Projecta AC150 Manuel utilisateur

AUTOMATIC

BATTERY CHARGER

CHARGE N’ MAINTAIN

P/No’S. AC150, AC250B, AC400, AC600, AC800, AC1000, AC1500, AC600-24

WARNING

• Explosive gases. Prevent flames and sparks. Provide adequate ventilation during

charging.

• Before charging, read the instructions.

• For indoor use. Do not expose to rain.

• For charging lead acid batteries ONLY (of the size & voltage specified in the

specifications table).

• Disconnect the 240V mains supply before making or breaking the connections

to the battery.

• Do not attempt to charge non-rechargeable batteries.

• Never charge a frozen battery.

• This appliance is not intended for use by young children or infirm persons unless they

have been adequately supervised by a responsible person to ensure that they can use

the appliance safely.

• Young children should be supervised to ensure that they do not play with the

appliance.

•

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or

similarly qualified persons in order to avoid a hazard.

• After charging, disconnect the battery charger from the supply mains. Then remove the

chassis connection and then the battery connection.

FEATURES

Automatic Charger

An automatic battery charger stops charging when the battery is full. You can leave the charger

connected to the battery without risk of overcharging. Once the battery is full, the battery

charger will automatically start to maintain the battery. The charger monitors the battery

Voltage

and continues to top up the battery, keeping it fully charged and ready for use.

Thermal Overload/Polarity Protection

Prevents the output leads from sparking due to accidental reverse connection or short circuit

making the charger safer to use around batteries.

LED Charge Indication

Three LEDs display the charger’s status (except AC250B).

• RED LIGHT ON: Power On,

• ORANGE LIGHT ON: Charging,

• GREEN LIGHT ON: Fully charged and maintaining.

Wiring harness (AC150 & AC250B only)

The wiring harness allows for easy connection to vehicles that have hard to reach batteries.

Includes an inline fuse (AC150) to protect the harness from accidental short circuits.

‘On Board’ Battery Charging (AC250B only)

The AC250B ‘On Board’ charger allows the charger to be conveniently mounted on the vehicle

next to the battery. This is an ideal solution for vehicles left unused for some time. When the

vehicle is to be garaged, simply pop the hood and plug the charger in to a 240 Volt extension

cord. When the vehicle is to be used, disconnect the extension cord, close the hood and start

the engine, it’s that easy!

Multi Voltage (AC400 only)

Can charge either 6V or 12V batteries.

Engine Start (AC800 only)

When time is short, this feature will deliver the battery a short yet powerful enough charge

to start the engine.

Toroidal Transformer (AC1000, AC1500 & AC600-24 only)

Using the latest technology in transformer design, toroidal transformers don’t use a solid iron

core (like traditional transformers) making them lighter and more compact. They deliver more

power than a traditional transformer charger of the same size.

SPECIFICATIONS

P/No. AC150 AC250B AC400 AC600 AC800 AC1000 AC1500 AC600-24

Type: AUTOMATIC AUTOMATIC AUTOMATIC AUTOMATIC AUTOMATIC AUTOMATIC AUTOMATIC AUTOMATIC

Input: 240VAC 50Hz 240VAC 50Hz 240VAC 50Hz 240VAC 50Hz 240VAC 50Hz 240VAC 50Hz 240VAC 50Hz 240VAC 50Hz

Input power: 0.09A (17W) 0.2A (28W) 0.23A (53W) 0.37A (70W) 0.43A (91W) 0.5A (108W) 0.83A (161W) 0.6A (116W)

Output Voltage: (Nominal) 12VDC 12VDC 6 VDC/12VDC 12VDC 12VDC 12VDC 12VDC 24VDC

Output Current: 900mA@12V 1600mA@12V 2700mA 4300mA@12V 5400mA@12V 6200mA@12V 10000mA@12V 3500mA@24V

(Continuous) @6 or 12V

Engine Start: N/A N/A N/A N/A 3 Cycles: N/A N/A N/A

5min ‘ON’

20min ‘OFF’

Suitable for Charging 12V Battery 12V Battery 6 or 12V Battery 12V Battery 12V Battery 12V Battery 12V Battery 2 x 12V

in series (24V)

Battery Range: (CCA) 100-350* 200-650* 250-550 250-650 300-700 300-800 450-1000 400-900*

(MCA) 150-400* 250-700* 250-600 300-700 375-800 375-900 600-1200 450-1000*

(Ah) 7-24 16-40 20-70 25-80 35-100 50-100 65-150 35-70

Minimum Start Voltage: 5V 5V 3V 3V 3V 3V 3V 15V

Charge Control: (Cut out) 14.2V 14.2V 7.1/14.2V 14.2V 14.2V 14.2V 14.2V 28.4V

(Cut in) 13.4V 13.4V 6.7/13.4V 13.4V 13.4V 13.4V 13.4V 26.8V

Size: 65x85x95mm 123x43x120mm 150x140x85mm 150x140x85mm 190x220x120mm 190x220x120mm 190x220x120mm 190x220x120mm

Weight: 0.75Kg 1.3Kg 1.5Kg 1.9Kg 2.5Kg 2.6Kg 3.4Kg 2.6Kg

*Only suitable for maintaining larger size batteries.

CHARGING INSTRUCTIONS

STEP 1 - CHECK THE ELECTROLYTE LEVEL

Prior to charging the battery, remove the vent caps and check the electrolyte level.

(Not required on sealed & maintenance free batteries).

The electrolyte should be 6mm (1/4”) above the battery’s plates.

If low, top up the electrolyte with distilled water to the correct level and refit the vent caps.

STEP 2A - CONNECTION OUT OF VEHICLE

Connect the RED lead (battery clip) from the charger to the Positive (+) battery post.

Connect the BLACK lead (battery clip) from the charger to the Negative (-) battery post.

STEP 2B - CONNECTION IN VEHICLE

Determine if the vehicle is Positively (+) or Negatively (-) earthed. Negatively earthed vehicles

have a cable (usually black) from the Negative battery terminal to the vehicle’s chassis.

Negatively earthed (Most Vehicles)

Connect the RED lead (battery clip) from the charger to the Positive (+) battery terminal.

Connect the BLACK lead (battery clip) from the charger to the vehicle’s chassis away from the

fuel line or moving parts.

CONNECTION OUT OF VEHICLE

CONNECTION IN VEHICLE (NEGATIVELY EARTHED)

Positively earthed

Connect the BLACK lead (battery clip) from the charger to the Negative (-) battery terminal.

Connect the RED lead (battery clip) from the charger to the vehicle’s chassis away from the

fuel line or moving parts.

STEP 2C - CONNECTION IN VEHICLE WITH HARNESS (AC150 & AC250B ONLY)

Connect the RED ring terminal of the harness to the Positive (+) battery terminal.

Connect the BLACK ring terminal of the harness to the Negative (-) battery terminal.

Connect the plug on the harness to the charger’s output lead socket.

STEP 3 - BATTERY CHARGER SETTINGS (AC400 & AC800 ONLY)

Set the voltage selection switch to either 6V or 12V (AC400)

Set the ‘Charge/Engine Start’ switch to the ‘Charging’ position (AC800).

CONNECTION IN VEHICLE (POSITIVELY EARTHED)

POWERON

FULLY

CHARGED

CHARGING

CONNECTION IN VEHICLE USING HARNESS

Vehicle Harnes

SWITCH SELECTION

AC400

Push in 12V side

for 12V Battery

Push in Charging

side for charging

AC800

STEP 4 - CONNECT TO 240V MAINS POWER.

Connect the battery charger to a 240V mains powered socket.

Turn on the 240V Mains Power.

The RED ‘POWER ON’ LED will illuminate to confirm that the charger is receiving power

(except AC250B).

STEP 5 - CHARGING

The orange ‘Charging’ LED (or red LED on AC250B) will illuminate to confirm that the

battery is charging.

When the battery is fully charged the Orange ‘Charging’ LED (or red LED on AC250B) will

extinguish and the Green ‘Fully Charged’ LED will illuminate. The battery is now fully charged

and ready for use.

If left connected, the charger will monitor the battery and maintain the battery ready for use

until required. This prevents the battery from slow self-discharge, which is detrimental to

lead acid batteries.

STEP 6 - DISCONNECTION.

Turn the 240V mains power off.

Battery out of vehicle

Remove the BLACK lead (battery clip) from the battery.

Remove the RED lead (battery clip) from the battery.

Battery in vehicle

Remove the chassis connection.

Remove the battery terminal connection.

Battery in vehicle using harness (AC150 & AC250B only)

Unplug the harness from the charger’s output lead.

ENGINE START (AC800 ONLY)

The Engine start function on the AC800 is designed to provide a short term ‘Boost” to the

battery and then assist the battery to start the vehicle.

1. Connect the charger to the battery as described above in step 2b ‘In Vehicle Connection’.

2. Connect the battery charger to the 240V mains power.

3. Set the ‘Charge/Engine Start’ switch to the ‘Engine Start’ position.

4. Connect the charger to the battery as described above in step 2b ‘In Vehicle Connection’.

Connect the battery charger to the 240V mains power. Turn on the 240V Mains Power.

The RED ‘POWER ON’ LED will illuminate to confirm that the charger is receiving power.

If the battery is connected properly and above the charger’s minimum voltage the Orange

‘Charging’ LED will illuminate to confirm that the battery is being charged.

5. After 5 minutes or if the Green ‘Fully Charged’ LED illuminates, attempt to crank the engine

(with the charger connected / turned on).

6. If the engine starts:

• Turn ‘OFF’ the 240V mains power and disconnect the charger from the mains power.

• Remove the chassis connection.

• Remove the battery terminal connection.

7. If the engine does not start:

• Turn ‘OFF’ the 240V mains power.

• Wait 20 minutes and then repeat steps 4–6.

• If after 3 cycles the engine does not start, the battery is probably too flat or defective.

Recharge the battery completely.

‘ON BOARD’ BATTERY CHARGING (AC250B ONLY)

The AC250B ‘On Board’ charger allows the charger to be conveniently mounted on the vehicle.

The charger can be mounted to any flat surface using the mounting tabs or bolted to the

supplied ‘L’ Bracket (Bolts, Washers & Nuts Supplied) and mounted next to the battery

as per the diagram.

Push in

Engine Start side

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Projecta Chargeur de batteries

Projecta

Projecta INTELLI-RV PM200 Manuel utilisateur

Projecta

Projecta HDBC45 Manuel utilisateur

Projecta

Projecta IM120 Manuel utilisateur

Projecta

Projecta IC2500L Manuel utilisateur

Projecta

Projecta INTELLI JAY PM100-BTJ Manuel utilisateur

Projecta

Projecta DC20 Manuel utilisateur

Projecta

Projecta HDBC90 Manuel utilisateur

Projecta

Projecta IC2500 Manuel utilisateur

Projecta

Projecta HDBC20 Manuel utilisateur

Projecta

Projecta INTELLI-RV PM300 Manuel utilisateur

Projecta

Projecta IC700 Manuel utilisateur

Projecta

Projecta IDC25 Manuel utilisateur

Projecta

Projecta INTELLI-CHARGE IC25 Manuel utilisateur

Projecta

Projecta INTELLI-CHARGE IC7 Manuel utilisateur

Projecta

Projecta HDBM4000 Manuel utilisateur

Projecta

Projecta IDC25X Manuel utilisateur

Projecta

Projecta INVCHRD-BT Manuel utilisateur

Projecta

Projecta INTELLI-CHARGE DC/SOLAR BATTERY CHARGER... Manuel utilisateur

Projecta

Projecta PMDCS30 Manuel utilisateur

Projecta

Projecta INVCHR2 Manuel utilisateur

Projecta

Projecta IC1500L Manuel utilisateur

Projecta

Projecta WORKSHOP HDBC21 Manuel utilisateur

Projecta

Projecta IC100L Manuel utilisateur

Projecta

Projecta Charge N' Maintain Manuel utilisateur

Manuels Chargeur de batteries populaires d'autres marques

AA Portable Power Corp

AA Portable Power Corp Universal Smart Charger Manuel utilisateur

Enelion

Enelion Vertica Manuel utilisateur

RCA

RCA CHU6 Manuel utilisateur

ANSMANN

ANSMANN ALCT 6/24-10 Manuel utilisateur

Hitachi

Hitachi UC 18YRSL Guide de dépannage

Olympus

Olympus B-20 LPC Manuel utilisateur

Exibel

Exibel ZH1708143 Manuel utilisateur

Lenmar

Lenmar Mach 1 Manuel utilisateur

CTEK

CTEK MXS 5.0 Manuel utilisateur

ABB

ABB HT842379 Manuel utilisateur

Nitecore

Nitecore Superb Charger SC4 Manuel utilisateur

Renogy

Renogy RBC2125DS-21W Manuel utilisateur

Braun

Braun BWC02M Manuel utilisateur

CTEK

CTEK MXS 3.6 Manuel utilisateur

Black & Decker

Black & Decker BDV090 Manuel utilisateur

Trinity

Trinity DPD Manuel utilisateur

Hulkman

Hulkman Sigma 1 Manuel utilisateur

IKEA

IKEA koppla Manuel utilisateur