PROLED CP-CL04 Manuel utilisateur
Motion Sensor LED Cabinet Light
User Manual
Model: CP-CL04
*PLEASE NOTE: Once the remote has been used, even in auto mode, the
remote overrides the switch function selected on the light itself. To reset, switch the
unit to OFF and then back to ON or AUTO mode* This will need to be repeated
after each remote use if you are wanting to be able to use the AUTO (Motion Senor)
function.
How to use
The Light has 3 working modes. (AUTO – Motion Sensor, OFF & ON-stays on all
the time)
1.
Remove plastic protective film from the top of the light.
2.
Pull out the plastic tab from battery compartment, on the remote control.
3.
Slide the switch on the light to ON, the light will come on and stay on.
4.
Slide switch to OFF, to turn the light off.
5.
Slide switch to AUTO, to operate in the motion sensor mode. Light will work only
in dark or shadowed/shaded areas. The light will turn on automatically when motion
is detected within range. The light will turn off automatically after approximately 90
seconds, or when no motion is detected.
6.
Slide the switch to “OFF” to save battery power if you do not use the light for a long time.
7.
Select Light Color (Warm or Cool), by pressing the round button on the top of light
or on the remote control.
8.
Control the light brightness by using the remote control. Push the 30% button to
reduce the light brightness and to conserve battery life.
9.
Push the + or – to increase or decrease the desired brightness.
10.
Default brightness when turning on the light is at 100 % brightness.
How to use the timer function
Timer function only functions properly when the switch on the bottom of the light
is in the ON position, do not use timer in AUTO mode.
1.
Turn the switch on the bottom of the light to ON position.
2.
Using the remote, push the button with the desired time to shut off (1 minute, 5 minutes, 15
minutes, or 30 minutes)
3.
Light will blink twice letting you know the timer has been set to shut off in desired minutes
selected.
4.
If you push the wrong desired time button, simply push the correct desired time button, and it will
override the previous selection.
5.
To remove the timer function, turn the switch on the bottom of the light to OFF and then back to
ON or AUTO.
How to charge the motion sensor led cabinet light
Please use 5V 1A power adapter and USB cord to charge the light, the indicator
turns red when the light is charging, it turns green when the light is fully charged.
How to install the under-cabinet light
1.
Stick it directly to any metal surface.
2.
Use metal bracket with tape, to stick anywhere you want.
Specification
Product Dimension
11.8 x 1.6 x 0.90 inches
Input Voltage
120V 60Hz
Battery
3.7V 1000mAh
Charge Time
approx. 3-4 hrs.
Control Distance
approx. 9 – 16 Feet
Runtime
approx. 3-4 hrs. (100% brightness always on mode)
Lumen Output
160 lm±10%
Standby Time
Approx. 90 seconds
Sensor Range
approx. 9- 16 Feet
Warning: Protect from heat, do not store over 122 degrees F.
This device complies with part 15 of the FCC Rules. Operation is subject to the following.
two conditions: (1) This device may not cause harmful interference, and (2) this device.
must accept any interference received, including interference that may cause undesired.
operation.
Table des matières
Autres manuels PROLED Équipement d'éclairage
PROLED
PROLED FLEX STRIP Manuel utilisateur
PROLED
PROLED L6OP6 Series Manuel utilisateur
PROLED
PROLED PAD300 Manuel utilisateur
PROLED
PROLED L65XT000 Manuel utilisateur
PROLED
PROLED FLEX STRIP EXTENDED 700 Manuel utilisateur
PROLED
PROLED L6OP7 Series Manuel utilisateur
PROLED
PROLED 389 Series Manuel utilisateur
PROLED
PROLED L500015 Series Manuel utilisateur
Manuels Équipement d'éclairage populaires d'autres marques
Qazqa
Qazqa Suplux SL 3 Black 103062 Manuel utilisateur
Commercial Electric
Commercial Electric 54568141 Manuel utilisateur
CREE LIGHTING
CREE LIGHTING 304 Series Manuel utilisateur
Goobay
Goobay 49867 Manuel utilisateur
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manuel utilisateur
Alkalite
Alkalite Krypton KT-81 Manuel utilisateur
