Pyle PLCAPE500 Manuel utilisateur

        

                

         





Model: PLCAPE500

50F Hybrid Super Cap (carbon and eletroniccapacitor)

With Blue Digital Voltage Display

Capacitance .................................……...... 50,000,000 micro farad (50

Farad)

Working Voltage ...............................…….….. 16DC

Surge Voltage .......................................……… 18DC

E.S.R. (Equivalent Series Resistance)------ 0.0015 ohm @120hz/ 25°C

Capacitance Tolerance------------------------ ± 10%

a) 3 digits hi-end blue light display DC voltage meter that can measure

0.1 DCV range.

b) Reverse pole connecting PCB buzz warning function. If the capacitor is

connected incorrectly by reversing the positive and negative wires

during the installation process the PCB will issue a 45 second noise to

warn you.

c) Hi-end platinum plated 100% brass solid parts and chrome plated metal

cover

d) Over voltage limit and low battery voltage limit warning. When the

system voltage peeks over 17.5 DCV or LESS than 10 DCV. The

buzzer on the PCB will issue an audible noise warning.

e) Multiple small capacitance capacitors linked to provide the lowest

inner E.S.R. and largest moment discharge power.

DETAILED FEATURES:







                 

                                  

                  





You must first attach the mounting tabs to the capacitor before mounting

it. Use the supplied hardware shown in the picture to the right. Notice the

small mounting screw hole in the capacitor chassis.

CHARGING THE CAPACITOR AND WIRING:

The capacitor must be charged before connecting the Power and Ground

cables to the capacitor. Failure to charge the capacitor will result in a

large spark generated from the rapid inflow ofcurrent.

To Charge the capacitor:

1. Make Capacitor positive terminal connections with amplifier and

tighten the bolt. Do not over-tighten the bolts!

Caution: Stripped terminals are not covered under the capacitor’s

warranty.

2. Connect the ground cable with battery, amplifier, then refer to the

attached drawing.

3. Place the supplied charging bulb or resistor between the positive

terminal of the capacitor and the battery’s positive terminal. Do this

for 30 seconds or until the charging bulb goes out.

Caution: The charging bulb will get hot!

4. Immediately after the charging process, take out the charging bulb

from the connecting wire. And connect the positive cable of the

battery directly to the positive terminal on the capacitor.







               

                              

                









WHEN YOU WANT TO MOVE THE CAPACITOR FROM

ORIGINAL INSTALLED CAR AUDIO SYSTEM, YOU MUST FIRST

FOLLOW DISCHARGING PROCESS AFTER TAKING OUT THE

CAPACITOR FROM THE CAR AUDIO SYSTEM.

To Discharge the capacitor: With battery power disconnected, place the

light bulb or resistor across the capacitor’s positive and negative terminals

until light goes out or for three minutes if using a resistor.







              

                            

                     ! 

      !       ! 

      !  





            "

            "            "

            " 

One Year Warranty from the date of purchase.



    

        

     ##

####

##





  

           

          

           



Table des matières

Autres manuels Pyle Accessoires automobiles

Pyle

Pyle BlueTech PBT70R Manuel utilisateur

Pyle

Pyle PLCMTR83WIR Manuel utilisateur

Pyle

Pyle PLCMRV8B Black Manuel utilisateur

Pyle

Pyle PLCM21 Manuel utilisateur

Pyle

Pyle PLCM4565 Manuel utilisateur

Pyle

Pyle PLCMDVR72 Manuel utilisateur

Pyle

Pyle PLDCP12 Manuel utilisateur

Pyle

Pyle PLDCP1.2KIT Fiche d'information produit

Pyle

Pyle PLCM4560 Manuel utilisateur

Pyle

Pyle PHUD19 Manuel utilisateur

Pyle

Pyle PLCMTRDVR47 Manuel utilisateur

Pyle

Pyle PLPSC8 Manuel utilisateur

Pyle

Pyle PLCAPE24 Manuel utilisateur

Pyle

Pyle PLDCP25 Manuel utilisateur

Pyle

Pyle PLCMDVR 8 Manuel utilisateur

Pyle

Pyle PBT99 Manuel utilisateur

Pyle

Pyle PLCAPKT12 Fiche d'information produit

Pyle

Pyle PLCMTR26 Manuel utilisateur

Pyle

Pyle PLCPBT25 Manuel utilisateur

Pyle

Pyle PLCM2720 Manuel utilisateur

Pyle

Pyle PLCM7500 Manuel utilisateur

Pyle

Pyle PLCM9200 Manuel utilisateur

Pyle

Pyle PLCM4300WIR Manuel utilisateur

Pyle

Pyle PLCM9200 Manuel utilisateur

Manuels Accessoires automobiles populaires d'autres marques

James Baroud

James Baroud Odyssey Manuel utilisateur

Motorola

Motorola i50sx Manuel utilisateur

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manuel utilisateur

Feniex

Feniex T3 Manuel utilisateur

Renault

Renault 77 11 423 180 Manuel utilisateur

Kia

Kia E8300-4D000 Manuel utilisateur

Brink

Brink 756843 Manuel utilisateur

Whispbar

Whispbar K085W Manuel utilisateur

v.link

v.link CI-VL2-PC-HSD Manuel utilisateur

Viking

Viking Stack-Rack Guide de configuration rapide

Aries

Aries 203015 Manuel utilisateur

Choetech

Choetech AT0005 Manuel utilisateur

ZZ2

ZZ2 ZZAIR-PRO Manuel utilisateur

Holman

Holman 4A80L Manuel utilisateur

Thule

Thule 2075 Manuel utilisateur

Motorola

Motorola T325 Manuel utilisateur

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guide d'installation

DV8

DV8 FBJL-02 Manuel utilisateur