RedRobotRC Strider flex 250 Manuel utilisateur

Pololu 5Vstep-down regulator (Included but not soldered)

MinimOSD (Included but not soldered)

Center Plate PDB (x1)

Bottom Plate (x1)

Top Plate (x1)

Arms (x4)

HD Plate (x1)

CCD Board Camera mount (x1)

Aluminum M3 x 6mm (x10) (top plate)

Aluminum M3 x 8mm (x4) (arm pivot)

Aluminum M3 x 10mm (x4) (arm slot)

Aluminum M3 x 16mm (x10) (lower plates)

Nylon M3 x 3mm Spacer (x14) (lower plates)

Nylon M3 x 12mm (x4) (flight controller)

Nylon M3 hex nut (x4) (flight controller)

Nylon 35mm F/F Standoff (x10) (center frame)

Nylon 10mm M/F Standoff (x4) (flight controller)

Rubber Soft Bobbin (x3) (HD plate)

Captive nut (x8) (RROSD plate)

M3 Nylon locking nut (x4) (arm slot)

*Don’t be alarmed if you see extra hardware, those are included as spares

If you find anything missing please contact your retailer or email SUPPORT@REDROTORRC.COM immediately.

M3 Allen/hex key/driver *size #2

M3 Hex socket driver

Soldering Iron with a thick tip

60/40 Rosin core solder or varying thickness

Shrink Tubing of various diameters

(Optional but recommended) Zip ties of varying sizes

(Optional but recommended) Battery Strap (Scorpion or other branded Straps)

(Optional but recommended) Wire Mesh Braid or Paracord

Disclaimer!! - Please understand that quadcopters are potentially dangerous machine. Use the highest level of

precaution when working with hot solder iron, Lipo battery and motors. Make sure to remove props from motor

throughout the entire building process.

MinimOSD –We are not responsible for programming the MinimOSD! As you would when purchasing any

MinimOSD, you must have access to a FTDI Programmer to program/config the MinimOSD

! –Power output on CAM 5V/12V connector –Because a linear regulators are used, limit the current draw to

less than 200mA per rail on 5V and 12V to prevent overheating

! –Battery Polarity –Be sure to hook up your battery leads to the proper pads. Positive lead is clearly

marked with +B+ and Negative lead with -B-. Reversing this can potentially damage your

PDB/Pololu/MinimOSD

! - 4S+1.3Ghz warning –VTX and Camera are both filtered. Only camera power is regulated at (12V or 5V).

Power to the VTX pins is not regulated. The flight battery voltage will be applied directly to your VTX. Most

5.8 Ghz video transmitters have a built in regulator with a wide range to easily accept 3S –4S standard.

Most 1.3 Ghz video transmitters do not have built in regulators and will need a 12V mini regulator in place

on the video out pins if using a 4S flight pack. A product like this can be wired in before the VTX power

connections

! –Power/Ground wire soldering –Caution must be taken when soldering wires to the power and ground

pads on the PDB. There are many sensitive components on the PDB board that a hot soldering iron can ruin

or de-solder if carelessly placed

! –Carbon Fiber –It’s conductive! Watch for shorts on electrical components. The lower frame is grounded

so avoid having positive wires touch the carbon. Be careful when handling carbon as edges are sharp

Below is a list of recommended gear to get you airborne.

Flight Controller (x1)

oCC3D

oNaze32

10A minimum speed controllers (x4)

oRedRotor 12A RapidESC

oKISS ESC 12A/18A

Mini multi-rotor (x4)

oT-Motor 1806-2300kv

oT-Motor 2204-2300kv

oCobra 2204 2300kv

oSunnysky x2204 2300kv

oCobra 2204 1960kv (4S recommended)

18-14 AWG cable (preferably silicon coated) (10”)

Battery connector (Deans, T-plug, XT60, etc. to match your battery style)

3S or 4S LiPo Batteries(1300-2200 mAh range)

5”-6” propellers

o5030

o5040

o5045

o6030

o6045

1 pin Female to Female Standard Servo Cables

Radio Receiver

oFrsky D4R-ii (2.4Ghz recommended)

oEzUHF (long range)

oSpektrum 2.4Ghz

Radio

oFrsky Taranis

oTurnigy 9XR

oSpektrum

Video Transmitter

o600mw Immersion RC (5.8Ghz)

oAomway 200mW (5.8Ghz)

(Optional but recommended) SMA Pigtail lead (4” – 6”)

Video Antenna

oImmersion RC Skew planer Set (5.8Ghz)

FPV Camera

oHS1177

oPZ0420

oSurveilzone CC1526

(Optional but recommended) HD Action Camera

oMobius

oGoPro

Monitor or FPV Goggles

Receiver or FPV Goggles with built in Video Receiver

What is FLEX PDB?

Simply put, the FLEX (flexibility) PDB is power distribution board designed to maximize FPV experience while minimizing

mini quad build time and reducing the wire clutter mess!

PDB built-in features

Thick copper and wide power routing to handle the most demanding power setup

Conveniently located Battery/ESC input solder pads

Built in VTX/CAM LC power filter

3s/4s plug and play

Noise free built-in 5V regulator to power MinimOSD. UHF compatible!

Onboard LEDs for orientation and chase lights (3 rear, 2 front), controlled by manual switch

Conveniently located onboard front/rear RGB LEDs power/signal connectors. Onboard switching regulator can

power up to 20 RGB leds

Built-in current sensor (up to 100A)

Built-in RSSI signal conditioning circuit to handle pwm and analog rssi signal types

MinimOSD Plug-and-Play –no extra wiring required for MinimOSD to access battery voltage, current, rssi, video

in/out

Dual purpose MinimOSD prog. Connector –the 3 pins serves as programming connector and also as telemetry

data connector to naze32 or cc3d

Pololu output pins to provide 5V power

Built-in tiny and loud 5V buzzer

PDB Connection Diagram

Battery Input –Main battery cable solder pads

ESC Pads –ESC power input pads x4

LEDS –2 front and 3 rear built in LEDs

LED Switch –Manual On/Off switch for onboard LEDs

RGB LED Strip –Rear RGB led connector. Pin definition: ground, +5 (500mA), Data in (connect to RGB signal pin)

DIN&DOUT –Connect DIN to front RGB strip Din signal. Connect DOUT to front RGB strip Dout signal. Leave

these two pins alone if you don’t have a front RGB Led strip

Front RGB Select –Connect the two pads with a small blob of solder if you’re not using front RGB Led strip.

Leave the pads unconnected if you have front RGB Led. *The solder bridge is there by default

Video TX –VTX connector. Filtered and not regulated. Pin definition: ground, power, video

CAM 12V –FPV cam connector. Filtered and regulated to 12V. Pin definition: ground, +12v, video

CAM 5V –FPV cam connector. Filtered and regulated by Pololu Step-down. Pin definition: ground, +5v, video

Buzzer Input –Use a female-female servo cable to connect to Naze32’s negative “-“buzzer signal pad

Pololu Output –Power output pins from Pololu

RGB Input - Use a female-female servo cable to connect to FC’s RGB Data signal pin

RSSI Input –Use a female-female servo cable to connect to the receiver RSSI signal, pwm and analog compatible.

There’s a built in signal conditioning circuit to convert pwm rssi to analog voltage that MinimOSD can read.

Example: ch-2 on Frsky D4R receiver

MinimOSD Prog. Connector –Data port to program MinimOSD. Can also be used to retrieve telemetry data from

Naze32. Pin definition: RX, TX, DTR. *Must disconnect when Naze32 is connected to PC

1. POLOLU Regulator Installation (SKIP THIS STEP IF YOU DON’T INTEND TO USE RGB LEDS)

Wrap 1-2 layers of Kapton or electrical tape around the Polulu 5V step-down regulator before soldering to the

bottom of the PDB exactly as shown

2. Lay Nylon M3 x 12mm (x4) flat and insert through bottom plate. Top with Nylon M3 x 3mm Spacer (x4)

Manuels Drone populaires d'autres marques

Ryze

Ryze Tello Manuel utilisateur

PowerVision

PowerVision PowerRay Manuel utilisateur

Force1

Force1 rogue F72 Manuel utilisateur

Zerotech

Zerotech DOBBY Manuel utilisateur

Protocol

Protocol VIDEODRONE AP Manuel utilisateur

dji

dji Matrice M210 Manuel utilisateur

MAKE

MAKE Terry Kilby Manuel utilisateur

SYMA

SYMA X440 Manuel utilisateur

RUKO

RUKO F11 Manuel utilisateur

SYMA

SYMA X5UW(720P) Manuel utilisateur

Dynali

Dynali 25 H Mode d’emploi

dji

dji PHANTOM 4 Manuel utilisateur

Atlas

Atlas AtlasPRO Manuel utilisateur

Twodots

Twodots TVVIN BOARD Manuel utilisateur

GDU

GDU SAGA Manuel utilisateur

Ares

Ares ETHOS QX 130 Manuel utilisateur

Walkera

Walkera ZHUN Manuel utilisateur

dji

dji WIND-4 Manuel utilisateur