Raven AIM Command FLEX Manuel utilisateur

AIM Command FLEX, Patriot

MY 2017 Installation Manual

P/N 016-0171-633 Rev. B 02/17 E29154

While every effort has been made to ensure the accuracy of this document,

Raven Industries assumes no responsibility for omissions and errors. Nor is any

liability assumed for damages resulting from the use of information contained

herein.

Raven Industries shall not be responsible or liable for incidental or consequential

damages or a loss of anticipated benefits or profits, work stoppage or loss, or

impairment of data arising out of the use, or inability to use, this system or any of

its components. Raven Industries shall not be held responsible for any

modifications or repairs made outside our facilities, nor damages resulting from

inadequate maintenance of this system.

As with all wireless and satellite signals, several factors may affect the availability

and accuracy of wireless and satellite navigation and correction services (e.g.

GPS, GNSS, SBAS, etc.). Therefore, Raven Industries cannot guarantee the

accuracy, integrity, continuity, or availability of these services and cannot

guarantee the ability to use Raven systems, or products used as components of

systems, which rely upon the reception of these signals or availability of these

services. Raven Industries accepts no responsibility for the use of any of these

signals or services for other than the stated purpose.

Disclaimer

Table of Contents

P/N 016-0171-633 Rev. B i

Chapter 1 Important Safety Information................................................. 1

Instructions for Wire Routing .....................................................................................................2

Instructions for Hose Routing ....................................................................................................3

Chapter 2 Introduction............................................................................. 7

Required Components ..............................................................................................................7

Tools and Materials Needed ......................................................................................................7

Point of Reference ....................................................................................................................8

Kit Contents ...............................................................................................................................8

Updates ...................................................................................................................................12

Chapter 3 Boom Installation.................................................................. 13

Install Harness Mount Blocks ..................................................................................................13

AIM Command FLEX Nozzle Control Valve Installation ..........................................................13

Best Practices and Recommendations .............................................................................13

Boom Cable Routing and Connection .....................................................................................14

Best Practices and Recommendations .............................................................................14

Secondary Boom Cable Routing and Connections ...........................................................14

Primary Boom Cable Routing and Connections ................................................................15

System Diagram ......................................................................................................................17

Chapter 4 AIM Command FLEX Adapter Harness Installation........... 19

Adapter Harness Installation ...................................................................................................19

Install Nozzle Deflector Brackets on End of the Boom ............................................................22

Table of Contents

ii AIM Command FLEX, Patriot MY 2017 Installation Manual

CHAPTER

Important Safety Information: 1

CHAPTER1

IMPORTANT SAFETY

INFORMATION

Read this manual and all operation and safety instructions included with the implement and/or controller carefully

before installing the AIM Command FLEX system.

• Follow all safety information presented within this manual.

• If you require assistance with any portion of the installation or service of Case IH equipment, contact a local

Case IH dealer for support.

• Follow all safety labels affixed to system components. Be sure to keep safety labels in good condition and

replace any missing or damaged labels. To obtain replacements for missing or damaged safety labels, contact a

local Case IH dealer.

When operating the machine, observe the following safety measures:

• Be alert and aware of surroundings.

• Do not operate agricultural equipment while under the influence of alcohol or an illegal substance.

• Remain in the operator’s position in the machine at all times when equipment is engaged. Disable system

functions or features when exiting from the operator’s seat and machine.

• Do not drive the machine with equipment enabled on any public road.

• Determine and remain a safe working distance from other individuals. The operator is responsible for disabling

AIM Command FLEX when the safe working distance has been diminished.

• Ensure AIM Command FLEX is disabled prior to starting any maintenance work on the system or the

implement.

AGRICULTURAL CHEMICAL SAFETY

• Thoroughly bleed pressure from chemical lines and rinse the system with clean water prior to installing or

servicing fittings, hoses, valves, or nozzles in the application system.

• Always follow safety labels and instructions provided by the chemical manufacturer or supplier.

• Always wear appropriate personal protective equipment as recommended by the chemical and/or equipment

manufacturer.

• Fill, flush, calibrate, and decontaminate chemical application systems in an area where runoff will not reach

ponds, lakes, streams, livestock areas, gardens, or populated areas.

• Avoid inhaling chemical dust or spray particulate and avoid direct contact with any agricultural chemicals. Seek

immediate medical attention if symptoms of illness occur during, or soon after, use of agricultural chemicals,

products, or equipment.

• After handling or applying agricultural chemicals:

NOTICE

DANGER

CHAPTER 1

2 AIM Command FLEX, Patriot MY 2017 Installation Manual

•Thoroughly wash hands and face after using agricultural chemicals and before eating, drinking, or

using the rest room.

•Thoroughly flush or rinse equipment used to mix, transfer, or apply chemicals with water after use

or before servicing any component of the application system.

• Follow all federal, state, and local regulations regarding the handling, use, and disposal of agricultural

chemicals, products, and containers. Triple-rinse and puncture or crush empty containers before disposing of

them properly. Contact a local environmental agency or recycling center for additional information.

ELECTRICAL SAFETY

• Always verify that the power leads are connected to the correct polarity as marked. Reversing the power leads

could cause severe damage to the equipment.

• Disconnect the AIM Command FLEX system ECUs and control console before jump starting the vehicle or

welding on any part of the implement or machine.

INSTRUCTIONS FOR WIRE ROUTING

The word “harness” is used to mean all electrical leads and cables, bundled and unbundled. When installing

harness, secure it at least every 30 cm (12in) to the frame. Follow existing harness as much as possible and use

these guidelines:

Harness should not contact or be attached to:

• Lines and hoses with high vibration forces or pressure spikes

• Lines and hoses carrying hot fluids beyond harness component specifications

Avoid contact with any sharp edge or abrading surfaces such as, but not limited to:

• Sheared or flame cut edges

• Edges of machined surfaces

• Fastener threads or cap screw heads

• Ends of adjustable hose clamps

• Wire exiting conduit without protection, either ends or side of conduit

• Hose and tube fittings

Routing should not allow harnesses to:

• Hang below the unit

• Have the potential to become damaged due to exposure to the exterior environment. (i.e. tree limbs, debris,

attachments)

• Be placed in areas of or in contact with machine components which develop temperatures higher than the

temperature rating of harness components

• Wiring should be protected or shielded if it needs to route near hot temperatures beyond harness component

specifications

Harnessing should not have sharp bends

CAUTION

Important Safety Information: 3

IMPORTANT SAFETY INFORMATION

Allow sufficient clearance from machine component operational zones such as:

• Drive shafts, universal joints and hitches (i.e. 3-point hitch)

• Pulleys, gears, sprockets

• Deflection and backlash of belts and chains

• Adjustment zones of adjustable brackets

• Changes of position in steering and suspension systems

• Moving linkages, cylinders, articulation joints, attachments

• Ground engaging components

For harness sections that move during machine operation:

• Allow sufficient length for free movement without interference to prevent: pulling, pinching, catching or

rubbing, especially in articulation and pivot points

• Clamp harnesses securely to force controlled movement to occur in the desired harness section

• Avoid sharp twisting or flexing of harnesses in short distances

• Connectors and splices should not be located in harness sections that move

Protect harnesses from:

• Foreign objects such as rocks that may fall or be thrown by the unit

• Buildup of dirt, mud, snow, ice, submersion in water and oil

• Tree limbs, brush and debris

• Damage where service personnel or operators might step or use as a grab bar

• Damage when passing through metal structures

IMPORTANT:Avoid directly spraying electrical components and connections with high pressure water. High pressure water

sprays can penetrate seals and cause electrical components to corrode or otherwise become damaged.

When performing maintenance:

•Inspect all electrical components and connections for damage or corrosion. Repair or replace

components, connections, or cable as necessary.

•Ensure connections are clean, dry, and not damaged. Repair or replace components, connections,

or cable as necessary.

•Clean components or connections using low pressure water, pressurized air, or an aerosol electrical

component cleaning agent.

•Remove visible surface water from components, connections, or seals using pressurized air or an

aerosol electrical component cleaning agent. allow components to dry completely before

reconnecting cables.

INSTRUCTIONS FOR HOSE ROUTING

The word “hose” is used to mean all flexible fluid carrying components. Follow existing hoses as much as possible

and use these guidelines:

Hoses should not contact or be attached to:

• Components with high vibration forces

• Components carrying hot fluids beyond component specifications

Avoid contact with any sharp edge or abrading surfaces such as, but not limited to:

CHAPTER 1

4 AIM Command FLEX, Patriot MY 2017 Installation Manual

• Sheared or flame cut edges

• Edges of machined surfaces

• Fastener threads or cap screw heads

• Ends of adjustable hose clamps

Routing should not allow hoses to:

• Hang below the unit

• Have the potential to become damaged due to exposure to the exterior environment. (i.e. tree limbs, debris,

attachments)

• Be placed in areas of or in contact with machine components which develop temperatures higher than the

temperature rating of hose components

• Hoses should be protected or shielded if it needs to route near hot temperatures beyond hose component

specifications

Hoses should not have sharp bends

Allow sufficient clearance from machine component operational zones such as:

• Drive shafts, universal joints and hitches (i.e. 3-point hitch)

• Pulleys, gears, sprockets

• Deflection and backlash of belts and chains

• Adjustment zones of adjustable brackets

• Changes of position in steering and suspension systems

• Moving linkages, cylinders, articulation joints, attachments

• Ground engaging components

For hose sections that move during machine operation:

• Allow sufficient length for free movement without interference to prevent: pulling, pinching, catching or

rubbing, especially in articulation and pivot points

• Clamp hoses securely to force controlled movement to occur in the desired hose section

• Avoid sharp twisting or flexing of hoses in short distances

Protect hoses from:

• Foreign objects such as rocks that may fall or be thrown by the unit

• Buildup of dirt, mud, snow, ice, submersion in water and oil

• Tree limbs, brush and debris

• Damage where service personnel or operators might step or use as a grab bar

• Damage when passing through metal structures

•High pressure wash

IMPORTANT: Avoid directly spraying electrical components and connections with high pressure water. High pressure water

sprays can penetrate seals and cause electrical components to corrode or otherwise become damaged. When

performing maintenance:

•Inspect all electrical components and connections for damage or corrosion. Repair or replace

components, connections, or cable as necessary.

•Ensure connections are clean, dry, and not damaged. Repair or replace components, connections,

or cable as necessary.

•Clean components or connections using low pressure water, pressurized air, or an aerosol electrical

component cleaning agent.

Important Safety Information: 5

IMPORTANT SAFETY INFORMATION

•Remove visible surface water from components, connections, or seals using pressurized air or an

aerosol electrical component cleaning agent. Allow components to dry completely before

reconnecting cables.

CHAPTER 1

6 AIM Command FLEX, Patriot MY 2017 Installation Manual

Table des matières

Autres manuels Raven Matériel agricole

Raven

Raven CRX ROS-RS1 Manuel utilisateur

Raven

Raven SmarTrax Manuel d'utilisation et d'entretien

Raven

Raven PRECISION Solutions SmarTrax Mertz 3300 Manuel utilisateur

Raven

Raven Case IH AutoBoom XRT Manuel d'utilisation et d'entretien

Raven

Raven RS1 Manuel d'utilisation et d'entretien

Raven

Raven AutoBoom UltraGlide XT Manuel utilisateur

Raven

Raven SmarTrax Manuel utilisateur

Raven

Raven SmarTrax Manuel utilisateur

Raven

Raven OmniSeed Manuel utilisateur

Raven

Raven SBGuidance Disc Manuel utilisateur

Raven

Raven SmarTrax Manuel utilisateur

Raven

Raven SBGuidance Side-Shift Manuel utilisateur

Raven

Raven SmarTrax Manuel utilisateur

Raven

Raven Viper Pro Instructions générales

Raven

Raven CaseIH 2100 Series Manuel utilisateur

Raven

Raven TC1 Manuel utilisateur

Raven

Raven SmarTrax Manuel utilisateur

Raven

Raven SmarTrax Manuel utilisateur

Raven

Raven SmarTrax Manuel utilisateur

Raven

Raven SBGuidance Auto Manuel utilisateur

Raven

Raven RS1 Manuel utilisateur

Raven

Raven AutoBoom Manuel utilisateur

Raven

Raven RS1 Manuel utilisateur

Raven

Raven SmarTrax Manuel utilisateur

Manuels Matériel agricole populaires d'autres marques

GSi

GSi PNEG-2314 Manuel utilisateur

Checchi & Magli

Checchi & Magli TEXDRIVE Manuel utilisateur

Amazone

Amazone Cenius 4003-2TX Manuel utilisateur

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Manuel utilisateur

Cima

Cima BLITZ Instructions d'utilisation et d'entretien

Amazone

Amazone CombiDisc 3000 Instructions d'installation

HE-VA

HE-VA Disc-Roller XL Contour Manuel utilisateur

AGT

AGT AGT-SSFM Manuel utilisateur

Milestone

Milestone 72-84 Manuel utilisateur

KUHN

KUHN Hector 3000 Manuel utilisateur

Krone

Krone X-Disc 6200 Manuel utilisateur

Eliet

Eliet DZC450 Manuel utilisateur

Taarup

Taarup BIO+ B4000 Manuel utilisateur

Garland

Garland SHAKER 310 DPG Manuel utilisateur

stable comfort

stable comfort StableWall System Manuel utilisateur

International

International 710 Manuel utilisateur

Ashland

Ashland HDW-3217-14 Manuel utilisateur

TURF TANK

TURF TANK One+ Manuel utilisateur