ProLights Jet PAR7ZIP Manuel utilisateur

USER MANUAL

English version

Jet PAR7ZIP

7x20W IP65 RGB+WW zoom LED PAR

REV.01-04/23 - PRELIMINARY

Thank you for choosing PROLIGHTS

Please note that every PROLIGHTS product has been designed in Italy to meet quality and performance requirements

for professionals and designed and manufactured for the use and application as shown in this document.

Any other use, if not expressly indicated, could compromise the good condition/operation of the product and/or be

a source of danger.

This product is meant for professional use. Therefore, commercial use of this equipment is subject to the respectively

applicable national accident prevention rules and regulations.

Features, specications and appearance are subject to change without notice. Music & Lights S.r.l. and all afliated

companies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic loss or any other

loss occasioned by the use of, inability to use or reliance on the information contained in this document.

Product user manual can be downloaded from the website www.prolights.it , or can be inquired to the ofcial

PROLIGHTS distributors of your territory (https://www.prolights.it/sales_network.html).

Scanning the below QR Code, you will access the download area of the product page, where you can nd a broad

set of always updated technical documentation: specications, user manual, technical drawings, photometrics,

personalities, xture rmware updates.

The PROLIGHTS Logo, PROLIGHTS names and all other trademark in this document pertaining to PROLIGHTS services

or PROLIGHTS product are trademarks OWNED or licensed by Music & Lights S.r.l., its afliates, and subsidiaries.

04026 - Minturno (LT) ITALY.

Visit the download area

of the product page

PROLIGHTS - Jet PAR7ZIP 01

INDEX

SAFETY INFORMATION 02

1 - PACKAGING 05

PACKAGE CONTENT..................................................................................................... 05

OPTIONAL ACCESSORIES............................................................................................. 05

2 - TECHNICAL DRAWING 05

3 - INSTALLATION 06

MOUNTING.................................................................................................................... 06

4 - CONNECTION TO THE MAINS SUPPLY 07

5 - START UP 07

CONNECT AND DISCONNECT POWER FROM THE PRODUCT.................................. 07

6 - PRODUCT OVERVIEW 08

7 - DMX CONNECTION 09

CONNECTION OF THE CONTROL SIGNAL: DMX LINE .............................................. 09

INSTRUCTIONS FOR A RELIABLE DMX CONNECTION ............................................... 09

CONNECTION DAISY CHAIN........................................................................................ 09

CONNECTION OF THE DMX LINE................................................................................ 09

CONSTRUCTION OF THE DMX TERMINATION ........................................................... 10

DMX ADDRESSING ........................................................................................................ 10

OPERATION AS A WIRELESS TRANSMITTER................................................................ 10

IN TO CRMX................................................................................................................... 11

OPERATION AS A WIRELESS RECEIVER........................................................................ 11

CRMX TO DMX (RX) ....................................................................................................... 11

8 - CONTROL PANEL 12

DISPLAY AND BUTTONS LAYOUT................................................................................. 12

9 - MENU STRUCTURE 13

10 - SHORTCUT 16

11 - RDM FUNCTIONS 17

12 - DMX CHARTS 20

RDM Model ID................................................................................................................ 20

14 - ERROR MESSAGES 28

15 - ACCESSORIES INSTALLATION 29

FILTER FRAME (CODE AJP7ZIPBD - OPTIONAL) .......................................................... 29

BARN DOOR (CODE AJP7ZIPBD - OPTIONAL)............................................................. 30

16 - PERIODICAL CLEANING 31

17 - TEST OF IP65 RATING 32

18 - MAINTENANCE 33

MAINTENANCE AND CLEANING THE PRODUCT........................................................ 33

REPLACING THE FUSE................................................................................................... 33

VISUAL CHECK OF PRODUCT HOUSING ..................................................................... 33

TROUBLESHOOTING..................................................................................................... 34

PROLIGHTS - Jet PAR7ZIP02

SAFETY INFORMATION

WARNING!

• See https://www.prolights.it/product/JETPAR7ZIP#download for installation instruc-

tions.

• Please read carefully the instruction reported in this section before installing, power-

ing, operating or servicing the product and observe the indications also for its future

handling.

This unit is not for household and residential use, only professional applications.

Connection to mains supply

• The Connection to the mains supply must be carried out by a qualied electrical

installer.

• Use only AC supplies 100-240V 50-60 Hz, the xture must be electrically connected

to ground (earth).

• Select the cable cross section in according with the maximum current draw of the

product and the possible number of products connected at the same power line.

• The AC mains power distribution circuit must be equipped with magnetic+residual

current circuit breaker protection.

• Do not connect it to a dimmer system; doing so may damage the product.

Protection and Warning against electrical shock

• Do not remove any cover from the product, always disconnect the product from AC

power before servicing.

• Ensure that the xture is electrically connected to ground (earth). And use only a

source of AC power that complies with local building and electrical codes and has

both overload and ground-fault (earth-fault) protection.

• Before using the xture, check that all power distribution equipment and cables are

in perfect condition and rated for the current requirements of all connected devices.

• Isolate the xture from power immediately if the power plug or any seal, cover, ca-

ble, or other components are damaged, defective, deformed or showing signs of

overheating.

• Do not reapply power until repairs have been completed.

• Refer any service operation not described in this manual to PROLIGHTS Service team

or an authorized PROLIGHTS service center.

Installation

• Make sure that all visible parts of the product are in good visible condition before its

use or installation.

• Make sure the point of anchorage is stable before positioning the projector.

• When suspending the xture above ground level, secure it against failure of primary

attachments by attaching a safety cable that is approved as a safety attachment for

the weight of the xture to the attachment point on the main frame of the product. ln

case the safety cable, enter in action, it needs to be replaced with a new one.

• Install the product only in well ventilated places.

• For non temporary installations, ensure that the xture is securely fastened to a load-

bearing surface with suitable corrosionresistant hardware.

• For a temporary installation with clamps, ensure that the quarter-turn fastener and/or

screws are turned fully, and secured with a suitable safety cable.

PROLIGHTS - Jet PAR7ZIP 03

0,3 m Minimum distance of illuminated objects

• The projector needs to be positioned so that the objects hit by the beam of light are

at least 0,3 meters (0,98 ft) from the lens of the projector.

T 45°C

Max operating ambient temperature (Ta)

• Do not operate the xture if the ambient temperature (Ta) exceeds 45 °C (113 °F).

T -15°C

Minimum operating ambient temperature (Ta)

• Do not operate the xture if the ambient temperature (Ta) is below -15 °C (5 °F).

Protection from burns and re

• The exterior of the xture becomes hot during use. Avoid contact by persons and

materials.

• Ensure that there is free and unobstructed airow around the xture.

• Keep ammable materials well away from the xture.

• Do not expose the front glass to sunlight or any other strong light source from any an-

gle. Lenses can focus the sun’s rays inside the xture, creating a potential re hazard.

• Do not attempt to bypass thermostatic switches or fuses.

IP65

Outdoor (temporary) use

• This product is rated with an IP (Ingress protection) for temporary outdoor use when

used and serviced according to the instruction contained in this document.

• Never use the xture in places subject to vibrations or bumps.

• Make certain that no inammable liquids, water or metal objects enter the xture.

• Excessive dust, smoke uid, and particle build up degrades performance, causes

overheating and will damage the xture.

• Damages caused by inadequate cleaning or maintenance are not covered by the

product warranty.

Light collimation optical system

• This product contains internal light collimation opticsl system. Avoid to expose the

optical system to any intense source of light (including sunlight) from any angle.

T 62°C

Temperature of the external surface

• The surface of the xture can reach up to 62 °C (143,6 °F) during operation. Avoid

contact with people and materials.

Radio receiver

This product contains a radio receiver and/or transmitter:

• Maximum output power: 17 dBm.

• Frequency band: 2.4 GHz.

Maintenance

• Warning! Disconnect the xture from AC mains power and allow to cool for at least

10 minutes before handling.

• Only technicians who are authorized by PROLIGHTS or Authorised service partners

are permitted to open the xture.

• Users may carry out external cleaning, following the warnings and instructions pro-

vided, but any service operation not described in this manual must be referred to a

qualied service technician.

• Important! Excessive dust, smoke uid, and particle build up degrades performance,

causes overheating and will damage the xture. Damages caused by inadequate

cleaning or maintenance is not covered by the product warranty.

PROLIGHTS - Jet PAR7ZIP04

Photobiological safety

• This device emits potentially dangerous optical radiation and is identied in the cat-

egory of Risk Group 2 according to EN 62471.

Do not stare at the operating light source

• Do not look directly at the LED source during operation. It can be harmful to the eyes

and skin.

• During Installation, operation and maintenance, be prepared for the xture to light

and move suddenly when connected to power.

• The device should be positioned so that prolonged staring into the luminaire at adis-

tance closer than TBC m (TBC ft) is not expected.

TBC

Minimun

distance

Risk

Group 2

Risk

Group 1

0.2 m

0.7 ft

10.5 m

34.45 ft

Disposal

• This product is supplied in compliance with European Directive 2012/19/EU – Waste

Electrical and Electronic Equipment (WEEE). To preserve the environment please dis-

pose/ recycle this product at the end of its life according to the local regulation.

The product contains a lithium ion battery

• Don't throw the unit into the garbage at the end of its lifetime.

• Make sure to dispose according to your local ordinances and/or regulations, to avoid

polluting the environment!

• The packaging is recyclable and can be disposed.

The products to which this manual refers comply with:

• 2014/35/EU - Safety of electrical equipment supplied at low voltage (LVD).

• 2014/30/EU - Electromagnetic Compatibility (EMC).

• 2011/65/EU - Restriction of the use of certain hazardous substances (RoHS).

• 2014/53/EU - Radio Equipment Directive (RED).

Other approvals

PROLIGHTS - Jet PAR7ZIP 05

1 - PACKAGING

PACKAGE CONTENT

• 1x JETPAR7ZIP.

• 1x 1,5 meters power cable (BARE END - SEETRONIC POWERCON TRUE1 IP65).

• User Manual.

OPTIONAL ACCESSORIES

• AJP7ZIPBD: barn door with 8 directional aps to adjust the light beam, ASTRA / JET PAR7ZIP.

• IPTESTBOX: portable vacuum and pressure tester for ProLights IP xtures.

• C6002A/B: slim aluminium clamp, 200 kg loading, 48-51 mm tubes, M10 bolt, aluminium / black.

• RSR0670A/B: steel security cable for hanging bodies, inox steel shackle, aluminium / black.

• WSBBF1G5: blackBox F-1 G5 transmitter, 2,45GHz & 5.2/5,8 GHz, DMX/RDM, 512Ch.

• WSBBF1G6: blackBox F-1 G6 transrec, 512ch, 2.45GHz, DMX&RDM,Bluetooth,G3,G4,G4S, G5, CRMX.

• WSBBR512G5: blackBox R-512 G5 receiver 512Ch, 2.45GHz & 5.8GHz, DMX/RDM optional.

• WSBBR512G6: blackBox R-512 G6 receiver 512Ch, 2.45GHz,DMX&RDM,Bluetooth,G3,G4,G4S,G5,CRMX.

• UPBOX2P5: rmware uploader kit, USB IN, 5-pin XLR DMX OUT.

292 mm

[11.5 in]

302 mm

[11.9 in]

Ø451 mm

[17.8 in]

Ø481 mm

[18.9 in]

345 mm

[13.6 in]

Fig. 01

Weight: 9,3 kg - 20,50 lbs

2 - TECHNICAL DRAWING

PROLIGHTS - Jet PAR7ZIP06

Fig.02

3 - INSTALLATION

MOUNTING

Check that the supporting structure can safely bear the weight of all installed xtures, clamps, cables,

auxiliary equipment, etc. and complies with locally applicable regulations.

When suspending the xture above ground level, secure it against failure of primary attachments by

attaching a safety wire that is approved as a safety attachment for the weight of the xture to an anchor

point on the product main frame.

Do not use removable parts or weak anchors for secondary attachment.

Warning! When clamping the xture to a truss or other structure at any angle, use clamps of half-cou-

pler type. Do not use any type of clamp that does not completely encircle the structure when fastened.

RSR0670A/B

Steel security cable C6002 A/B clamp

98,50 mm

3,88 in

Ø13 mm

0,51 in

PROLIGHTS - Jet PAR7ZIP 07

5 - START UP

CONNECT AND DISCONNECT POWER FROM THE PRODUCT

To apply and disconnect power to the product:

• Check that the product is installed and secured as indicated in the Safety Informations, and that

personal safety will not be put at risk when the xture lights up.

• Connect the power connector into the Mains input socket (100-240 VAC-50/60 Hz).

• The product is then ready for its operations and can be controlled through the available input sig-

nals on board.

• To disconnect power from the product, disconnect the Mains from the socket.

4 - CONNECTION TO THE MAINS SUPPLY

WARNING: For protection from electric shock, the xture must be earthed!

The product is equipped with auto-switching power supply that automatically adjusts to any 50-60Hz

AC power source from 100-240 Volts.

If you need to install a power plug on the power cable to allow connection to power outlets, install a

grounding-type (earthed) plug, following the plug manufacturer’s instructions. If you have any doubts

about proper installation, consult a qualied electrician.

The max power consumption is 140W.

Core (EU) Core (US) Connection Plug terminal marking

Brown Black Live L

Blue White Neutral N

Yellow+green Green Earth

PROLIGHTS - Jet PAR7ZIP08

MODE/

ESC UP DOWN ENTER

6 - PRODUCT OVERVIEW

1. BRACKET for hanging safe.

2. BRACKET for oor positioning.

3. HOLDER CLIP for lter frame and barndoor accessory.

4. KNOB for bracket.

5. SAFETY EYE to attach safety cable.

6. GORE VALVE.

7. USER INTERFACE with display and buttons for access to the control panel functions.

8. MAIN FUSE HOLDER: replace a burnt-out fuse by one of the same type only (3.15A).

9. ANTENNA.

10.DMX IN (5-p XLR): 1 = GND, 2 = sign-, 3 = sign+, 4 N/C, 5 N/C.

11.DMX OUT (5-p XLR): 1 = GND, 2 = sign-, 3 = sign+, 4 N/C, 5 N/C.

12.POWER OUT: power output for connection of multiple units in series.

13.POWER IN: for connection to the Mains 100-240V~/50-60Hz.

Fig 03

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ProLights Équipement d'éclairage

ProLights

ProLights CROMOSPOT250 Manuel utilisateur

ProLights

ProLights FS75LED Manuel utilisateur

ProLights

ProLights LUMA 1500SH Manuel utilisateur

ProLights

ProLights Astra Wash19PixIP Manuel utilisateur

ProLights

ProLights SmartBat Plus Manuel utilisateur

ProLights

ProLights V575SPOT Manuel utilisateur

ProLights

ProLights LUMIPAR12Q Manuel utilisateur

ProLights

ProLights FURY FY250W Manuel utilisateur

ProLights

ProLights EclPanel TWC Manuel utilisateur

ProLights

ProLights SLASH Manuel utilisateur

ProLights

ProLights EclProfile FW Manuel utilisateur

ProLights

ProLights UV Panel Manuel utilisateur

ProLights

ProLights Cyber24 Manuel utilisateur

ProLights

ProLights Astra Wash19Pix Manuel utilisateur

ProLights

ProLights ECL Series Manuel utilisateur

ProLights

ProLights Sunrise 2IP Manuel utilisateur

ProLights

ProLights NEWMOON Manuel utilisateur

ProLights

ProLights ARCLED2033 Manuel utilisateur

ProLights

ProLights LEDFLOWERKIT4 Manuel utilisateur

ProLights

ProLights ECLIPSEJZIP Manuel utilisateur

ProLights

ProLights EclNanoPanel TWC Manuel utilisateur

ProLights

ProLights LUXOR Manuel utilisateur

ProLights

ProLights Astra Profile600IP Manuel utilisateur

ProLights

ProLights LUMIPAR12IRTRI Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur