X 1.25” – GR5 Qty.

(4) -BOLT PLATE 1/4” X 1.0” X 1.5”

Qty.

(2) -HEX HEAD BOLT 1/2”-13 X 2.25” - GR 5 Qty.

(4) -BOLT PLATE 1/4” X 1.0” X 2.0”

Qty.

(6) -CONICAL WASHER 1/2” Qty.

(4) -HEX NUT 1/2” –13

Qty.

(2)

- HEX HEAD BOLT M12 X 1.75 X 45mm

-CL 10.9 Qty.

(8) - WASHER NUTS 3/8 –16

FASTENER KIT CONTAINS THE BELOW ITEMS

(METRIC)

GENERAL INSTRUCTIONS:

1. Remove center section from box and pull side plate assemblies from shipping location. Insert side plate assemblies

into hitch center section. Refer to specific instructions for proper position. Insert the coiled end of pull wire through

hole on rear side of center section and through end of tube. Attach 1/4” bolt plate and 1/2 x 1-1/4 long carriage bolt

as shown above. Pull fasteners through and loosely install 1/2 hex lock nut. Repeat steps for each fastener. The

spare tire may need to be lowered to install the hitch. It will be replaced later.

2. Refer to the application chart to determine the correct installation for your vehicle. (Last page of each language)

FOR ALL INSTALLATIONS: UNLESS OTHER WISE NOTED

1. Torque all 3/8" nuts to 35 lb.ft. 5. Torque all 10mm CL10.9 hardware to 53 lb.ft.

2. Torque all 12mm nuts & bolts to 65 lb.ft. 6. Torque all 5/8” hardware to 100 lb.ft.

3. Torque all 1/2” hardware to 75 lb.ft 7. Torque all 14mm CL10.9 hardware to 115 lb.ft.

4. Torque (4) center section locknuts to 110 lb. ft. 8. Retighten the spare tire if it was loosened.

NOTE: Not all of the hardware will be used in every installation. Paint any bare metal to prevent rust.

TOOLS REQUIRED

3/4” SOCKET & WRENCH

9/16” SOCKET & WRENCH

15MM, 17MM, 18 MM SOCKET

19MM, 21MM, 22MM SOCKET

TORQUE WRENCH

SAFETY GLASSES

SIDE PLATE ASSEMBLY (UP)

SEE SPECIFIC INSTRUCTIONS

FOR PROPER SIDE PLATE ASSEMBLY POSITION

(UP OR DOWN)

MUST INSTALL REAR SIDE BOLT FIRST

1/2” x 1 1/4” CARRIAGE BOLT

1/4” x 1” x 2” BOLT PLATE

1/2” HEX LOCKNUT

PULL WIRE

(SUPPLIED)

CENTER SECTION

CENTER SECTION LOCKNUT

CENTER SECTION

LOCK NUT

CENTER SECTION ASSEMBLY

TOOLS REQUIRED

9/16”, 3/4” SOCKET

21MM SOCKET

TORQUE WRENCH

SAFETY GLASSES

VEHICLE FRAME

1/4” x 1-1/2” x 3”

BOLT PLATE

99-13 CHEVROLET SILVERADO/ GMC SIERRA 1500 PICKUP

1. Remove the two (2) rear M14 bumper bracket bolts.

2. Raise hitch side brackets into position, aligning hole 2 in bracket with the rear most weldnut in frame.

3. Install the M14 X 45 MM hex bolt, 9/16” lock washer, and 3/8” bolt plate though hole 2 and into weldnut in

frame, both sides, finger tight.

4. Install 1/2” x 2 1/4” carriage bolt and block into forward hole of frame that aligns with hole 5 in hitch side

bracket, as shown.

5. Install 3/8” bolt plate, 1/2” conical washer and nut, both sides, finger tight.

6. Install center section as pre-assembled on front page with (4) 3/8” x 1 ¼” bolts and washer nuts, both sides.

Align center section of hitch with center of vehicle. Finger tighten fasteners.

7. Tighten hitch side bracket to frame. Tighten side plate assembly to side bracket. Tighten side bracket

assembly to center section.

HOLE 5

HOLE 2

3/8” x 1 1/4 bolt

3/8” WASHER NUTS

SIDE PLATE ASSEMBLY

CENTER SECTION

HITCH SIDE BRACKET

NOTE:

General assembly - loosely assemble center section (page 1); loosely install side brackets on vehicle (this page);

install center section assembly; tighten all fasteners to proper specifications (page 1)

3/8” x 1-1/4” x 2 1/2”

BOLT PLATE

1/2” X 2 1/4” CARRIAGE BOLT

M14 X 45MM CL10.9 BOLT

EXISTING WELDNUT ON

BUMPER BRACKET

1/2” CONICAL WASHER

1/2” NUT

9/16” LOCK WASHER

3/8” x 1-1/4” x 2 1/2”

BOLT PLATE

INSTALLATION A

TOOLS REQUIRED

9/16”, 3/4” SOCKET

21MM SOCKET

TORQUE WRENCH

SAFETY GLASSES

VEHICLE FRAME

1/4” x 1-1/2” x 3”

BOLT PLATE

01- 07 CHEVROLET SILVERADO/ GMC SIERRA 2500HD PICKUP (07 –CLASSIC ONLY)

1. Remove the two (2) rear most M14 bumper bracket bolts.

2. Raise hitch side brackets and 3/8” bolt plate into position, aligning hole 3 in bracket with the rear most weldnut in frame.

3. Install the M14 x 45mm hex bolt and 9/16 lock washer though hole 3 and into weldnut in frame, both sides, finger tight.

4. Install 1/2” x 2 1/4” carriage bolt and block into hole of frame that aligns with hole 4 in hitch side bracket, as shown.

5. Install 1/2” x 2 1/4” hex bolt and block into hole of frame that aligns with hole 2 in hitch side bracket, as shown.

6. Install 3/8” bolt plate between frame and hitch side bracket at hole 2 and 4, as shown.

7. Finger tighten 1/2” conical washer and nut, both sides.

8. Install center section as pre-assembled on front page with (4) 3/8” x 1 ¼” bolts and washer nuts, both sides. Align

center section of hitch with center of vehicle. Finger tighten fasteners.

9. Tighten hitch side bracket to frame. Tighten side plate assembly to side bracket. Tighten side bracket assembly to

center section.

HOLE 4

HOLE 2

3/8” x 1 1/4 bolt

3/8” WASHER NUTS

SIDE PLATE ASSEMBLY

CENTER SECTION

HITCH SIDE BRACKET

NOTE:

General assembly - loosely assemble center section (page 1); loosely install side brackets on vehicle (this page);

install center section assembly; tighten all fasteners to proper specifications (page 1)

3/8” x 1-1/4” x 2 1/2”

BOLT PLATE

1/2” X 2 1/4” CARRIAGE BOLT

M14 X 45mm BOLT

EXISTING WELDNUT ON

BUMPER BRACKET

1/2” CONICAL WASHER

1/2” NUT

HOLE 3

1/2” NUT

1/2” CONICAL WASHER

9/16” LOCK WASHER

1/2” x 2 1/4” HEX BOLT

INSTALLATION B

TOOLS REQUIRED

9/16”, 3/4” SOCKET

18MM SOCKET

TORQUE WRENCH

SAFETY GLASSES

VEHICLE FRAME

1/4” x 1-1/2” x 3”

BOLT PLATE

97-04 FORD F-150 PICKUP (OLD BODY STYLE)

1. Lower spare tire.

2. Place 1/2” x 2 1/4” bolts and 1/4” bolt plate in rear most hole in frame. Both sides.

3. Aligning hole 1 in bracket with the rear most hole in frame. Raise hitch side bracket, 3/8” bolt plate, 1/2”

conical washer, and 1/2” nut into position, both sides. loosely install nut.

4. Install the 1/2” x 2 1/4” carriage bolt and 1/4” bolt plate though hole in frame that aligns with hole 5 in hitch

side bracket. Install 3/8” bolt plate, 1/2” conical washer and 1/2” nut, both sides, loosely install nut.

5. Install the M12 x 45mm hex bolt and 1/4” bolt plate though hole in frame that aligns with hole 4 in hitch side

bracket. Install 1/2” conical washer and m12 nut, both sides, finger tight.

6. Install center section as pre-assembled on front page with (4) 3/8” x 1 ¼” bolts and washer nuts, both sides.

Align center section of hitch with center of vehicle. Finger tighten fasteners.

7. Tighten hitch side bracket to frame. Tighten side plate assembly to side bracket. Tighten side bracket

assembly to center section.

8. Raise spare tire back into place.

HOLE 5

HOLE 1

3/8” x 1 1/4 bolt

3/8” WASHER NUTS

SIDE PLATE ASSEMBLY

CENTER SECTION

HITCH SIDE BRACKET

NOTE:

General assembly - loosely assemble center section (page 1); loosely install side brackets on vehicle (this page);

install center section assembly; tighten all fasteners to proper specifications (page 1)

3/8” x 1-1/4” x 2 1/2”

BOLT PLATE

1/2” X 2 1/4” CARRIAGE BOLT

1/2” CONICAL WASHER

1/2” NUT

1/2” CONICAL WASHER

1/2” NUT

3/8” x 1-1/4” x 2 1/2”

BOLT PLATE

1/2” CONICAL WASHER

1/2” NUT

1/2” x 2 1/4” HEX BOLT

3/8” x 1-1/4” x 2 1/2”

BOLT PLATE M12 NUT

1/2” CONICAL WASHER

M12 X 45MM BOLT

1/4” X 1” X 1 1/2”

BOLT PLATE

HOLE 4

EXISTING HOLES

INSTALLATION C

TOOLS REQUIRED

9/16”, 3/4” SOCKET

1/2” DRILL BIT

18MM SOCKET

TORQUE WRENCH

SAFETY GLASSES

VEHICLE FRAME

1/4” x 1-1/2” x 3”

BOLT PLATE

99-04 FORD F-250, F-350 SUPER DUTY PICKUP

1.Lower spare tire.

2.Place 1/2” x 2 1/4” bolts and 1/4” bolt plates in noted existing holes in frame. Both sides.

3. Aligning hole 3 and 4 in bracket with bolts in frame. Raise hitch side bracket, 3/8” bolt plate, 1/2” conical washer, and

1/2” nut into position, as shown, both sides. loosely install nuts.

4. Using hole 1 in bracket as a guide, drill a 1/2” hole in frame.

5. Install the M12 x 45mm hex bolt and 1/4” bolt plate though hole in frame. Install 1/2” conical washer and M12 nut, both

sides, finger tight.

6. Install center section as pre-assembled on front page with (4) 3/8” x 1 ¼” bolts and washer nuts, both sides. Align

center section of hitch with center of vehicle. Finger tighten fasteners.

7. Tighten hitch side bracket to frame. Tighten side plate assembly to side bracket. Tighten side bracket assembly to

center section.

8. Raise spare tire back into place.

HOLE 1

3/8” x 1 1/4 bolt

3/8” WASHER NUTS

SIDE PLATE ASSEMBLY

CENTER SECTION

HITCH SIDE BRACKET

NOTE:

General assembly - loosely assemble center section (page 1); loosely install side brackets on vehicle (this page);

install center section assembly; tighten all fasteners to proper specifications (page 1)

3/8” x 1-1/4” x 2 1/2”

BOLT PLATE

1/2” X 2 1/4” CARRIAGE BOLT

1/2” NUT

1/2” CONICAL WASHER

1/2” NUT

1/2” x 2 1/4” HEX BOLT

3/8” x 1-1/4” x 2 1/2”

BOLT PLATE

M12 NUT

M12 X 45MM BOLT

1/4” X 1” X 1 1/2”

BOLT PLATE

HOLE 4

EXISTING HOLES

DRILLED HOLE

HOLE 3

INSTALLATION E

TOOLS REQUIRED

9/16”, 3/4” SOCKET

1/2” DRILL BIT

18MM SOCKET

TORQUE WRENCH

SAFETY GLASSES

94-01 DODGE 1500 PICKUP, 94-02 DODGE 2500 & 3500 PICKUP (SHORT BED)

1.Lower spare tire.

2.Place 1/2” x 2 1/4” carriage bolts and 1/4” bolt plates in noted existing large hole in end of frame. Both sides.

3. Aligning hole 1 in bracket with bolts in frame. Raise 3/8” bolt plate, hitch side bracket, 1/4” bolt plate, 1/2” conical

washer, and 1/2” nut into position, as shown, both sides. loosely install nuts.

4. Pull both hitch side brackets to the rear most of hole in frame.

5. If the vehicle frame has a hole that lines up with hole #4 in hitch side bracket, install fasteners and bolt plates as shown.

If hole doesn’t exist or is to small, drill 1/2” hole in vehicle frame, approximatly centered in #4 hole if small hole doesn’t

exist. Install fasteners and bolt plates as shown.

6. Using hole 3 in bracket as a guide, drill a 1/2” hole in frame. Make sure that there is enough room to place 1/4 x 1 x 1 1/2”

bolt plate flat on the inside of the frame, next to the frame cross member.

7. Install the M12 x 45mm hex bolt and 1/4” bolt plate though hole in frame. Install 3/8” bolt plate, 1/2” conical washer and

M12 nut as shown, both sides, finger tight.

8. Install center section as pre-assembled on front page with (4) 3/8” x 1 ¼” bolts and washer nuts, both sides. Align

center section of hitch with center of vehicle. Finger tighten fasteners.

9. Tighten hitch side bracket to frame. Tighten side plate assembly to hitch side bracket. Tighten side plate assembly to

center section.

10. Raise spare tire back into place.

NOTE:

General assembly - loosely assemble center section (page 1); loosely install side brackets on vehicle (this page);

install center section assembly; tighten all fasteners to proper specifications (page 1)

VEHICLE FRAME

1/4” x 1-1/2” x 3”

BOLT PLATE

HOLE 1

3/8” x 1 1/4” BOLT

3/8” WASHER NUTS

SIDE PLATE

ASSEMBLY

CENTER SECTION

HITCH SIDE

BRACKET

3/8” x 1-1/4” x 2 1/2”

BOLT PLATE

1/2” X 2 1/4”

CARRIAGE BOLT

1/2” NUT

1/2” CONICAL WASHER

1/2” NUT

1/2” x 2 1/4” HEX BOLT

3/8” x 1-1/4” x 2 1/2”

BOLT PLATE

M12 NUT

M12 X 45MM BOLT

HOLE 4

EXISTING HOLES

DRILLED HOLE ON

SOME MODELS

HOLE 3

DRILLED HOLE

1/2” CONICAL WASHER

1/4” x 1-1/2” x 3” BOLT PLATE

1/4” X 1” X 1 1/2”

BOLT PLATE

1/4” x 1-1/2” x 3”

BOLT PLATE

1/4” X 1” X 1 1/2”

BOLT PLATE

3/8” x 1-1/4” x 2 1/2”

BOLT PLATE

1/2” x 2 1/4”

HEX BOLT

M12 X 45MM

BOLT

1/2” X 2 1/4”

CARRIAGE BOLT

3/8” x 1 1/4

BOLT

FRAME CROSS

MEMBER

SUSPENSION

SUPPORT

(HEAVY DUTY

MODELS ONLY)

INSTALLATION F

TOOLS REQUIRED

9/16”, 3/4” SOCKET

1/2” DRILL BIT

18MM SOCKET

TORQUE WRENCH

SAFETY GLASSES

94-01 DODGE 1500 PICKUP, 94-02 DODGE 2500 & 3500 PICKUP (LONG BED)

1.Lower spare tire.

2.Place 1/2” x 2 1/4” carriage bolts and 1/4” bolt plates in noted existing large hole in end of frame. Both sides.

3. Aligning hole 1 in bracket with bolts in frame. Raise 3/8” bolt plate, hitch side bracket, 1/4” bolt plate, 1/2” conical

washer, and 1/2” nut into position, as shown, both sides. loosely install nuts.

4. Pull both hitch side brackets to the forward most of hole in frame.

5. If the vehicle frame has a hole that lines up with hole #4 in hitch side bracket, install fasteners and bolt plates as shown.

If hole doesn’t exist or is to small, drill 1/2” hole in vehicle frame, approximatly centered in #4 hole. Install fasteners and

bolt plates as shown.

6. Using hole 3 in bracket as a guide, drill a 1/2” hole in frame. Make sure that there is enough room to place 1/4 x 1 x 1 1/2”

bolt plate flat on the inside of the frame.

7. Install the M12 x 45mm hex bolt and 1/4” bolt plate though hole in frame. Install 3/8” bolt plate, 1/2” conical washer and

M12 nut as shown, both sides, finger tight.

8. Install center section as pre-assembled on front page with (4) 3/8” x 1 ¼” bolts and washer nuts, both sides. Align

center section of hitch with center of vehicle. Finger tighten fasteners.

9. Tighten hitch side bracket to frame. Tighten side plate assembly to hitch side bracket. Tighten side plate assembly to

center section.

10. Raise spare tire back into place.

NOTE:

General assembly - loosely assemble center section (page 1); loosely install side brackets on vehicle (this page);

install center section assembly; tighten all fasteners to proper specifications (page 1)

VEHICLE FRAME

1/4” x 1-1/2” x 3”

BOLT PLATE

HOLE 1

3/8” x 1 1/4” BOLT

3/8” WASHER NUTS

SIDE PLATE

ASSEMBLY

CENTER SECTION

HITCH SIDE

BRACKET

3/8” x 1-1/4” x 2 1/2”

BOLT PLATE

1/2” X 2 1/4”

CARRIAGE BOLT

1/2” NUT

1/2” CONICAL WASHER

1/2” NUT

1/2” x 2 1/4” HEX BOLT

3/8” x 1-1/4” x 2 1/2”

BOLT PLATE

M12 NUT

M12 X 45MM BOLT

HOLE 4

EXISTING HOLES

DRILLED HOLE ON

SOME MODELS

HOLE 3

DRILLED HOLE

1/2” CONICAL WASHER

1/4” x 1-1/2” x 3” BOLT PLATE

1/4” X 1” X 1 1/2”

BOLT PLATE

1/4” x 1-1/2” x 3”

BOLT PLATE

1/4” X 1” X 1 1/2”

BOLT PLATE

3/8” x 1-1/4” x 2 1/2”

BOLT PLATE

1/2” x 2 1/4”

HEX BOLT

M12 X 45MM

BOLT

1/2” X 2 1/4”

CARRIAGE BOLT

3/8” x 1 1/4

BOLT

FRAME CROSS

MEMBER

SUSPENSION

SUPPORT

(HEAVY DUTY

MODELS ONLY)

INSTALLATION G

Table des matières

Autres manuels Reese Autre

Reese

Reese 58079 Manuel utilisateur

Manuels Autre populaires d'autres marques

GO Industries

GO Industries 38017 Manuel utilisateur

Cissell

Cissell 30LBCMAN2 Manuel utilisateur

RIDGID

RIDGID K-60SP Manuel utilisateur

Gage Bilt

Gage Bilt GB751SH-5 Manuel utilisateur

OVE

OVE SIERRA 60 Manuel utilisateur

ReelCraft

ReelCraft 7800 OLB21 Manuel utilisateur

Body Armor 4x4

Body Armor 4x4 ECO-SERIES Manuel utilisateur

ROBLIN

ROBLIN DROP Guide de l'utilisateur

EMG

EMG EMG-ACB BARREL Manuel de service

MiniSolar

MiniSolar MT-150 Manuel utilisateur

Parkside

Parkside PSZ 250 B2 Manuel utilisateur

ABB

ABB REM 610 Manuel du produit

Parkside

Parkside 55992 Manuel du propriétaire

Skyjacker

Skyjacker F250 Manuel utilisateur

IBM

IBM IBM SYSTEM Z Guide d'installation

Grech Motors

Grech Motors G28 Manuel utilisateur

NOVAK

NOVAK BATTERY CARE SHEET Mode d’emploi

Telemotive

Telemotive blue PiraT Mini Guide de l'utilisateur