Quest Engineering QR5 Manuel utilisateur
QR5 Rigging Installation Guide
Hang Installation The tilt angle of the vertical hang is controlled by the
shackle location on the top box Touring Spine (1)
The tilt angle for the bottom box is the locking pin at the
base of the hanging bar controlling the tilt angle on the
lower box installation spine (2)
QR5: Vertical Dual Speaker Array Order Ref: ACHPI-QR5
Introduction
The QR5 kit is a specialised two
speaker vertical array box hang. The
link bar allows for two speakers to
be hung from the same point with
individual control over the angle of
each cabinet.
Kit Contents
• Vertical Hanging Link Bar
• Touring Spine assembly
(includes 1 ball lock pin +
2M10 screws)
• Installation Spine (includes 1
ball lock pin + 2M10 screws)
Note: Hanging shackle not
supplied
Move ball lock pin to connect
shackle for desired tilt angle
1
Insert ball lock to set tilt angle
of lower box
2
QR5 Rigging Installation Guide
Bracket Installation
HPi110 with t-Spine
and vertical link bar
Hook the vertical link bar at the
back of the top speaker.
1Bolt the 2 M10 screws back in place.
That will lock the vertical bar onto
the speaker. Make sure the screws
are tight.
2
Hook the bottom speaker at the end
of the vertical link bar. (This can be
done before or after the top cabinet
is flown)
3
The angle
shown
is a 15˚
setting.
Select the angle of the second
cabinet (compare to the first one)
by sliding the quick pin in the slots
(operation similar to selecting
the angle for the Wall Mount
assemblies).
4
QR5 Rigging Installation Guide
Safety Precautions
Avoid installing the mounting
hardware on unstable structures,
such as on unreinforced walls or
ceiling beams that are not designed
to carry extra weight.
Refer all installation work to the
dealer from whom the speaker was
purchased. Installation for flying
speaker systems requires extensive
technical knowledge and experience.
The speaker or rigging hardware may
detach if not correctly installed,
resulting in serious injury to people
below.
Check that all elevated work
platforms or other height access
devices (ladders etc.) will safely carry
the weight of the products to be
elevated and the weight of the
installation personnel before starting
the installation.
Be sure to follow the flying
instructions exactly as described. Do
not take shortcuts during the
installation and flying process.
Identify any possible risks or hazards
before beginning the setup\
installation. Time and care should be
taken so as not to expose yourself or
other workers to danger with unsafe
practices.
Check to confirm that suspension
wires are strong enough, correctly
terminated and sufficient to carry the
total load with at least a 4:1 safety
rating.
The connectors of the suspension
wires and belts must be securely
linked with those of the speaker or
rigging hardware.
Be sure to use screws supplied with
the optional flying hardware when
installing any mounting hardware or
the speaker itself.
Install the unit only in a location that
can structurally support the weight
of the unit and the mounting bracket.
Do not use other methods than those
specified to mount the speaker
boxes.
Use nuts and bolts that are
appropriate for the ceilings or wall’s
structure and composition.
Use only the specified mounting
brackets. No warranty is provided
due to damage resulting from a
failure of after-market accessories.
After installation periodically have the rigging and installation
fittings checked by a competent technician or rigging
specialist. Failure to do so may result in a loudspeaker or
rigging element falling and causing injury.
Caution
www.questengineering.com.au
Quest Engineering Pty. Ltd.
130 - 140 Melrose Drive, Tullamarine Vic. 3043 Australia
Phone: +61 (03) 8373 6868
Table des matières
Autres manuels Quest Engineering Support et étagère
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
