Menu List Menu Items
Correct Card Orientation
Swipe Card
Through in
Either Direction
5Confgure Carrying Strap
(if necessary)
Optional MCR Module
Menu Navigation
Enter Setup
Menu
Follow instructions for printing test page. The end of the test page
printout includes a prompt to press the feed button to enter setup.
Select/Change Menu choices will print out. To select (enter) a menu or change the
most recently printed item, press the power button.
Go To Next At any level in the menu structure, press the feed button to go to the
next item.
Exit Menu Hold
1 sec
Shortcut - Exit from a menu and go to the next menu OR
Exit and Save Changes (if changes have been made).
Power Off
(from setup
menu)
Hold
2 sec
Shortcut - To turn the printer on in setup mode and discard any menu
changes, press and hold the power button for 2 seconds.
Menu Structure
Interface Menu Emulation, Print Interface Settings
For Serial Interface:
Baud Rate, Parity, Data Bits, Stop Bits, RTS/CTS, XON/XOFF
For Bluetooth Interface:
Pairing Mode, Security, Role Policy, Discoverability
For Wi-Fi Interface:
Wi-Fi Default Peer-to-Peer (for more info see operators manual)
Format Menu Font, Left Margin, Right Margin, Print Contrast, Max Paper Speed, FFeed Distance
When Using Mark Sensing:
Mark Sensitivity, Top Of Form Adj, Tearbar Adjust
Print All Logos in Memory Select to print graphic files loaded in flash memory
Options Menu Left Paper Guide, Rt. Paper Guide, Auto Power Down, Print Promo, Print Header
Hardware Menu Enter HEX DUMP Mode, Reset to Factory Defaults
Exit Menu Discard Changes Select to exit the menu without saving
Exit Menu Save Changes Select to exit the menu while saving
Tips The menus are cyclical and will return to the top of the list after the last item in each menu level.
The on-board menu is for convenience. Use the Psion Setup Utility when possible.
For more information on menus, see the operator’s manual.
Symbol LED
StateIndicates Cause
Power Off
Printer turned offOR no power available
Power On Printer turned on, normal operating state
Printer Standby Printer in standby mode (will wake with data)
edomputesnisiretnirpROatadgniviecerretnirPysuBretnirP
ChargingBattery is receiving charge from external power
Battery Low Battery charge is low, printer is in standby mode
Battery Low Battery charge is low, printer is in normal operating
state
Paper Door Open Paper door is open, preventing paper
feed
Paper Out Fault Paper roll empty or paper not fed
properly
Communication
Fault
Problem receiving data. Turn off
printer to reset
LED
LED Off
LED On (Illuminated)
LED Slow Blink
LED Rapid Flash
Audible Tone
If illuminated, indicates
ready for swipe.
Left Paper
Guide
1
2
4Install Second Paper Guide
(not necessary for standard 4” roll)
Snap front
into numbered
slot
To use the PRINTABOUT for
printing on Psion standard
3” paper (3.125” wide),
insert the second paper
guide in slot 7. This will left-
align the roll.
In the Options menu, set the
“Rt. Paper Guide” setting to 7.
This will insure test pages print
and margins are measured
correctly.
For paper rolls less than 4”
wide that are not standard
Psion rolls, consult the
operators manual for more
instructions on proper
installation and configuration.
The carrying strap may be converted to a belt loop or connected to
our Shoulder Strap: Accessory (PN 33020) sold separately.
Shoulder Strap Attachment
Belt Loop Conversion
Detach the carrying strap, thread through
the opening on the triangular end of the
shoulder strap, and re-attach the inside
NOTE: Application software must be capable of
capturing the magnetic card data transferred from the printer.
See Programmer’s Manual for further information.
PRINTABOUT On-Board Menu
Control Indicators
Detach the carrying strap, thread behind and over belt, and re-attach using
the two outside Velcro pads provided.
TM
Velcro pads.
TM
Quick Start Guide
(cont.)
Right Paper Guide
in First
Snap Tail
Key:
State
MCR Status Indicator LED
