Rae RAELink3 Manuel utilisateur

RAELink3 Mesh or RAELink3 HOST Configuration

1. Hold down [MODE] and [N/-] to enter Programming Mode

(no password is required).

2. Navigate to Op Mode by pressing [N/-].

3. Set the Op Mode to Host.

4. Set the Network ID so that Host and Remote (and Repeater, if

necessary) are the same.

RAELink3 Mesh REMOTE Configuration

Configure communications with Host:

1. Hold down [MODE] and [N/-] to enter Programming Mode

(no password is required).

2. Navigate to Op Mode by pressing [N/-].

3. Set the Op Mode to Remote.

4. Set Network ID to match Host (and Repeater, if necessary).

Configure cable communications with instrument:

1. Hold down [MODE] and [N/-] to enter Programming Mode

(no password is required).

2. Navigate to Op Mode by pressing [N/-].

3. Select the correct cable type.

Use this chart to guide you in choosing the correct setting:

Product

Connection

Setting

ToxiRAE Pro Series

Mesh radio

No setting necessary

MultiRAE Series

Mesh radio

No setting necessary

AP4C

Cable

AP4C

ChemRAE

Cable

ChemRAE

DustTrak2

Cable

DustTrak2

MiniRAE 2000

Cable

Bypass

MultiRAE Plus

Cable

Bypass

ppbRAE Plus

Cable

Bypass

QRAE Plus

Cable

RAE PTP

Simplified connection rules:

ToxiRAE Pro series and MultiRAE Series use mesh radio

wireless connection.

All other products use Cable.

If the name of the product is not listed in the submenu, then

you must use Bypass.

Note: The only exception is the QRAE Plus, which requires

Cable = RAE PTP.

Configure wireless communications with instrument(s):

1. Enter Programming Mode. A password is required

(default is 0000).

2. Navigate to Op Mode.

3. Set PAN ID to match wirelessly connected instrument(s).

4. Set Channel to match wirelessly connected instrument(s).

MultiRAE Wireless Configuration

1. Enter Programming Mode. A password is required (default is 0000).

2. Navigate to Wireless.

3. Turn the radio ON.

4. Set the PAN ID to match the RAELink3 Mesh’s PAN ID.

5. Set the Channel number to match the RAELink3 Mesh’s Channel number.

5a. To automatically find the channel of the corresponding RAELink3

Mesh with the same PAN ID as the MultiRAE, choose “Join Network.”

ProRAE Guardian Configuration

1. Start PC

2. Launch ProRAE Guardian

3. Under the "Command Center" tab click on "Data

Sources"

4. Within the PTM tab configure the following

a. "Serial Port" : Choose the last option in drop down

b. "Unit IDs" : Make sure the Unit ID of the RAELink3

Mesh Remote units is selected

c. "Poll Master Interval(s)" : this setting determines

how often the host modem will poll the remote

RAELink3 Mesh modems

NOTE: "Timeout (ms)" and "Max Retries" settings are

recommended to be set default values of '600' and'3'

5. Hit 'Start'

As the instruments are discovered, they should show

up in the list in the Devices Information Pane, as well

as in the Device List pane. The Google Map (or other

map in use) should show the locations of instruments

with active GPS.

ToxiRAE Pro Wireless Configuration

1. Enter Programming Mode. A password is required (default is 0000).

2. Select Monitor Setup.

3. Select Wireless.

4. Turn the radio ON.

5. Set the 3-digit PAN ID to match the RAELink3 Mesh in Remote mode.

6. Set the Channel to match the RAELink3 Mesh in Remote mode.

6a. To automatically find the channel of the corresponding RAELink3

Mesh with same PAN ID as the ToxiRAE Pro choose "Join Network."

7. Use the default value for Interval. If you want to change the reporting

interval, consult the User’s Guide.

8. You may set the Off Network Alarm, if you want to be notified if the

instrument goes off network or if the network is shut off.

9. Ignore Factory Reset.

10. Exit the Wireless submenu.

RAE Systems Inc.

3775 North First St., San Jose, CA 95134-1708 USA www.raesystems.com Phone: 408-952-8200 Technical Support: [email protected]om Rev. A P/N: 029-4515-000

Before Starting The System

Make sure all batteries are charged.

Make sure all cables and antennas are

connected.

1. Make sure cable between

Host modem and

computer is connected.

2. Start computer, ProRAE

Guardian software, and

Host modem.

3. Start Remote modem.

4. Make sure Network ID on

Host and Remote

modems match.

1. Turn on instrument(s).

2. Make sure PAN ID and

Channel are the same on

both Remote modem and

instrument.

3. Make sure Unit ID is set on

the RAELink3 Mesh.

4. Make sure radio is on.

5. Select “Join Network.”

1. Make sure cable between

instrument and Remote

modem is connected.

2. Make sure Cable type is

set correctly in Remote

modem.

3. Turn on instrument.

4. Make sure baud rate is the

same on both Remote

modem and instrument.

Default = 19200.

5. Make sure Unit ID is set on

instrument.

RAE Systems Inc.

3775 North First St., San Jose, CA 95134-1708 USA www.raesystems.com Phone: 408-952-8200 Technical Support: [email protected]om Rev. A P/N: 029-4515-000

Autres manuels pour RAELink3

Autres manuels Rae Routeur réseau