47
6. User's Guide
6.1 Receiver
USER'S GUIDE
1. Install attachedtwo BNC antennason the antennajack at therear panel of the
receiver. Inclineantennas outwards 45degree to getthe best reception.
2. To get thebest reception, install receiver at least1 metre abovethe ground. Keep
transmitter at least1 meter fromreceiver antennas andfar away frominterferential
sources.
3. Use attachedmounting rack toinstall receiver onEIA standardrack.
4.
5. AFoutput: Insert oneend of thesignal cable intoAF outputjack (8) or(9) at the
back of thereceiver and theother end ofthe signal cableinto amplifier ormixer
MIC-IN jack.
6. Turnon power switch(1), LCD will light and showthe group and channel number
set at lastusing time.
7. Press GPbutton (2), GPLED (4) willlight; release theGP button, GPLED will
extinguish. Press CHbutton(3), CH LEDindicator(5) will light;release the CH
button, CH LEDwill extinguish.
8. Group adjust:Press GP button(2) for about3 seconds, GPnumber on LCDwill
flash, frequency willalso flash; releaseGP button(2), nowGP button changesto
UP function andCH button changesto DOWN function,press GP button to move
GP UPor CH buttonto move GPdown.
9. Channel adjust: Press CH button(3) for about3 seconds, CH number on LCD
will flash, frequencywill also flash;release CH button(3),press GP button to move
CH UP or CH buttonto move CH down.
10. Afteradjusting Group andChannel, release all buttons, group orchannel will
flash about 3seconds and thenstop, frequency willbe locked andsaved.
11. Adjust receiverGP and CHto be same as transmitter GPand CH (
, receiver LCDwill showAF signal strength,RF signal
strength and RF Aor RF B reception.( These informationwill not showwhen
adjusting GP orCH, transmitter isnot turned on,or GP and CH oftransmitter is
different from receiver.)
Note: This system has 16sets of presetfrequencies (from 00to 0F) whichwill not
interfere each other. Users are suggested to usethese frequencies firstly.
Choose other frequenciesif more frequenciesare needed.
Plug one endof theAC power adapterinto ACpower source withspecified voltage
and the otherend into DCINPUT connector (10)on the backof receiver.
according to
the above procedure7,8,9)
6.2 Handheld Microphone
5. Features
1. UHF PLLsynthesized circuit, with256 selectable frequenciesfor choice.
2. Truediversity receiving modecan effectively avoid drop-outs anddead spots.
Available distance can bemore than 100 metre.
3.
4. Adopthigh stable circuitdesign and spareparts, this devicecan be operatedin
a wide rangeof temperature environment(-10 ~+60 ). AdvancedVCO circuit
design to allowperformers shout loudlywithout any brokenvoice happen. Itis the
best microphone systemfor stage performance.
5. Using highsensitivity, wide frequency response dynamic cartridge andadvanced
signal processing circuitto present thereal and natural voice of bothmale and
female. It isthe top choicefor live-performance singers.
6.
7. High performancecartridge. Following isfrequency response figure.
With special anti-interferencecircuit and tonecode security toeffectively avoid
interference and eliminatenoise.
Numeric LCD is clear and accuratein displaying receiving channel, receiving
signal level andAF signalstrength.
8. International EIAstandard half Urack. Metal case.Strong and nice.
9. Pre-programmed 16groups of frequencyto be usedsimultaneously without any
interference, including 00,01,02,03,04,05,06,07,08,09,0A,0B,0C,0D,0E,0F.
10. Pre-set twogroups of frequenciesfor choice. Oneis for USAstandard, another
is for Europestandard. Following isfrequency list.
X:1000Hz Y:-59.3dBV/Pa
Y:-57.1dBm/Pa
D:0.0dB
Y:-84.3dBV/Pa
Y:-82.1dBm/Pa
D:0.0dB
Z:-25.0dB
Microphone Frequency Response dB Ref.1V/Pa
FEATURES
-50
-60
-70
-80
-90
-100
20 50 100 200 500 1K 2K 5K 10K 20K
0 Deg
0Deg
180 Deg
180Deg
1. Open batterycover then insertbattery (pay attention to the positiveand negative
pole). Close batterycover(please see followingillustration for battery installation).
2. Turnon power switch(5), LCD willshow group andchannel set atlast using time.
3. Group adjust:Press GP button(3) for about3 seconds, GPnumber on LCDwill
flash; release GPbutton (3), nowGP button changesto UP function and CHbutton
(4) changes toDOWN function, press GP button to move GP UPor CH button
to move GPdown.
