Raritan SwitchMan USB-Combo SW2 Manuel utilisateur
User’s Manual
SW2
SW4
Copyright © 2008
Raritan, Inc
SW-0B-E JUNE 2008
User’s Manual
SW2
SW4
Raritan, Inc.
400 Cottontail Lane
Somerset, NJ08873
USA
Tel: 1-732-764-8886
Fax: 1-732-764-8887
Http://www.raritan.com
Raritan Europe, B.V.
Eglantierbaan 16
2908 LV Capelle aan den IJssel
The Netherlands
Tel: 31-10-284-4040
Fax: 31-10-284-4049
Http://www.raritan.com
Raritan Japan
4th Floor, Shinkawa NS Building
1-26-2 Shinkawa, Chuo-ku,
Tokyo 104-0033, Japan
Tel: 81-3-3523-5991
Fax: 81-3-3523-5992
Http://www.raritan.co.jp
Raritan Taiwan
5F, 121, Lane 235, Pao-Chiao Rd.,
Hsin-Tien City, Taipei Hsien
Taiwan
Tel: 886-2-8919-1333
Fax: 886-2-8919-1338
Http://www.raritan.com.tw
3
FCC NOTIFICATION
This equipment has been tested and found to comply with the limits a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a commercial installation. This
equipment generates, uses and can radiate radio frequency energy and if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. Operation of this equipment in a residential environment may cause
harmful interference.
Product names mentioned in this document are trademarks or registered trademarks of
their respective companies. PS/2, PC/AT, and IBM are registered trademarks of the
International Business Machines Corporation.
CANADIAN NOTIFICATION
This Class B digital apparatus meets the requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérérique de la classe B respecte toutes les exigences du reglement sur le
matériel brouilleur du Canada.
4
T
TA
AB
BL
LE
E
O
OF
F
C
CO
ON
NT
TE
EN
NT
TS
S
Overview 1
Feature 2
Installtion Procedures 3
Installation Notes 4
Operation 5
Front Panel 5
Selection Channels 5
Scan Channels 5
Set Scan Rate 5
Hot Key Mode 6
Hot-key Activation 6
Select A Computer Channel by Number 6
Select A Computer Channel by Using Arrow Keys 6
Scanning Channels 7
Set Scan Rate 7
Change Hot-key Mode Activator 7
Exit Hot-key Mode 7
Hot-key Command Table 8
Troubleshooting 9
Appendix 11
Specification of SwitchMan 11
Specifications of Cables 11
5
Overview
SwitchMan is the desktop KVM (keyboard, video, mouse) switch for those
who run more than one computer at a desk. By having only one keyboard,
monitor, and mouse, you reclaim your desktop while saving time and
money. SwitchMan uses the same bulletproof design as Raritan's
professional-grade products and is available in two-channel and four-
channel models.
Raritan's unique keyboard and mouse emulation technology dedicates
individual processors to each channel. Every computer continuously "sees"
its own keyboard and mouse to ensure flawless booting and switching. You
can select computers by touching individual channel buttons on the front
panel or by using simple hot-key commands.
SwitchMan's versatile design gives you the choice of either a horizontal or
a space-saving vertical installation. Standard features like Scan and LED
indicators make operation of SwitchMan simple and convenient. Connect
your computers to SwitchMan by using industry standard KVM cables. For
the highest resolution video, use Raritan's premium tangle-proof cables.
Plug your standard PS/2 keyboard, VGA monitor, and PS/2 mouse right
into SwitchMan.
Figure 1. SwitchMan (SW4 4-channel)
6
Feature
∗Compatible with all PS/2-style or AT-style
computers
∗Individual front panel selection buttons with LED
indicators
∗Dedicated keyboard/mouse emulators for each
computer to provide flawless operation
∗High-resolution video to1600X1200
∗PS/2 IntelliMouse support
∗Scan button to scan computers at a
programmable rate
∗Places either horizontally or vertically to save
additional space
∗Powered by connected compuers
∗Use Raritan's premium, tangle-proof cables for
highest resolution video requirements
∗Use inexpensive, industry standard KVM cables
for typical applications.
Figure 2. SW2 (back panel, vertical position)
Figure 3. SW4 (back panel, horizontal position)
7
Installation Procedures
Begin installation by connecting one computer to SwitchMan. Once the first
computer is operational, then connect additional computers.
SwitchMan can use industry standard keyboard, video, and mouse (KVM)
cables or can use Raritan's premium, tangle-proof KVM cables.
Caution: Make sure that each computer is powered OFF before it is
connected to SwitchMan.
1. Connect your keyboard, monitor, and mouse to the back panel of
SwitchMan. Use the black section marked USER PORTS for these
connections.
2. Using either end of the KVM cables, connect the keyboard, monitor, and
mouse connectors to the section marked PC 1 on the SwitchMan back
panel. (See figure 2 for SW2 or figure 3 for SW4)
Note: With Raritan's tangle-proof KVM cables, each connector is
marked with a symbol-keyboard, monitor, mouse-for
ease of connection
3. Plug the other ends of the KVM cable into the corresponding ports on
the first computer
4. Power ON the computer. The LED above the channel selection button
for the powered computer illuminates.
5. The video from the connected computer is displayed on the monitor. The
keyboard and mouse operate as if they were connected directly to the
computer.
Note: SwitchMan is automatically powered ON when at least one
connected computer is powered ON.
6. After the first computer is working, connect the remaining computers to
SwitchMan. Make sure each computer is powered OFF before it is
connected to SwitchMan.
8
Installation Notes
∗Switchman computer ports are PS/2 style. You may also connect AT-
style computers. Use Raritan keyboard/mouse port adapter “APSAT” on
PS/2 cables to plug into a computer with “AT” keyboard port and serial
mouse port.
∗Switchman converts keyboard and mouse signals to PS/2 and requires
either a PS/2 mouse and PS/2 keyboard or an AT Extended keyboard
with
adapter.
Figure 4. Cabling diagram
9
Operation
You can select a computer from the front panel of SwitchMan or through
the keyboard in hot-key mode. The LEDs on the front panel of SwitchMan
indicate which computer, or channel, is currently selected and ready for
use
SwitchMan automatically senses which channels are active-that is, those
that have computers that are connected and powered ON. In Scan mode,
SwitchMan cycles through these active channels. The video is displayed,
and the keyboard and mouse are active for each successive computer.
Front Panel
Select channels
To select a computer from the front panel, simply press the button
corresponding to the desired channel. The LED above the channel
illuminates and the video from that connected computer is displayed. The
keyboard and mouse become active for that computer.
The monitor will remain blank if you choose an inactive channel.
Scan channels
Scan is a feature that automatically steps through each active channel.
When Scan is active, SwitchMan allows you to view the video of each
active channel for a set interval (scan rate). SwitchMan then cycles to the
next active channel. The default scan rate is three seconds. You can set
the scan rate from the front panel or in hot-key mode
To activate Scan, press the scan button on the SwitchMan front panel.
To exit Scan, press the scan button (toggle ON/OFF) again.
Note: SwitchMan automatically skips inactive channels in Scan mode.
Set Scan rate
The scan rate can be changed through front panel buttons to preset
intervals. Press the scan button followed by the channel selection button
that corresponds to the desired scan rate (see chart below). The light
above the button blinks twice to acknowledge the setting, and scanning
continues at the new rate.
10
Channel 1 = 1 second
Channel 2 = 3 seconds
Channel 3 = 8 seconds
Channel 4 = 16 seconds
To exit Scan, press the scan button (toggle ON/OFF).
Hot-Key Mode
When you activate hot-key mode, SwitchMan captures and interprets
keystrokes as front panel functions. No keystrokes pass through to the
computer(s).
Note: Hot-key mode operation requires a PS/2-style or an Extended AT-
style keyboard.
Hot-key activation
To enter hot-key mode, press <Scroll Lock> twice rapidly. SwitchMan
enters hot-key mode, and the three keyboard LEDs-Num Lock, Caps Lock
and Scroll Lock-blink continuously. To exit hot-key mode, press the <Esc>
key.
Select a computer channel by number
You can select channels by using hot-key mode. The LED on the front
panel above the corresponding computer is turned ON.
1. Activate hot-key mode.
2. Press the <c> key.
3. Press number key corresponding to the computer.
4. Press <Enter>.
For example, to select channel two, enter hot-key mode and then press
<c> <2> <Enter>.
Select a computer channel by using arrow keys
In hot-key mode, you can step through the channels. Press the <á> or <à>
arrow to increment and press the <ß> or <â> arrow keys to decrement the
channel numbers.
Autres manuels pour SwitchMan USB-Combo SW2
1
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Raritan Changer
Raritan
Raritan dominion kx III Manuel de service
Raritan
Raritan ConsoleSwitch SCS232 Manuel utilisateur
Raritan
Raritan Switch Manuel utilisateur
Raritan
Raritan IP-Reach IPR-M1 Manuel utilisateur
Raritan
Raritan Dominion KX II Manuel utilisateur
Raritan
Raritan Dominion KX2-864 Manuel utilisateur
Raritan
Raritan DOMINION KSX - Manuel utilisateur
Raritan
Raritan dominion kx III Manuel utilisateur
Raritan
Raritan dominion kx III Manuel utilisateur
Raritan
Raritan Dominion KX II Manuel utilisateur
Raritan
Raritan Dominion KX IV-101 Manuel utilisateur
Raritan
Raritan TMCAT17 series Manuel utilisateur
Raritan
Raritan Dominion SX DSXA-16-DL Manuel utilisateur
Raritan
Raritan PX3TS Manuel utilisateur
Raritan
Raritan Dominion KX Manuel utilisateur
Raritan
Raritan Dominion KSX DKSX440 Manuel utilisateur
Raritan
Raritan Dominion KX Manuel utilisateur
Raritan
Raritan TeleReach TR361 Manuel utilisateur
Raritan
Raritan MCIP18 Manuel utilisateur
Raritan
Raritan PARAGON II Series Manuel utilisateur
