Radiant RAIN 30 E Manuel utilisateur

CE0694 RAIN 30 E.R - RAD - ING - MAN.UT - 1605.1 - DIGITECH - AUSTRALIA

Technical specification RADIANT BRUCIATORI S.p.A. Montelabbate (PU)

User Manual

for model

RAIN 30 E/R

External wall mounted heating only boiler

USER INSTRUCTIONS

BOILER OPERATING INSTRUCTIONS

Make sure that the authorised technician who tested the boiler has stamped the guarantee booklet.

The installation, first start-up, regulation and maintenance operations must be carried out exclusively by qualified

personnel. Incorrect installation can cause damage to property and injury to persons or animals, for which the

manufacturer will not be held responsible.

During the installation, the technician must carry out the following checks:

■ The data on the data plate must correspond to that of the mains supply networks (gas, electricity, water);

■ The boiler must be regulated according to its designed use and performance;

■ The flue gas exhaust and combustion air intake system must be correctly installed and operational;

■ The exhaust gas discharge and ventilation systems must comply with the requirements of national and local

standards regardless of whether the boiler is installed indoors, outdoors or in its own cabinet (see section

“Reference standards”.

General warnings

 If there is any doubt as to whether the appliance has been tested by an authorised technician, do not attempt

to start it. All maintenance and gas conversion operations MUST BE CARRIED OUT BY PROFESSIONALLY

QUALIFIED PERSONNEL, registered in accordance with current legislation.

 Make sure that the requirements relating to the air intake and ventilation of the room in which the

boiler is to be installed have been complied with.

 The boiler is fitted with an antifreeze system. If the boiler is installed in a location where there is a risk of

freezing, the anti-freeze system will only come into operation if there is power supply to the boiler and the gas

supply valve is open. The manufacturer will not be held responsible for damage to the boiler caused by non-

compliance with this instruction.

 Should any part of the boiler freeze-up, do not attempt to light it under any circumstances, but instead call the

Service Centre immediately.

 The appliance’s combustion system must be checked every two years. This check includes testing the

efficiency of the boiler and must be carried out by authorised personnel possessing the qualifications as

required by current law.

 Do not obstruct the ventilation openings in rooms where there are gas-burning appliances installed (boiler,

cooker, etc.).

USER INSTRUCTIONS

If you smell gas …

 DO NOT ACTIVATE ANY ELECTRIC SWITCHES, TELEPHONES OR ANY OTHER DEVICE THAT MAY

GENERATE ELECTRICAL DISCHARGES OR SPARKS.

 OPEN DOORS AND WINDOWS IMMEDIATELY TO CREATE A CURRENT OF AIR THAT WILL RAPIDLY

CLEAR THE ROOM.

 CLOSE ALL GAS TAPS AND VALVES.

 CALL FOR PROFESSIONALLY QUALIFIED PERSONNEL.

Boiler controls - Control panel

LEGEND

1. ON/OFF BUTTON

2. HEATING TEMPERATURE CONTROL KNOB

3. NOT OPERATIVE KNOB.

4. OUTSIDE TEMPERATURE DISPLAY (ONLY WITH OPTIONAL OUTDOOR SENSOR).

5. SERVICE BUTTON.

6. WINTER MODE SELECTION BUTTON.

7. TERMINAL BOARD FOR EXTERNAL WIRING.

8. TEMPERATURE, ERROR CODE AND OPERATING STATUS DISPLAY .

6754321

Fig. 1

USER INSTRUCTIONS

Starting - up the boiler

 Open the gas Isolation valve located under the boiler.

 Switch on the boiler by placing the ON/OFF switch

(1) in the ON position (see “Control panel”).

 The boiler will light automatically (with the WINTER

mode selected and room thermostat connected).

 Check that there are no flashing numbers on the

display 8 (see error codes). If code H2O appears on

the display 8 this denotes that there is no water in the

boiler. Consequently, fill the system as described in

section “Filling the system”.

■ “WINTER” mode

To switch boiler operation to “WINTER” mode, press

button 6 (see fig. 1). The boiler will only work for the

central heating system. The “WINTER” mode setting of the boiler is signalled by the symbol lit continuously on

the control panel.

The automatic ignition system will light the burner every time there is a demand for room heating. In this case, the

symbol on the control panel will flash.

■ Regulating the heating temperature

The heating temperature is regulated by knob 2 (see fig.1).

 Rotating the knob anticlockwise reduces the temperature.

 Rotating the knob clockwise increases the temperature.

 The range of temperature settings for the central heating runs from a minimum of 30°C to a maximum of 80°C,

or, in the case of low temperature operation, from a minimum of 25°C to a maximum of 59°C.

Fig. 1

6754321

USER INSTRUCTIONS

■ Topping-up the system with water

The water pressure in the central heating circuit must be

checked during the entire period of operation of the boiler.

In this respect, the reading on the pressure gauge M (fig.

2), located on the lower part of the boiler, must not be less

than 1 bar.

If there is insufficient water in the boiler, the code H2O will

flash on the display (see fig 2).

To bring the system back up to pressure, open the

external filling tap R (fig. 2) and use the pressure gauge M

(fig. 2) to check that the system pressure reaches 1 bar

and that the code H2O lights up.

When the operation is complete, close the fill tap.

Diagnostics – Error codes:

This paragraph contains a list of error codes that the boiler may generate on the display 8 (see “Control panel”)

together with the relative indications and the operations that the user can carry out to reset the boiler.

If the problem re-occurs after the following actions have been taken, call an authorised Service

Centre.

_E01_ Ionisation block

Code E01 lit continuously on the display.

 Check that the gas valve on the boiler and gas meter are open and that there is gas in the mains supply (or in

the tank).

 Switch off then switch on the appliance using switch 1 (see “Control panel”) on the control panel.

 When the error code on the display disappears, the boiler will restart.

If the problem persists, Call the Service Centre.

_E02_ Safety Thermostat tripped

Code E02 lit continuously on the display. Call the Service Centre.

_h2o_ Water Pressure Switch tripped

Code H2O lit continuously on the display.

 Check the water pressure in the central heating circuit. The reading on the pressure gauge M (see fig. 2),

located on the lower part of the boiler, must not be less than 1 bar .

 If the pressure is less than 1 bar, top-up the system as described in paragraph “Filling the system”.

 The boiler will restart automatically.

If the problem persists, Call the Service Centre.

_E05_ Heating Sensor malfunction

Code E05 lit continuously on the display. Call the Service Centre.

_E14_ Air Pressure Switch malfunction

Fig. 2

USER INSTRUCTIONS

Code E14 lit continuously on the display. Call the Service Centre.

_E22_Parameter programming request

Code E22 lit continuously on the display. Call the Service Centre.

N.B. If the boiler is to be left unused for a long period of time, the user must do one of the following:

 Make the boiler safe by disconnecting all the power supplies (electricity and gas), and draining the heating

system.

 Leave the boiler in standby, leaving the electricity and gas supplies connected and, consequently the anti-freeze

function.

RADIANT BRUCIATORI s.p.a.

Via Pantanelli, 164/166 - 61025 Loc. Montelabbate (PU)

Tel. +39 0721 9079.1 • fax. +39 0721 9079279

e-mail: tecnico@radiant • Internet: http://www.radiant.it

THE TECHNICAL DATA AND MEASUREMENTS ARE PROVIDED FOR INFORMATION

PURPOSES ONLY AND ARE NOT BINDING. THE COMPANY RESERVES THE RIGHT

TO APPLY VARIATIONS WITHOUT PRIOR NOTIFICATION. NEITHER WILL THE

COMPANY BE HELD RESPONSIBLE FOR ANY INACCURACIES IN THIS HANDBOOK

DERIVING FROM PRINTING OR TRANSLATION ERRORS. E+OEALL RIGHTS

RESERVED. NO PART OF THIS DOCUMENT MAY BE REPRODUCED, MEMORISED

IN ANY FILING SYSTEMS OR TRANSMITTED IN ANY FORM WHATSOEVER,

INCLUDING ELECTRONIC, MECHANICAL, PHOTOCOPIES, RECORDINGS OR ANY

OTHER MEANS WITHOUT THE COMPANY’S PRIOR WRITTEN APPROVAL.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Radiant Chaudière

Radiant

Radiant SF 16 E Manuel utilisateur

Radiant

Radiant RMAS 21 E Manuel

Radiant

Radiant R1K 18 Manuel de service

Radiant

Radiant RKA 34 Manuel utilisateur

Radiant

Radiant R1BK 50 Manuel utilisateur

Radiant

Radiant RS 30 E Manuel

Radiant

Radiant RK 25/B Manuel utilisateur

Radiant

Radiant R1K 34 Manuel utilisateur

Radiant

Radiant RSF 24 E Manuel

Radiant

Radiant R2KA 34 Manuel de service

Radiant

Radiant R2KA 24 /20 Manuel

Radiant

Radiant RKR 24 Manuel utilisateur

Radiant

Radiant Rmas 24 e Manuel utilisateur

Radiant

Radiant R2KA 24 /8 Manuel utilisateur

Radiant

Radiant Slim RBA CS 100 E Manuel utilisateur

Radiant

Radiant RCM-R Manuel utilisateur

Radiant

Radiant RCM Manuel utilisateur

Radiant

Radiant RBC 24 Manuel utilisateur

Radiant

Radiant R2C 28 Manuel utilisateur

Radiant

Radiant R1KR 28 Manuel utilisateur

Radiant

Radiant R1CR 24 Manuel utilisateur

Radiant

Radiant RSF 30 E Manuel

Radiant

Radiant R1K34 Manuel

Radiant

Radiant R1C 34/B Manuel de service

Manuels Chaudière populaires d'autres marques

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Manuel utilisateur

Radijator

Radijator BIO max 23.1 Manuel utilisateur

Brunner

Brunner BSV 20 Manuel utilisateur

Buderus

Buderus Logamax GB062-24 KDE H V2 Manuel utilisateur

Potterton

Potterton 50e Fiche technique

UTICA BOILERS

UTICA BOILERS TriFire Manuel utilisateur

Joannes

Joannes LADY Series Manuel

ECR International

ECR International UB90-125 Manuel d'instructions

Froling

Froling FHG Turbo 3000 Manuel utilisateur

Froling

Froling P4 Pellet 8 - 105 Manuel utilisateur

U.S. Boiler Company

U.S. Boiler Company K2 Manuel utilisateur

Henrad

Henrad C95 FF Manuel utilisateur

NeOvo

NeOvo EcoNox EF 36 Manuel utilisateur

Potterton

Potterton PROMAX SL 12 Manuel utilisateur

Eco Hometec

Eco Hometec EC 25 COMPACT Manuel utilisateur

Viessmann

Viessmann VITODENS 200 Mode d’emploi

Baxi

Baxi Prime 1.24 Manuel utilisateur

REXNOVA

REXNOVA ISA 20 BITHERMAL Manuel utilisateur