PT M705 Manuel utilisateur

OWNER'S MANUAL

WARNING: READ, UNDERSTAND AND

FOLLOW ALL INSTRUCTIONS AND

WARNINGS BEFORE OPERATING THIS

TOOL. FAILURE TO DO SO MAY RESULT

IN PERSONAL INJURY AND/OR

PROPERTY DAMAGE AND WILL VOID

WARRANTY.

H.V.L.P. TOUCH-UP SPRAY GUN

Item Number M705

SPECIFICATIONS

Specifications are subject to change without notice

IMPORTANT SAFETY INFORMATION



WARNING! READ, UNDERSTAND AND FOLLOW ALL INSTRUCTIONS AND WARNINGS BEFORE OPERATING THIS TOOL.

FAILURE TO DO SO MAY RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE AND WILL VOID WARRANTY.

Air Pressure:..................................... 34 - 43 P.S.I.

Spray Pattern:..............................................3-4 in.

Spray Head & Needle:...............................1.2 mm

Cup Capacity:............................................. 200 cc

1. Keep work area clean. Cluttered areas invite injuries.

2. Observe work area conditions. Do not use machines or power

tools in damp or wet locations. Don’t expose to rain. Keep

work area well lighted. Do not use electrically powered tools

in the presence of ammable gases or liquids. Always keep

work area free from obstructions and well ventilated.

3. Keep children away. Children must never be allowed in the

work area. Do not let them handle machines, tools, hoses or

extension cords.

4. Store idle equipment. When not in use, tools must be stored

in a dry location to inhibit rust. Always lock up tools and keep

out of reach of children and other untrained persons. Switch

o all unused electrical tools when stored. Tools are danger-

ous in the hands of untrained users.

5. WARNING! All persons in the work area must always

wear approved eye and ear protection and approved

breathing apparatus when this spray gun is in operation.

6. Work Safe. Do not wear loose clothing or jewelry that could

become caught by moving parts, causing injury. Operate tool

a safe distance from yourself and others in the work area.

Keep proper footing and balance at all times. Do not reach

over or across running machines, hoses, etc.

7. Stay alert. Watch what you are doing, use common sense. Be

sure all personnel are clear of the direction of the spray gun.

Do not operate any tool when you are tired.

8. Do not operate any tool if under the inuence of alcohol or

drugs. Read warning labels on prescriptions to determine if

your judgment or reexes are impaired while taking drugs. If

there is any doubt, do not operate any tool.

9. Never aim spray gun at anyone. Do not spray near sparks,

open flame, lit cigarettes, pilot lights, space heaters or any other

potential ignition source. DO NOT SMOKE IN WORK AREA.

10.Follow air source manufacturers directions for connection of

regulators, lters, and other accessories to air source. Do not

install quick couplers directly on tool as they put unnecessary

strain on the air inlet threads possibly causing them to wear

out prematurely. Instead, install them on a short length of air

hose attached to the tool.

Avg. Air Consumption (CFM):...........................3.1

Fluid Inlet (NPS): ...................................M14 x 1.0

Air Inlet (NPS):.............................................1/4 in.

Hose Size (ID): ............................................3/8 in.

11.Follow manufacturers instructions and safety information to

ensure safe handling and proper use of paints, lacquers, thin-

ners, base coats, etc. Do not use latex or other heavy paints.

They are not recommended for this spray gun.

12.Always disconnect spray gun from air source before

disassembly.

13.

WARNING! Solvents 1,1,1-Trichloroethane and Methylene

Chloride (Dichloromethane - sometimes called Methylchloride)

can chemically react with the Aluminum used in most spray

equipment creating an explosion hazard. Read the label or

data sheet from the material you intend to spray. NEVER use

any material containing these solvents. If unsure as to the

composition of your material, check with your supplier. Do not

use acids for cleaning.

14. Check for damaged parts. Before using any tool, any part that

appears damaged should be carefully checked to determine

that it will operate properly and perform its intended function.

Check for alignment and binding of moving parts; any broken

parts or mounting xtures; and any other condition that may

aect proper operation. Any part that is damaged should be

properly repaired or replaced by a qualied technician.

15. Maintenance. For your safety, maintenance should be

performed regularly by a qualied technician using original

PERFORMANCE TOOLS® replacement parts. Failure to do so

can lead to accidents for the operator. Use of any other parts

will void the warranty. Only use accessories intended for use

with this tool. Approved accessories are available from Per-

formance Tool®. Use only accessories that are recommended

by the manufacturer for your model. Accessories that may be

suitable for one tool may become hazardous when used on

another tool.

WARNING!

The warnings, cautions, and instructions discussed

in this instruction manual cannot cover all possible conditions and

situations that may occur. It must be understood by the operator

that common sense and caution are factors which cannot be built

into this product, but must be supplied by the operator. Read and

understand all of the instructions provided in the instruction manual

of this product, as well as, any other tool (s) used with this product.

This instruction manual is intended for your benefit. Please read and follow the safety, installation, maintenance and troubleshooting steps

described within to ensure your safety and satisfaction. The contents of this instruction manual are based upon the latest product information

available at the time of publication. The manufacturer reserves the right to make product changes at any time without notice.



WARNING: Read and understand this entire instruction manual before attempting to assemble, install, operate or maintain this product.

Failure to comply with the instructions may result in serious personal injury and/or property damage!

The following signal words are used to emphasize safety warnings that must be followed when using this product:

DANGER:

Indicates an imminently hazardous situation

that, if not avoided, WILL result in death or serious injury.

WARNING:

Indicates a potentially hazardous situation that,

if not avoided, COULD result in death or serious injury.

CAUTION:

Indicates a potentially hazardous situation that,

if not avoided, MAY result in minor or moderate injury.

NOTE: Indicates important information, which if not

followed, MAY cause damage to equipment.

SAFETY GUIDELINES / DEFINITIONS

Step 3: Spray Pattern Controls

Pattern Shape - The shape of the spray can be adjusted

from a round pattern to a flat pattern by turning the Pattern

Control Knob. Turning knob in rounds the pattern, turning

knob out flattens the pattern.

Pattern Orientation - A flat or semi-round spray pattern

can be adjusted to any angle from horizontal to vertical by

turning the Air Nozzle. Pattern is perpendicular to “ears”

on nozzle. That is, when the ears are horizontal, the spray

pattern will be vertical and when the ears are vertical the

spray pattern will be horizontal.

Step 2: Air and Fluid Volume Controls

These two controls are used in conjunction with each other

to accurately adjust air/uid (Paint) ratio and will vary for

dierent paints. Changing one control Fluid Volume aects

the other so alternating back and forth between them to

ne tune your adjustment will yield optimum results.

Air Volume Control - Air volume is adjusted by turning the

Air Fluid Volume Control Knob. Turning knob in reduces

volume, turning knob out Control Knob increases volume.

Fluid Volume Control - Fluid volume is adjusted by

turning the Fluid Volume Control Knob. Turning knob in

decreases volume, turning knob out increases volume.

Once a satisfactory volume is set, you can lock the

adjustment by turning the lock nut in tight.

OPERATION

Step 1: Inlet Air Pressure Regulation

Assemble components of spray gun and connect to

clean air source as described above. Clean air source

is imperative to ensure peak performance. The use of

an in-line air lter is highly recommended to keep any

contaminants from entering the spray gun. Set inlet air

pressure to between 40 and 45 P.S.I. to begin adjustments.

(This is a good operating inlet pressure suitable for most

applications, however, depending on materials being

sprayed and other external factors such as temperature,

humidity, etc., you may need to come back to this step and

increase or decrease pressure as needed after attempting

adjustments in step 2.)

Inlet pressure is adjusted by turning the Pressure Regulator

Control Knob. Knob must rst be pulled out to unlock.

Turning knob clockwise increases pressure, turning knob

counter-clockwise decreases pressure. Once desired

pressure is reached, push the knob back in to lock.

CARE & MAINTENANCE

WARNING! Clean gun before and after each use.

To protect the precision machined internal parts and

ttings in this gun from corrosion during shipping, some

oils or other corrosion resistant agents may have been

applied. It is important to remove any such residue before

attempting to use the gun. To clean, place a small amount

of appropriate thinner into paint cup and spray through

gun while pulling and releasing trigger repeatedly. Wipe

exterior of gun, nozzles and paint cup. In some cases,

if the gun becomes clogged, disassemble completely

and soak all parts in thinner. After soaking, use wire and

cleaning brush to clear small internal passages. Check and

clean paint cup lter. Replace if worn.

A clean air source is imperative to ensure peak

performance. The use of an in-line air lter is highly

recommended to keep any contaminants from entering

the spray gun. Inspect all ttings and hardware to ensure

proper seating. Be sure air line ttings are tight with no

leaks. Replace any worn parts as necessary.

Check needle and nozzles for nicks, scratches or burrs.

Any such conditions will seriously impair performance.

Replace as necessary.

Regulated air out

to Spray Gun

Unregulated

air Inlet

Pressure Regulator

Control Knob Locked

Pressure Regulator

Control Knob Unlocked

Air

Nozzl

Spray Pattern

Control Knob

Fluid Volum

Control Knob

Fluid Volum

Lock Nut

Air

Volume

Control Knob

REPLACEMENT PARTS LIST

Call Customer service for replacement parts: 1-800-497-0552

REPLACEMENT PARTS LIST

# Description Qty. # Description Qty.

1. Gun body.......................................................... 1

2. O-ring 20 x 1.5.................................................. 1

3. Sealing Gasket ................................................. 1

4. O-ring 2 x 1.5.................................................... 1

5. Fluid packing nut .............................................. 1

6. Air Isolation Ring............................................... 1

7. Material Nozzle ................................................. 1

8. Locking Ring..................................................... 1

9. Air Nozzle Washer ............................................ 1

10. Locking Knob ................................................... 1

11. Air Cap.............................................................. 1

12. Air Valve Spring ................................................ 1

13. Air Valve Sealing Gasket................................... 1

14. Needle Valve ..................................................... 1

15. Air Valve Body .................................................. 1

16. O-ring 8 x 1.5.................................................... 1

17. Air Valve Sealing Screw .................................... 1

18. E-Clip................................................................ 1

19. E-Clip................................................................ 1

20. Trigger............................................................... 1

21. Trigger Pin......................................................... 1

22. Trigger Pin......................................................... 1

23. Air Inlet Bushing ............................................... 1

24. Air Valve Spring ................................................ 1

25. Gasket .............................................................. 1

26. O-ring 2.5 x 1.8................................................. 1

27. Air Valve Control Stem...................................... 1

28. Air Flow Control Knob ...................................... 1

29. Air Inlet Bushing ............................................... 1

30. E-Clip................................................................ 1

31. Spray Control Nut............................................. 1

32. Spray Regulator Screw..................................... 1

33. Pattern Control Knob........................................ 1

34. Screw................................................................ 1

35. O-ring 6 x 1.5.................................................... 1

36. Bearing ............................................................. 2

37. Needle .............................................................. 1

38. Needle Seat ...................................................... 1

39. Needle Spring................................................... 1

40. Needle Adjusting Seat ...................................... 1

41. Needle Adjsuting Screw ................................... 1

42. Sealing Gasket ................................................. 1

43. Paint Cup Coupler ............................................ 1

44. Cup Filter .......................................................... 1

45. Sealing Gasket ................................................. 1

46. Connecting Nut ................................................ 1

47. Gasket .............................................................. 1

48. Paint Cup.......................................................... 1

49. Connecting Screw ............................................ 1

50. Paint Cup Lid.................................................... 1

TROUBLESHOOTING

WARNING! - Disconnect spray gun from air source before making adjustments

NOTE: Problems listed above with more than one solution may have a combination of causes. Please be sure that all

solutions listed for each problem have been checked to eliminate possibility of further trouble. Sometimes solutions may

need to be repeated for best results.

Half-Moon Shaped Pattern

This is usually caused by clogged

air holes on the Air Nozzle ears.

1. Clean, tighten or replace

2. Clean, tighten or replace

Problem: Probable Cause: Solution:

Your spray gun was constructed with quality materials

and workmanship and will give you many years of trouble

free use when cared for as described in the "Care and

Maintenance" section on page 3. However, as with any

mechanical device, periodic adjustments are necessary to

maintain a peak level of performance. Should your spray

gun be displaying any of the following symptoms, the

simple procedures shown below will correct the problem.

Irregular or Offset Pattern

This can be caused by

1. A dirty or damaged Needle tip

or Fluid Nozzle

2. Clogged atomization holes on

Air Nozzle around the center

Spitting

1. Too little material in cup

2. Loose Fluid Nozzle

3. Damaged Needle Packing

4. Dirty or damaged Needle & Nozzle Set.

Carefully clean out holes with

wire after soaking in thinner.

1. Clean or replace Needle

or Fluid Nozzle.

2. Clean Air Nozzle

1. Refill cup

2. Tighten Nozzle

3. Replace Packing

4. Clean or replace parts

Material in cup bubbles or “Boils”

1. Loose, clogged or damaged Fluid Nozzle

2. Loose, clogged or damaged Air Nozzle

1 YEAR WARRANTY

PERFORMANCE TOOL® extends only the following warranties, and only to original retail purchasers. These warranties give specific legal rights.

Except where prohibited by local law, the law of the State of Washington governs all warranties and all exclusions and limitations of warranties and

remedies. There may be other rights which vary from state to state.

PERFORMANCE TOOL® warrants the product to be free from defects in materials and workmanship under normal use and service. A defective

product may be returned for a free replacement within 90 days from the date of purchase, provided that product is returned to place of purchase

immediately after discovery of defect. After 90 days and up to one year from date of purchase, PERFORMANCE TOOL® will replace at no charge

any parts which our examination shall disclose to be defective and under warranty. These warranties shall be valid only when a sales receipt

showing the date of purchase accompanies the defective product or defective part (s) being returned. For part (s) after 90 days, please remit your

request, postage prepaid to:

PERFORMANCE TOOL, P.O. Box 88259 Tukwila, WA 98138

These warranties exclude blades, bits, punches, dies, bulbs, fuses, hoses, and other consumables which must be replaced under normal use and

service. These warranties shall not apply to any product or part which is used for a purpose for which it is not designed, or which has been repaired

or altered in any way so as to affect adversely its

performance or reliability, nor shall these warranties apply to any product or part which has been subject to misuse, neglect, accident or wear and

tear incident to normal use and service.

PERFORMANCE TOOL® does not authorize any other person to make any warranty or to assume any liability in connection with its products.

Except for warranties of title and the limited express warranties set forth above, PERFORMANCE TOOL® makes no express or implied warranties

of any kind with respect to its products. In particular, PERFORMANCE TOOL® makes no implied warranty of merchantability and no implied

warranty of fitness for any particular purpose, except that for goods purchased primarily for personal, family or household use and not for

commercial or business use, PERFORMANCE TOOL® makes an implied warranty of merchantability (and, if otherwise applicable, an implied

warranty of fitness for a particular purpose), but only for the particular qualities or characteristics, and for the duration, expressly warranted above.

The laws on limitation of implied warranties may differ from state to state, so the above limitations may not apply in all cases.

PERFORMANCE TOOL® shall not be liable for consequential, incidental or special damages resulting from or in any manner related to any product,

or to the design, use, or any inability to use the product. The sole and exclusive remedy for a defective product or part shall be the repair, or

replacement thereof as provided above. The laws on limitation of remedies or on consequential, incidental or special damages may vary from state

to state, so the above limitations may not apply in all cases.

Table des matières

Autres manuels PT Pistolet à peinture

PT M708 Manuel utilisateur

PT M503 Manuel utilisateur

Manuels Pistolet à peinture populaires d'autres marques

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Manuel utilisateur

Graco

Graco 246737 Manuel d'utilisation et d'entretien

Binks

Binks SV100 Manuel utilisateur

Fimco

Fimco LG-4-3-1 Manuel utilisateur

AG SPRAY

AG SPRAY FS-ATV-25BL Manuel utilisateur

Nordson

Nordson MicroMax 2 Manuel utilisateur

Bonide

Bonide 051 Manuel d'utilisation

zogics

zogics Z-DAS Manuel utilisateur

KISANKRAFT

KISANKRAFT KK-KBS-165 Manuel utilisateur

Matrix

Matrix SG 650 Manuel utilisateur

Anest Iwata

Anest Iwata SGA-3 Guide de démarrage rapide

paasche

paasche VV Fiche technique

Carlisle

Carlisle DeVilbiss JGA-510 Manuel utilisateur

Gardena

Gardena 11120 Manuel utilisateur

Conrad

Conrad Hobby Airbrush K3 Manuel utilisateur

wiwa

wiwa 14025 R/F Manuel utilisateur

Graco

Graco EM 390 Manuel d'utilisation

DeVilbiss

DeVilbiss LUNA2i Manuel utilisateur