Pure Pressure Longs Peak Manuel utilisateur
Pikes Peak V2
Longs Peak
User Manual R2.1
Table of Contents
1. Introduction
1.1. Warranty
1.2. What’s Included
1.3. Technical Specifications
1.4. Disclaimers & Safety Precautions
1.5. Uncrating Your Press
2. Press Setup
2.1. Vertical Orientation Setup
2.2. Horizontal Orientation Setup
2.3. Vertical Dual Pressure Installation
2.4. Horizontal Dual Pressure
Installation
2.5. Using Push Connect Fittings
2.6. Electrical Power
2.7. Compressed Air
3. Rosin Extraction Basics
3.1. Tips & Tricks
3.2. Yield and Material Types
3.3. Choosing Your Material
3.4. Filter Bag Preparation
4. Pressware Controls
4.1. Home Screen
4.2. System Settings
4.3. Quick Press
4.4. Last Run Data
4.5. Recipes Overview
4.6. Recipes Menu Options
4.7. Running Recipes
4.8. Saved Recipes List
4.9. Software Updates
5. Press Operation
5.1. Loading the Press
5.2. Pressure Control
5.3. Plate Speed Control
5.4. Pressing Material
6. Maintenance &
Troubleshooting
6.1. Common Issues
6.2. FAQ Part 1
6.3. FAQ Part 2
1. Introduction
From all of us here at PurePressure, thank you for your purchase!
Our rosin presses are engineered to last for many years with proper care.
The following user manual covers virtually every topic, including how to
use the press, technical specifications, tips on getting the most out of
your equipment, and much more.
Unless otherwise noted, the instructions contained in this manual apply to
both the Pikes Peak V2 and Longs Peak rosin presses identically and are
interchangeable.
720-446-9565
Sales Inquiries:
General Questions:
Technical Support:
purepressure.com
Contact:
We’re always here to help. Talk to us!
@gopurepressure
1.1 Warranty
PurePressure's rosin presses are built to last for many years with proper care. We want you to be satisfied with your equipment so if
there are ever any concerns, please do not hesitate to contact us. PurePressure guarantees the following warranty coverage for both the Pikes
Peak and Longs Peak rosin presses:
●2 year limited warranty against manufacturing defects for structural components (frame, truss and support legs) and pneumatic
cylinder.
●1 year limited warranty against manufacturing defects for the entire press including electronic and pneumatic components.
Warranty Replacements: In event of an approved warranty replacement or service, PurePressure will supply the necessary part(s) and special
tools, if needed. Shipping costs may be covered by PurePressure at its discretion.
Replacement Parts: Replacement parts for various components are available at reasonable prices for press owners directly from
PurePressure.
Exclusions: Warranty coverage eligibility will be determined by PurePressure and at PurePressure's sole discretion. PurePressure's
warranty obligations do not include (i) reasonable wear and tear; (ii) damage or corrosion caused by outdoor elements or outdoor use; (iii) use
of unapproved parts or unproved alterations to components; (iv) defects or damage caused by misuse, improper electrical power supply, or
compressed air inputs over 150 PSI (v) pneumatic components damaged from internal moisture or having been pressurized with compressed
air which is not clean or dry; (vi) vandalism, negligence, misuse or Force Majeure Events; or (vi) items expected to be consumed or expended
during the normal and routine operation and maintenance. This warranty is eligible for the original purchaser only and is not transferable.
Disclaimer: Except as expressly set forth in this Limited Warranty and to the greatest extent allowed by law, PurePressure makes no other
representations, warranties or conditions, express or implied, including any implied representations, warranties or conditions of
merchantability, fitness for a particular purpose, non-infringement, and non-interference.
Warranty Procedures: If your press is covered under the warranty period, please contact us with detailed information regarding the issue you
are experiencing so that we can get you operational as soon as possible. If you are experiencing a problem and are outside of the warranty
period, we will do everything in our power to get you affordable replacement component(s) in a timely manner. Please send all warranty and
replacement part related inquiries to [email protected]. All returned parts must be accompanied by an RMA number, which we
will supply.
1.2 What’s Included
What’s Included With Your Press
(items may differ depending on kit or model)
●LED capacitive touch screen
●Two button safety start
●Emergency-stop
●Plate speed actuation dial
●Compressed air filter / regulator(s)
●Pressure toggle for ramping
control
●Parchment clips
●Vertical orientation legs (qty 2)
●Horizontal orientation legs (qty 2)
●Leveling feet (qty 4)
●Industrial ¼” male air fitting
●Power cable
5 Tons of Force 8 Tons of Force
Pikes Peak V2
Longs Peak
1.3 Technical Specifications
Specification Pikes Peak V2 Longs Peak
Weight 120 lb 130 lb
Overall Dimensions
Depth x Width x Height
Horizontal: 29.2” x 19.7” x 13.5”
Vertical: 15.5” x 19.7” x 33.3”
Horizontal: 32.6” x 19.7” x 13.5”
Vertical: 15.5” x 19.7” x 36.8”
Power Requirement 120/240VAC
8A at startup / 2A continuous
120/240VAC
8A at startup / 2A continuous
Fuses (2x) Type: Fast Acting 250V
Current: 10A
Dimensions: 5mm x 20mm
Type: Fast Acting 250V
Current: 10A
Dimensions: 5mm x 20mm
Compressed Air Requirements PSI: 10 - 120
CFM: 1.7 or greater
Dry clean air
PSI: 20 - 140
CFM: 2.2 or greater
Dry clean air
Pneumatic Cylinder Maximum Force
Output
9,876 lb @ 120 PSI 15,300 lb @ 140 PSI
Frame & Enclosure Metal A36 Steel A36 Steel
Heat Plates Sizes: 10” x 3”
Material: 6061 Aluminum
Maximum Temperature: 300 °F
Sizes: 10” x 3”
Material: 6061 Aluminum
Maximum Temperature: 300 °F
1.4 Disclaimers & Safety
Precautions
WARNING: PUREPRESSURE, LLC IS NOT RESPONSIBLE FOR INJURY OR LOSS DUE TO IMPROPER USE OF EQUIPMENT.
DISCLAIMER: COMPRESSED AIR SOURCE REQUIRED. MAX ALLOWABLE WORKING PRESSURE 140PSI. THIS PRODUCT OPERATES
UTILIZING A PNEUMATIC CYLINDER.
DISCLAIMER: YOUR PRESS SPEED VALVE IS TURNED OFF FOR SHIPPING. THE DIAL MUST BE OPENED TO OPERATE YOUR PRESS
PNEUMATIC.
DISCLAIMER: CONNECTING TO ANY OTHER POWER SOURCE OTHER THAN WHAT YOUR PRESS IS RATED FOR ON ITS SERIAL LABEL
WILL VOID YOUR WARRANTY.
WARNING: EXCEEDING 150PSI ON YOUR PRESS WILL TERMINATE YOUR WARRANTY. A MECHANICAL BLOW OFF VALVE WILL
EXHAUST AND YOUR FIRMWARE WILL DETECT THE OVERPRESSURE FAULT.
WARNING: ONLY USE THE DESIGNATED AC POWER PLUG PROVIDED WITH YOUR PRESS. USING ALTERNATE VOLTAGES OTHER THAN
SPECIFED CAN RESULT IN DAMAGE TO YOUR UNIT.
WARNING: IF THE HEAT PLATE ICON ON YOUR SCREEN IS RED THEN THE PLATES ARE HOT ENOUGH TO CAUSE BURNS.
WARNING: HEAT PLATES CAN CAUSE SERIOUS BURNS. NEVER PLACE FOREIGN OBJECTS, FINGERS, HANDS OR OTHER BODY PARTS
ON OR BETWEEN THE HEAT PLATES.
WARNING: PINCH POINT CAN CAUSE SERIOUS INJURY. NEVER PLACE FOREIGN OBJECTS, FINGERS, HANDS OR OTHER BODY PARTS
ON OR BETWEEN THE HEAT PLATES.
WARNING: ALWAYS WEAR EYE AND EAR PROTECTION AS WELL AS HEAT RESISTANT GLOVES FOR SAFE OPERATION.
WARNING: PARCHMENT CLIPS ARE NOT HANDLES. DO NOT USE TO LIFT THE PRESS.
WARNING: EMERGENCY STOP BUTTON - YOU MAY CANCEL THE OPERATION AT ANY POINT BY PRESSING THE EMERGENCY STOP
BUTTON. THIS WILL DISPLAY EMERGENCY STOP ON THE LED TOUCH SCREEN AND WILL CUT POWER TO THE HEATERS WHILE
RETRACTING THE AIR CYLINDER. NOTE: AN INLET AIR SUPPLY OF AT LEAST 10 PSI IS REQUIRED FOR THE CYLINDER TO RETRACT.
DISCONNECTING THE AIR SUPPLY PRIOR TO PRESSING THE EMERGENCY STOP BUTTON WILL NOT RETRACT THE PRESS. TO CLEAR
THE EMERGENCY STOP, TWIST THE BUTTON TO RELEASE. THIS WILL REBOOT THE SYSTEM AND RETURN YOU TO THE MAIN MENU.
THE HEATERS WILL BE OFF AT THIS POINT.
WARNING: DO NOT PRESS ANYTHING OTHER THAN SOFT PLANT MATERIALS IN THE PIKES PEAK, PIKES PEAK V2, OR LONGS PEAK
PRESS. PRESSING OTHER OBJECTS WILL VOID THE WARRANTY.
WARNING: WHEN USING ISOPROPYL ALCOHOL TO CLEAN THE HEAT PLATES THE POWER SHOULD BE DISCONNECTED, AND THE
HEAT PLATES SHOULD BE AT ROOM TEMPERATURE. ALWAYS WEAR GLOVES AND EYE PROTECTION.
1.5 Uncrating Your Press
Steps to Safely Uncrate Your Press
Note: Use two people to lift the press safely.
1. Using a Phillips screwdriver or power tool,
remove wood screws from top lid. (Figure 1A)
2. Lift off crate cover.
3. Remove contents from top section and remove
crate shelf. (Figure 2A)
4. Remove the loose foam packing blocks around
the press (some foam blocks are glued to the
crate itself - do not remove them).
5. Using the two straps around the press pull
straight up to remove the press from the crate
and set on a sturdy table. (Figure 3A)
6. Remove the plastic wrapping and set your Dual
Pressure kit as well as your vertical legs aside.
7. Turn your emergency stop button clockwise to
release.
8. Turn your Speed Controller knob a few turns
counter clockwise to open the valve. This will
allow the plates to fully actuate.
Figure 1A
Figure 4A
Figure 2A
2. Press Setup
Vertical vs. Horizontal Orientation
Most users will encounter greater utility and productivity using the Pikes Peak V2 or Longs Peak rosin press in the vertical orientation.
This is because loading and unloading bags and parchment tends to be easier. It is our recommendation that you become familiar
with the press in the vertical orientation first, and then move to the horizontal orientation if desired.
For horizontal orientation pressing, virtually any of our silicone products or parchment paper works well as a collection surface.
Note: Your press comes set up in
the horizontal orientation for shipping
purposes.
2.1 Vertical Orientation Setup
Vertical Orientation Setup
Warning: HEAVY EQUIPMENT! Two people
recommended for setting up the press vertically or
horizontally.
1. The vertical orientation requires the two triangular
shaped legs. To change to the vertical orientation from
the default horizontal orientation, carefully bring the two
front legs off the edge of a table while ensuring the press
will not fall forward. (Figure 1A)
2. Using a ¼” Allen wrench or bit, remove the (qty4)
screws securing the horizontal legs as well as the (qty2)
adjacent screws just above them. Remove legs on both
sides. (Figure 2A)
3. Line up each vertical triangular leg to the three blank
holes on the side of the frame and then replace the (qty
3) screws on each side. (Figure 3A)
4. Then, fasten leveling feet into place, and lift the press
into the full upright vertical orientation.
5. Place the touchscreen display enclosure to the recessed
position so it is flush with the front of the press.
Figure 2A
Figure 1A Figure 3A
Vertically Oriented Pikes Peak
Ce manuel convient aux modèles suivants
1
Table des matières
