Prorack P15 Manuel utilisateur

K427

Fitting Kit

EN Fitting Instructions for Basic Carrier

x 4 x 4 x 2 x 1

x 1 x 1 x 2 x 2

x 4

Revision No: 6F 1

Fitting Kit EN

K427

First Time Installation

●Remove parts from inside the package and

check. Contact your dealer if any parts are

missing or damaged.

●This kit fits type A, B, C and D.

●These instructions show type A crossbar

fitted. They also apply to type B, C and D.

NOTE: Clamp images in these instructions may

not be representative of the clamps in this kit

Fitting Kit EN

K427

●Use keys to remove covers.

●Use hex screwdriver to reverse adjusting

screw 10 turns.

●Press adjusting screw and pull crossbar

legs out. Refer to the crossbar instructions

for crossbar adjustment method.

●Ensure each end of the crossbar is

adjusted equally.

Fitting Kit EN

K427

●Adjust crossbar in or out to suit vehicle.

Refer to the crossbar instructions for

crossbar adjustment.

●Please check the front of this manual for

information relating specifically to your

vehicle.

●Remove locking screw.

●Apply protective strip as shown.

Trim if required.

Fitting Kit EN

K427

●Letters refer to the part numbers stamped

on clamps.

●Clamp Part Number:

A = 545A

B = 546B

C = 547B

●NOTE: REAR CROSSBAR ONLY

●Attach clamp to each leg. NOTE; clamps

may have labels showing their positions on

the vehicle (For example; "Front Right").

●The rear crossbar secures directly to the

edge of the roof above the rear window.

●Fit rubber pads (supplied with fitting kit) to

foot.

●Make sure the pad fits into the holes

underneath the foot.

●Repeat for all legs.

Fitting Kit EN

K427

Fitment

●Place crossbar on vehicle. Minimum

recommended spacing between the bars is

700mm (27 1/2") (unless otherwise stated).

●Please check the front of this manual for

information relating specifically to your

vehicle.

●NOTE: FRONT CROSSBAR ONLY

●Remove plastic clamp block by gripping bar

leg with fingers and push firmly with

thumbs until clamp block drops out behind

leg.

●To install the front crossbar, pull back top

rubber door seal. Locate threaded inserts

under black spots above the front doors.

●Put front clamp in place. Refit the clamp

block over clamp. Refit locking screw,

ensuring end of screw inserts in the hole on

the clamp.

Fitting Kit EN

K427

●Fit a fibre washer on each capscrew and

attach front clamps to the vehicle body.

●Refit rubber seal over the clamp.

●Adjust the legs on the crossbar so that they

are positioned equally from the ends of the

crossbar, and the clamps engage firmly on

the body work of the vehicle.

●Tighten adjusting screw to 5 Nm (3.7 ft lb)

hand tight.

●Repeat for all four positions.

Fitting Kit EN

K427

●Progressively tighten the clamp block

locking screws alternating from one side of

the vehicle to the other to tension evenly.

●Check crossbar is securely attached to the

vehicle.

●Use keys to fit and lock covers

CAUTION: Recheck all fasteners immediately after

a load is applied to the crossbars.

Regularly check screws are tight.

Fitting Kit EN

K427

Maintenance

●Clean the car roof and surfaces of the

product that will be in contact with the car

roof.

●Follow the fitting instructions for fitting the

product to your vehicle. Make sure all steps

are carried out in order.

●Set crossbars a minimum distance of

700mm (27 1/2") apart where no other

distance is specified in the fitting

instructions. This is especially important

when carrying long loads.

●Check unit is securely attached whenever

you refit it to the vehicle. If the unit feels

loose, refer to the fitting instructions and

readjust.

●Some glass/panoramic roofs and radio

antennae may not be able to be used when

the product is fitted.

●Do not modify this product.

●Refer to the maximum permitted load

capacity specified in the fitting instructions.

Do not exceed the vehicle manufacturers

roof load rating if it is lower than the

maximum load capacity specified in the

fitting instructions.

●Loads should not overhang the sides of the

product and be evenly distributed with the

lowest possible centre of gravity.

●Long loads should be secured with non-

elastic straps to the front and rear of the

vehicle.

●Objects with pointed ends (e.g. ski poles)

should be carried with the pointed ends to

the rear of the vehicle.

●Remove all loose or removable objects

from the load prior to loading.

●Make sure all loads are securely fastened

with non-elastic straps. Check regularly

during longer journeys.

●A loaded roof rack system can alter the

performance of your vehicle. Be especially

aware of the effects of side winds,

changing of direction, and braking

performance. Avoid rapid acceleration and

deceleration. Drive carefully.

●Note that the total height of the vehicle

increases when upright loads are carried.

●Products should be locked during transport

if they have locks fitted.

Fitting Kit EN

K427

●Check and replace worn out or defective

parts.

●Keep the product clean and maintained.

●Never drive into a car wash with the roof

rack system fitted.

●Lubricate locks and adjusting screws at

regular intervals.

●Remove the products from the vehicle

when not in use. Make sure all loose parts

are stored safely.

●Yakima Australia Pty Ltd

17 Hinkler Court

Brendale QLD 4500

AUSTRALIA

www.prorack.com.au

www.prorack.co.nz

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Prorack Accessoires automobiles

Prorack

Prorack K317 Manuel utilisateur

Prorack

Prorack K857 Manuel d'utilisation et d'installation

Prorack

Prorack K838 Manuel utilisateur

Prorack

Prorack K919 Manuel utilisateur

Prorack

Prorack K536 Manuel utilisateur

Prorack

Prorack K038 Manuel utilisateur

Prorack

Prorack K501 Manuel utilisateur

Prorack

Prorack K1007 Manuel utilisateur

Prorack

Prorack K453 Manuel utilisateur

Prorack

Prorack K426 Manuel utilisateur

Prorack

Prorack K1001 Manuel utilisateur

Prorack

Prorack K1013 Manuel utilisateur

Prorack

Prorack K327 Manuel utilisateur

Prorack

Prorack K136 Manuel utilisateur

Prorack

Prorack K188 Manuel utilisateur

Prorack

Prorack K068 Manuel utilisateur

Prorack

Prorack K335 Manuel utilisateur

Prorack

Prorack K102 Manuel utilisateur

Prorack

Prorack K347 Manuel d'utilisation et d'installation

Prorack

Prorack K379 Manuel utilisateur

Prorack

Prorack K1215 Manuel utilisateur

Prorack

Prorack VOYAGER PR3207 Manuel utilisateur

Prorack

Prorack K455 Manuel utilisateur

Prorack

Prorack K548 Manuel utilisateur

Manuels Accessoires automobiles populaires d'autres marques

James Baroud

James Baroud Odyssey Manuel utilisateur

Motorola

Motorola i50sx Manuel utilisateur

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manuel utilisateur

Feniex

Feniex T3 Manuel utilisateur

Renault

Renault 77 11 423 180 Manuel utilisateur

Kia

Kia E8300-4D000 Manuel utilisateur

Brink

Brink 756843 Manuel utilisateur

Whispbar

Whispbar K085W Manuel utilisateur

v.link

v.link CI-VL2-PC-HSD Manuel utilisateur

Viking

Viking Stack-Rack Guide de configuration rapide

Aries

Aries 203015 Manuel utilisateur

Choetech

Choetech AT0005 Manuel utilisateur

ZZ2

ZZ2 ZZAIR-PRO Manuel utilisateur

Holman

Holman 4A80L Manuel utilisateur

Thule

Thule 2075 Manuel utilisateur

Motorola

Motorola T325 Manuel utilisateur

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guide d'installation

DV8

DV8 FBJL-02 Manuel utilisateur