Quick-Sling QSMS1201 Manuel utilisateur
391 West Water St.
Taunton,MA 02780
1-800-699-0453
www.Quick-Sling.com
g
Mini Split 12” Stand-Wide Installation: (Please adhere to all local laws and building codes)
Model#: (QSMS1201)
Step #1: Remove U-Bar Frames (2 -
Parts of MS107) from box and stand in
place.
Step #2: Remove Spacer Bar & Saddle
(2 - Parts of MS109) and attach on top
of U-Bar Frames to connect the 2
frames together.
Step #3: Measurethe distance between
foot slots on your Mini-Split Condensing
Unit and position Spacer Bars & Saddle
the same distance apart.
Step #4: Place Mini-Split Stand in place
for installation. It is recommended to
use a plastic, cement or other base to
stabilize your overallinstallation. This
model will fit on a 24” wide base.
Step #5: Place Mini-Split Condensing
Unit on Stand and line-up foot slots with
openings in the Spacer Bar & Saddle.
Step #6: Secure Mini-Split Condensing
Unit to Stand with galvanized hardware
and Anti-Vibration Washers included in
box (Pink & Yellow Labeled Bags).
Step #7: Once Mini-Split Condensing
Unit is secured with enclosed hardware,
secure Spacer Bars & Saddle to the U-
Bar Frame with stainless steel self-
drilling Tech Screws (Tan Labeled Bag).
Step #8: Your Mini-Split Condensing
Unit is now ready for connection to
plumbing and electrical installation
leads.
Photo #1
(On left)
Mini-Split
12” Stand
(Wide) with
Unit. Will fit
on 24”
wide pad.
Photo #2
(On left)
Mini-Split
12” Stand
(side view)
showing
connection
to stand.
Photo #3
(On left)
Mini-Split
12” Stand.
Close-up of
SpacerBar
w Saddle
attachment.
Please see important “Safe Install” information on back page.
Safe Install Warning
Install At Your Own Risk!
The load capacity of this product can only be assured if installation is carried out properly.
Mounting hardware is included with most models. However, it is the Buyer’s sole
responsibility to determine that the enclosed hardware is safe and suitable for the selected
mountinglocation. Additionalmaterialsand safetyprecautionsmay be required, depending
upon the size and location of the installation. When hardware is not included, the Buyer is
solely responsible for furnishing and installing anchors and related mounting materials that
are safe and suitable for the selected mounting location. Quick-Sling™ is not responsible
for any installation faults or defects. It is highly recommended that the installation/mounting
location be periodically inspected by a skilled technician. Make sure that the installation
location is suitable enough to hold the brackets and associated equipment loads.
Disclaimer Of Liability
Quick-Sling LLC and its successors, distributors, jobbers, dealers and retailers (“Seller”)
shall in no way be responsible for any direct, indirect or consequential damage resulting from
improper installation, misuse or misapplication of this product. It is the BUYER’s sole
responsibility for assuring proper installation and use.
Seller makes no warranty of merchantibility of the goods or the
fitness of the goods for any particular purpose. Seller makes no
warranties of any kind, express or implied. The goods are sold as-
is and with all faults.
Table des matières
Autres manuels Quick-Sling Support et étagère
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
