Pyxis SP-210 Manuel utilisateur

SP-210 User Manual [email protected] | +1 (866) 203-8397 1

SP-210 Bleach Handheld

User Manual

August 23, 2021

Rev. 1.00

Pyxis Lab, Inc.

1729 Majesc Dr. Suite 5

Lafayee, CO 80026 USA

www.pyxis-lab.com

Pyxis Lab Proprietary and Condenal

Table of Contents

1 Introducon 2

1.1 Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2 Specicaons 2

3 Unpacking Instrument 3

3.1 Standard Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

3.2 Oponal Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

4 Installaon 4

4.1 Baery Installaon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

5 Instrument Overview 5

5.1 Control Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

5.2 Main Module On/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

6 Measurement 6

6.1 Bleach Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

6.2 Suspended Solids Chromacity Interference . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

7 Calibraon 7

7.1 Bleach Calibraon (Three-Point with Zero) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

8 Device Informaon and Diagnosis 8

8.1 Bluetooth Connecon to Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

8.2 Factory Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

9 Use with uPyxis® Mobile App 10

9.1 Download uPyxis® Mobile App . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

9.2 Connecng to uPyxis® Mobile App . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

9.3 System Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

9.4 Seng Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

9.5 Datalog Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

10 Use with uPyxis® Desktop App 14

10.1 Install uPyxis® Desktop App . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

10.2 Connecng to uPyxis® Desktop App . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

10.3 System Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

10.4 Seng Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

10.5 Datalog Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

11 Device Maintenance and Precauon 18

11.1 Maintenance Best Pracces and Quick Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

11.2 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

12 Contact Us 18

Warranty Informaon

Condenality

The informaon contained in this manual may be condenal and proprietary and is the property of Pyxis

Lab, Inc. Informaon disclosed herein shall not be used to manufacture, construct, or otherwise reproduce

the goods described. Informaon disclosed herein shall not be disclosed to others or made public in any

manner without the express wrien consent of Pyxis Lab, Inc.

Standard Limited Warranty

Pyxis Lab warrants its products for defects in materials and workmanship. Pyxis Lab will, at its opon, repair

or replace instrument components that prove to be defecve with new or remanufactured components

(i.e., equivalent to new). The warranty set forth is exclusive and no other warranty, whether wrien or oral,

is expressed or implied.

Warranty Term

The Pyxis warranty term is thirteen (13) months ex-works. In no event shall the standard limited warranty

coverage extend beyond thirteen (13) months from original shipment date.

Warranty Service

Damaged or dysfunconal instruments may be returned to Pyxis for repair or replacement. In some in-

stances, replacement instruments may be available for short duraon loan or lease.

Pyxis warrants that any labor services provided shall conform to the reasonable standards of technical com-

petency and performance eecve at the me of delivery. All service intervenons are to be reviewed and

authorized as correct and complete at the compleon of the service by a customer representave, or des-

ignate. Pyxis warrants these services for 30 days aer the authorizaon and will correct any qualifying

deciency in labor provided that the labor service deciency is exactly related to the originang event. No

other remedy, other than the provision of labor services, may be applicable.

Repair components (parts and materials), but not consumables, provided during a repair, or purchased

individually, are warranted for 90 days ex-works for materials and workmanship. In no event will the in-

corporaon of a warranted repair component into an instrument extend the whole instrument’s warranty

beyond its original term.

Warranty Shipping

A Repair Authorizaon (RA) Number must be obtained from Pyxis Technical Support before any product can

be returned to the factory. Pyxis will pay freight charges to ship replacement or repaired products to the

customer. The customer shall pay freight charges for returning products to Pyxis. Any product returned to

the factory without an RA number will be returned to the customer. To receive an RMA you can generate a

request on our website at hps://pyxis-lab.com/request-tech-support/.

Pyxis Technical Support

Contact Pyxis Technical Support at +1 (866) 203-8397, [email protected], or by lling out a request for

support at hps://pyxis-lab.com/request-tech-support/.

SP-210 User Manual [email protected] | +1 (866) 203-8397 1

1 Introducon

The Pyxis SP-210Bleach Handheld measures the mass/mass concentraon of Chlorine in Sodium Hypochlo-

rite Bleach soluon. Without any reagent kits, the SP-210 can quickly test high Sodium Hypochlorite Bleach

concentraon parameters on the spot with high sensivity.

1.1 Main Features

The SP-210 includes the following features:

• Break-through technology measures disinfecon liquids in high concentraon.

• Direct read technology without diluon or reagent.

• Long standby mainframe 10,000+ measurements.

• Can store up to 8 GB of test data (including test me).

• Create user-dened standard curves, view historical data, or analyze data via the uPyxis® App.

2 Specicaons

Table 1. SP-210 Specicaons

Item Specicaon*

Part Number (P/N) 50801

Range 0.01–16% mass/mass

Accuracy 0.01–2%:±0.02% or ±3% of reading

2–16%: ±0.2% or ±3% of reading

Resoluon 0.01–2%: 0.02%

2–6%: 0.2%

Temperature Range 40–106 °F (4–41 °C)

Humidity 85% at 106 °F (41 °C)

Data Storage 30,000 group data storage, Bluetooth transmission

Display 320×240 TFT-LCD, visible under direct sunlight

Power Supply 4 AA alkaline baeries

Typical Baery Life 10,000 readings

Dimension (L ×W×H) 6.69 ×3.15 ×1.77 inch (170 ×80 ×45 mm)

Weight§0.88 lbs (400 g)

Enclosure Rang IP67

Regulaon CE/RoHS

*With Pyxis’s connuous improvement policy, these specicaons are subject to change without noce.

§Baeries excluded

3 Unpacking Instrument

Remove the instrument and accessories from the shipping container and inspect each item for any damage

that may have occurred during shipment. Verify that all items listed on the packing slip are included. If any

items are missing or damaged, please contact Pyxis Customer Service at [email protected]om.

SP-210 User Manual [email protected] | +1 (866) 203-8397 2

3.1 Standard Accessories

• Quick-Start Guide

• Four (4) AA alkaline baeries

• Bluetooth/USB Adapter for Desktop P/N: MA-NEB

• User Manual available online at hps://pyxis-lab.com/support/

3.2 Oponal Accessories

The following oponal accessories can be ordered from Pyxis Customer Service ([email protected]om) or

Pyxis E-Store at hps://pyxis-lab.com/shop/.

Table 2.

Accessory Name Part Number (P/N)

Pyxis Carrying Case for SP-210 50725

SP-210 User Manual [email protected] | +1 (866) 203-8397 3

4 Installaon

4.1 Baery Installaon

The SP-210 is powered by four alkaline baeries. Typical baery life lasts for 10,000 measurements or 10

months. When the baery capacity is crically low, the SP-210 will display a ”LOW BATTERY” warning for 5

seconds and then automacally turn o.

*NOTE*Do not use rechargeable nickel cadmium (NiCad) or lithium baeries.

Replace the baeries to resume operaon of the SP-210 aer the baery warning. The SP-210 will auto-

macally turn on in the measurement mode aer new baeries are installaon.

The SP-210 baery compartment, shown in Figure 1, is on the back side of the instrument. Baeries are

held in place by a cover secured with two Phillips-head screws.

Figure 1. The SP-210 baery compartment

Install baeries using the following steps:

1. Remove the baery compartment cover by loosening the two screws.

2. Remove old baeries and dispose of them properly.

3. Following the posive and negave terminal signs in the compartment boom, snap four new AA

alkaline baeries rmly into the baery holder.

4. Replace the baery compartment cover and ensure that the sealing O-ring is lying at on the baery

holder.

5. Fasten the two screws.

*NOTE*Failure to properly seat the O-ring may result in water damage to the SP-210.

SP-210 User Manual [email protected] | +1 (866) 203-8397 4

5 Instrument Overview

Figure 2.

5.1 Control Keys

The SP-210 has three control keys, as shown in Figure 2. The le ( ), right ( ), and OK ( ) keys

are used to launch acons indicated on the LCD display directly above the keys. The labels above the keys

indicate the funcon associated with each key and funcons can be changed in dierent operaon modes.

5.2 Main Module On/O

To turn on the SP-210: Press momentarily and release.

To turn o the SP-210: Press and hold for about three seconds. Release when the LCD display

turns o. The SP-210 turns itself o aer 60 seconds without user interacon detected. This is done to

conserve baery life.

*NOTE*This auto-me o seng may be customized by the user as desired through the

uPyxis® Mobile or Desktop App.

SP-210 User Manual [email protected] | +1 (866) 203-8397 5

6 Measurement

6.1 Bleach Measurement

1. When powered on, the SP-210 will be in the Bleach measurement mode. The sample can be trans-

ferred to the sample cell using a pipee or sample bole, or sample valve.

*NOTE*Special care should be taken when pouring the sample into the cell to avoid

air bubble entrainment, which can interfere with reading accuracy.

WARNING

Sodium hypochlorite soluon is a highly corrosive and dangerous substance, avoid direct contact with

the skin or eyes, in case of contact with sodium hypochlorite soluon, please immediately wash the

contact area with clean water connuously.

2. Before beginning a measurement, use pure water to rinse the sample cell at least 2–3 mes. then ll

the sample cell with pure water and click Zero for background calibraon.

3. Pour out the pure water in the sample cell, rinse the sample cell with the Bleach soluon to rinse the

sample cell at least 2–3 mes, then ll the sample cell with the Bleach soluon to be tested, and click

”Read” to Read the value.

4. The screen interface will display the concentraon of Bleach soluon.

5. Aer the measurement is completed, pour out the Bleach soluon and ush the sample cell with

clean water unl there is no sodium hypochlorite residue.

*NOTE*The me required to reach a stable reading may be slightly longer if the wa-

ter sample temperature is signicantly dierent than the environmental temperature

at which the SP-210 had been equilibrated (stored).

The SP-210 does not need to be turned o between measurements of samples. Rinsing the sample cell

several mes between samples is recommended. Ambient light does not aect the measurement. The

sample cell does not need to be covered during the measurement.

*NOTE*If the screen goes dark, the mer will quickly turn o the SP-210. Pressing any key

will turn the mer back on. The mer is used to extend baery life.

*NOTE*To avoid residue or contaminaon from the previous soluon, please clean the

sample cell at least three mes.

*NOTE*Be sure to clean the sample cell aer each use of the SP-210 and dry it with a clean

paper towel to avoid over force damage.

6.2 Suspended Solids Chromacity Interference

The SP-210 has extra channels to measure sample suspended solids and color which are used to automa-

cally compensate for any interference caused by these contaminants as high as 20–50 mg/L. If the sample

turbidity and color values determined are too high, an error will show. In such a case, the user should

pre-lter the sample for the Bleach measurement within the compensaon capability of the SP-210.

SP-210 User Manual [email protected] | +1 (866) 203-8397 6

7 Calibraon

7.1 Bleach Calibraon (Three-Point with Zero)

The SP-210 is calibrated using a three-point calibraon, i.e., the zero-point is calibrated with deionized water

rst, and then the slope is calibrated using a concentraon of 1% and 10% sodium hypochlorite standard

soluon.

1. Rinse and ll the sample cell with deionized water.

*NOTE*In case of emergency, you can use ”no sodium hypochlorite” clean sample

water, such as drink water, but please use deionized water to redo the zero calibraon

as soon as possible.

2. Power on the SP-210 by pressing .

3. The SP-210 displays and measures the concentraon of bleach. If deionized water is used, the mea-

sured value will be very low; the value of sodium hypochlorite should be close to zero. A relavely

low non-zero reading (e.g., 0.01 etc.) is not a problem.

4. Press Cal/Sys ( ) to launch the Bleach CALIBRATION screen (Figure 3).

5. Press Zero () to set the zero point.

6. If the calibraon succeeds, a checkmark ( ) and instrucons for the slope calibraon will appear

(Figure 4).

7. Rinse the sample cell three mes with the 1% sodium hypochlorite standard. Fill the sample cell with

the 1% standard.

8. Press Slope (or ) to start the low-point slope calibraon.

9. If the calibraon succeeds, a checkmark ( ) and a ”Calibraon Success” message will appear (Figure

5). Otherwise, a warning message is displayed.

10. Press Connue (or ) to connue to the high-point slope calibraon (Figure 6).

11. Rinse the sample cell three mes with the 10% sodium hypochlorite standard. Fill the sample cell

with the 10% standard.

12. Press Slope (or ) to start the high-point slope calibraon.

13. If the calibraon succeeds, a checkmark ( ) and a ”Calibraon Success” message will appear (Figure

7). Otherwise, a warning message is displayed.

14. Calibraon is now complete. Press Exit () to return to Bleach measurement mode.

*NOTE*Aer calibraon is completed, the SP-210 will not automacally return to

Bleach measurement mode. If you press and hold Exit, the SP-210 will shut down

instead of returning to the measurement mode.

SP-210 User Manual [email protected] | +1 (866) 203-8397 7

Table des matières

Autres manuels Pyxis Instrument de mesure

Pyxis

Pyxis SP-350 Manuel utilisateur

Pyxis

Pyxis SP-395T Manuel utilisateur

Pyxis

Pyxis CR-301 Manuel utilisateur

Pyxis

Pyxis SP-380 Manuel utilisateur

Pyxis

Pyxis ST-774 Manuel utilisateur

Pyxis

Pyxis FS-100 Series Manuel utilisateur

Pyxis

Pyxis SP-380P Manuel utilisateur

Pyxis

Pyxis DW-739 Series Manuel utilisateur

Pyxis

Pyxis PermaCheck EZ-101 Manuel utilisateur

Pyxis

Pyxis ST-590 Series Manuel utilisateur

Pyxis

Pyxis SP-900 Manuel utilisateur

Pyxis

Pyxis SP-395 HST Guide de démarrage rapide

Pyxis

Pyxis SP-800 Manuel utilisateur

Pyxis

Pyxis SP-395 Manuel utilisateur

Pyxis

Pyxis SP-400 Manuel utilisateur

Pyxis

Pyxis PRISM RT-200 Manuel utilisateur

Pyxis

Pyxis IK-765SS-O3 Manuel utilisateur

Pyxis

Pyxis ST-540SS-HR Manuel utilisateur

Pyxis

Pyxis SP-710 Manuel utilisateur

Pyxis

Pyxis SP-395T TTA Manuel utilisateur

Pyxis

Pyxis SP-380 Manuel utilisateur

Pyxis

Pyxis IK-76SSS-S03 Manuel utilisateur

Pyxis

Pyxis SP-910 Guide de référence

Pyxis

Pyxis ST-774 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur