Quantum LightSpeed Appliance QLS250 Manuel utilisateur
[Classification: Protected]
24 August 2022
INSTALLING AND
REMOVING DC POWER
SUPPLY UNITS IN CHECK
POINT APPLIANCES
Check Point Copyright Notice
© 2013-2022 Check Point Software Technologies Ltd.
All rights reserved. This product and related documentation are protected by copyright and distributed under
licensing restricting their use, copying, distribution, and decompilation. No part of this product or related
documentation may be reproduced in any form or by any means without prior written authorization of Check
Point. While every precaution has been taken in the preparation of this book, Check Point assumes no
responsibility for errors or omissions. This publication and features described herein are subject to change
without notice.
RESTRICTED RIGHTS LEGEND:
Use, duplication, or disclosure by the government is subject to restrictions as set forth in subparagraph (c)
(1)(ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013 and FAR
52.227-19.
TRADEMARKS:
Refer to the Copyright page for a list of our trademarks.
Refer to the Third Party copyright notices for a list of relevant copyrights and third-party licenses.
Important Information
Installing and Removing DC Power Supply Units in Check Point Appliances|3
Important Information
Latest Software
We recommend that you install the most recent software release to stay up-to-date with the
latest functional improvements, stability fixes, security enhancements and protection against
new and evolving attacks.
Certifications
For third party independent certification of Check Point products, see the Check Point
Certifications page.
Latest Version of this Document in English
Open the latest version of this document in a Web browser.
Download the latest version of this document in PDF format.
Feedback
Check Point is engaged in a continuous effort to improve its documentation.
Please help us by sending your comments.
Revision History
Date Description
24 August 2022 Updated for TE250XN appliances
01 June 2022 Updated for Quantum LightSpeed Appliances
21 February 2022 Rebranding - New Check Point logo
18 January 2022 First release of this document
Table of Contents
Installing and Removing DC Power Supply Units in Check Point Appliances|4
Table of Contents
Introduction
5
QLS250, QLS450, QLS650, and QLS800
6
Removing a DC Power Supply Unit
7
Installing a Replacement DC Power Supply Unit
8
PSU Configuration and Monitoring
8
TE250XN
9
Removing a DC Power Supply Unit
10
Installing a Replacement DC Power Supply Unit
12
Introduction
Installing and Removing DC Power Supply Units in Check Point Appliances|5
Introduction
This guide applies to these Check Point Appliances:
Appliance U In This Document
Quantum LightSpeed Appliance QLS250 2U QLS250
Quantum LightSpeed Appliance QLS450 3U QLS450
Quantum LightSpeed Appliance QLS650 3U QLS650
Quantum LightSpeed Appliance QLS800 3U QLS800
SandBlast Threat Emulation TE250XN 1U TE250XN
QLS250, QLS450, QLS650, and QLS800
Installing and Removing DC Power Supply Units in Check Point Appliances|6
QLS250, QLS450, QLS650, and
QLS800
QLS250, QLS450, QLS650, and QLS800 Appliances have a redundant power supply unit (PSU) and
support DC PSUs.
If necessary, you can replace a PSU. Note that all PSUs on an appliance must be of the same type (DC).
Important - Make sure you are electromagnetically grounded before you install,
uninstall, or replace a PSU. ESD (electrostatic discharge) can damage the appliance.
QLS250 Appliance Rear Panel
QLS450, QLS650, and QLS800 Rear Panel
QLS250, QLS450, QLS650, and QLS800
Installing and Removing DC Power Supply Units in Check Point Appliances|7
Item Description
1 Release lever
2 LED indicator for each power supply unit
nOff - No power cord is connected to any of the PSUs in the system
nGreen - System on
nBlinking green - Power cords are connected to all PSUs, but system is off
nAmber - No power cord is connected to the PSU, but other PSUs in the system are
connected to a power cord
nBlinking amber - Warning that a hardware issue (high temperature, high power, high
current, slow fan) might lead to an issue with the PSU
nBlinking green amber - PSU undergoing Firmware update
3 Extractor handle
4 QLS250 - Two DC PSUs
QLS450, QLS650, and QLS800 - Three DC PSUs (two are required for the appliance to work,
and the third is for redundancy)
5 ESD grounding point
6 Alarm off button for power supply units
Legend
Removing a DC Power Supply Unit
Before you remove a power supply unit, we recommend that you make sure that:
nIn QLS250 - A second DC power supply is installed and connected to a working power source
nIn QLS450, QLS650, and QLS800 - Two other DC power supplies are installed and connected to a
working power source
Or
nThe appliance is shut down.
To remove a power supply unit:
1. Loosen the two DC power cord retaining screws from the power supply.
2. Remove the power cord from the power supply unit.
3. If the alarm sounds, press the Alarm Off button to the right of the power supply units.
4. Press and hold down the release lever as shown.
QLS250, QLS450, QLS650, and QLS800
Installing and Removing DC Power Supply Units in Check Point Appliances|8
5. While holding the release lever, pull the extraction handle to remove the power supply unit.
Note - Remove the power supply unit only with the extraction handle to prevent any
possible damage.
Installing a Replacement DC Power Supply Unit
To install a replacement power supply unit:
1. Insert the power supply unit into the power supply slot.
2. Push in the power supply unit until the release lever clicks.
3. Insert the power cord into the power supply socket.
4. Tighten the two DC power cord retaining screws onto the power supply.
5. Make sure that the power LED is illuminated.
PSU Configuration and Monitoring
See the
Quantum LightSpeed Appliances Getting Started Guide
for PSU configuration and monitoring
options for your appliance model.
TE250XN
Installing and Removing DC Power Supply Units in Check Point Appliances|9
TE250XN
TE250XN Appliances have a redundant power supply unit (PSU) and support DC PSUs.
If necessary, you can replace a PSU. Note that all PSUs on an appliance must be of the same type (DC).
Important - Make sure you are electromagnetically grounded before you install,
uninstall, or replace a PSU. ESD (electrostatic discharge) can damage the appliance.
Item Description
1 DC Power Supply Units
2 Alarm reset button
3 Grounding lug
Legend
TE250XN
Installing and Removing DC Power Supply Units in Check Point Appliances|10
Removing a DC Power Supply Unit
Item Description
1 DC power connector
2 Terminal for - 48V DC wire
3 Terminal for 0V battery return wire
4 Release lever
5 Extraction handle
6 Power LED
7 Grounding lug
Legend
Autres manuels pour LightSpeed Appliance QLS250
1
Ce manuel convient aux modèles suivants
3
Table des matières
Autres manuels Quantum Matériel réseau
Quantum
Quantum SMART-1 6000-L Manuel utilisateur
Quantum
Quantum MC300 Prism Manuel utilisateur
Quantum
Quantum Scalar 50 Guide de démarrage rapide
Quantum
Quantum DX Series Manuel utilisateur
Quantum
Quantum DXi4800 Manuel utilisateur
Quantum
Quantum VS2112-NVR Manuel utilisateur
Quantum
Quantum Lattus S20 Manuel utilisateur
Quantum
Quantum CHECK POINT SPARK 1500 Series Mode d’emploi
Quantum
Quantum FC310 Manuel utilisateur
Quantum
Quantum B DLTSAGE SELLSHEET Manuel utilisateur
Manuels Matériel réseau populaires d'autres marques
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuel utilisateur
Yudor
Yudor YDS-16 Manuel utilisateur
D-Link
D-Link ShareCenter DNS-320L Manuel utilisateur
Samsung
Samsung ES1642dc Instructions d'utilisation
Honeywell Home
Honeywell Home LTEM-PV Instructions de montage
