RCF TS 9918 Manuel utilisateur
USER MANUAL
MANUALE D’USO
TS 9918
TS 9918-W
-Remote control
-Controllo remoto
3
INDEX
INDICE
ENGLISH
SAFETY PRECAUTIONS
DESCRIPTION
FRONT VIEW
SETTINGS, CONNECTION AND INSTALLATION
OPERATION
SPECIFICATIONS
ITALIANO
AVVERTENZE PER LA SICUREZZA
DESCRIZIONE
VISTA FRONTALE
IMPOSTAZIONI, COLLEGAMENTO ED INSTALLAZIONE
FUNZIONAMENTO
DATI TECNICI
4
6
6
7
10
13
14
16
16
17
20
23
4
ENGLISH
SAFETY
PRECAUTIONS
IMPORTANT NOTES
IMPORTANT NOTES
Before connecting and using this product, please read this instruction manual
carefully and keep it on hand for future reference. The manual is to be
considered an integral part of this product and must accompany it when it
changes ownership as a reference for correct installation and use as well as
for the safety precautions.
RCF S.p.A. will not assume any responsibility for the incorrect installation and
/ or use of this product.
WARNING: To prevent the risk of re or electric shock, never expose this
remote control to rain or humidity.
SAFETY PRECAUTIONS
1. All the precautions, in particular the safety ones, must be read with special
attention, as they provide important information.
2. Make sure the audio system has been turned off before connecting TS
9918 remote controls.
3. Make sure all connections have been made correctly.
4. Make sure that no objects or liquids can get into this product, as this may
cause a short circuit.
5. Never attempt to carry out any operations, modications or repairs.
Contact your authorized service centre or qualied personnel should any of
the following occur:
- The remote control does not operate (or works in an anomalous
way).
- Objects or liquids have got into the remote control.
- The remote control has been damaged (due to heavy impacts or
re).
6. Should any part of the remote control emit any strange odour or smoke,
remove it from the line after having immediately switched the system off.
7. Do not connect this product to any equipment or accessories not foreseen.
Check the suitability of the support surface (wall, structure, etc., which the
product is anchored to) and the components used for attachment that must
guarantee the security of the system / installation over time, also considering,
for example, the mechanical vibrations normally generated by loudspeakers.
8. RCF S.p.A. strongly recommends this product is only installed by
professional qualied installers (or specialised rms), who can ensure a
correct installation and certify it according to the regulations in force. The
entire audio system must comply with the current standards and regulations
5
ENGLISH
SAFETY
PRECAUTIONS
regarding electrical systems.
9. Hearing loss
Exposure to high sound levels can cause permanent hearing loss. The acoustic
pressure level that leads to hearing loss is different from person to person
and depends on the duration of exposure. To prevent potentially dangerous
exposure to high levels of acoustic pressure, anyone who is exposed to these
levels should use adequate protection devices. When a transducer capable
of producing high sound levels is being used, it will be necessary to wear ear
plugs or protective earphones.
10. To prevent inductive effects from causing hum, noise and a bad system
working, the remote control cable should not be laid together with other
electric cables (mains), loudspeaker lines, microphone or line level signal
cables or be close to electro-magnetic elds.
11. Install this remote control selector far from any heat source.
12. Do not use solvents, alcohol, benzene or other volatile substances to
clean its external parts. Use a dry cloth.
6
ENGLISH
RCF S.P.A. WOULD LIKE TO THANK YOU FOR PURCHASING THIS
PRODUCT, WHICH HAS BEEN DESIGNED TO GUARANTEE RELIABILITY
AND HIGH PERFORMANCE.
TS 9918 is a touch-sensitive remote control with a slim design and a glass surface,
available both in black (TS 9918) and white (TS 9918-W), for wall mounting (it can
t several standard electrical boxes).
It can be used with: DXT 9000 system,AX 8042 automixer, ZX 8060.
The 8 lateral keys T1-T8 and the volume control VOL at the centre can be
congured through the PC software of the used system.
For instance, every TS 9918 remote control could adjust the level of a single zone
or an audio input, recall a preset, etc. .
It is possible to select among 3 different LED brightness modes (effective when
remote controls are not in use) named NIGHT, SAVING, DAYLIGHT.
DESCRIPTION
FRONT VIEW
T1 - T8: software congurable keys.
L1 - L8: LEDs matched to T1 – T8 keys.
L9 - L16: LED bar indicating the volume
level. The L9, L10 and L11 LEDs also
indicate the selected brightness mode.
U1 and U2: service keys.
VOL: ‘rotary control’ to adjust a level.
L 9 10 11 12 13 14 15 16
L1
T1 T5
T2 T6
T3 T7
T4 U1 U2 T8
L5
L2 TS 9918 L6
L3 L7
L4 L8
7
ENGLISH
SETTINGS, CONNECTION AND INSTALLATION
TS 9918 remote control consists of 2 parts:
1.A frame to t to several standard electrical boxes.
2.A frame with the printed circuit board and the touch-sensitive front panel.
Find both the J1 connector and the six dip-switches on the printed circuit
board (gure 1).
FIGURE 1
J1 CONNECTOR
J1 CONNECTOR
DIP - SW
PIN WIRE COLOUR
1 GND Ground black
2 VCC 24 V dc input red
3 RS 485A RS 485A – serial port (half-duplex, 9600 baud) green
4 RS 485B RS 485B – serial port (half-duplex, 9600 baud) yellow
5 LOCK Link to ground (GND, pin 1) to enable the remote control blue
6 TXD1 Not connected (for programming only) white
8
ENGLISH
DIP-SWITCHES
DIGITAL ADDRESS SETTING
Note: refer to the manual of the used system to know the maximum number
of TS 9918 remote controls on the same line and which digital addresses are
valid.
LINE TERMINATION (RS 485)
Set the dip-switch no.6 to ON only if the TS 9918 remote control is the
last device of its line.
CONNECTION
Before installing the TS 9918 remote control into the electrical box, connect the
rst 5 pins of the J1 connector (on the printed circuit board) to the dedicated
line of the used system:
ground (1), 24 V dc (2), RS 485A (3), RS 485B (4), LOCK (5) to ground.
sw
1ID a
Digital address setting: 0 ÷ 7 (3 bits).
Read the respective manual section.
2ID b
3ID c
4USR To be set to OFF (not used; for future functions)
5BOOT 0 To be set to OFF (it is set to ON for programming only).
6485 TERM Line termination: to be set to ON only if the TS 9918 remote control is
the last device of its line (otherwise, set it to OFF).
DIGITAL ADDRESS ID c dip-switch (3) ID b dip-switch (2) ID a dip-switch (1)
0off off off
1off off ON
2off ON off
3off ON ON
4 ON off off
5 ON off ON
6 ON ON off
7 ON ON ON
9
ENGLISH
INSTALLATION
After connecting the remote control, proceed with its installation
(figures 2 and 3):
1. Fix the frame / adapter Bto the electrical box A(through
suitable screws).
2. Insert (pushing it until it clicks into) the frame with the printed
circuit board and the front panel Cto the frame / adapter B.
FIGURE 2
FIGURE 3 FIGURE 4
The gure 4 shows the section view of the TS 9918 remote control after its
wall mounting.
A
B
C
ABC
10
ENGLISH
If connected to the RCF AX 8042 automixer or ZX 8060, the TS 9918 remote
control can operate in 3 different modes: static, dynamic, combined (both
static and dynamic).
If connected to the DXT 9000 system, the remote control operates
in the static mode only.
Refer to the used system manuals about all concerns the software
conguration of TS 9918 remote controls.
STATIC mode possible functions:
1. Preset recall or other functions previously set in the software (e.g.
‘MUTE INPUT 1’).
2. Level adjustment of an audio input / output or a group.
3. Selection of LED brightness (when the keyboard is locked).
4. Keyboard lock.
DYNAMIC mode possible functions:
1. Level adjustment of either audio inputs (selected with T1-T4 keys) or
audio outputs (T5-T8 keys) previously set in the software.
2. Combining audio inputs and outputs (matrix).
3. Selection of LED brightness (when the keyboard is locked).
4. Keyboard lock.
The COMBINED mode includes functions of both static and dynamic modes.
In this case, the static mode is the normal operation for all users, the dynamic
mode is restricted to professionals only.
OPERATION
Autres manuels pour TS 9918
1
Ce manuel convient aux modèles suivants
1
Table des matières
Langues :
Autres manuels RCF Télécommande
Manuels Télécommande populaires d'autres marques
Panasonic
Panasonic EUR7622KB0 Manuel utilisateur
Bang & Olufsen
Bang & Olufsen Beo4 Manuel utilisateur
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur
Multiplex
Multiplex PROFI TX 9 Manuel utilisateur
One Remote
One Remote RMB4 Manuel utilisateur
FUTABA
FUTABA 9ZAP - PART2 Manuel utilisateur
