ProfiTap X2 Series Manuel utilisateur

X2-2000G

PSU1 PSU2 FAN STAT

QUICK START GUIDE

X2-2000G

1CAREFULLY UNPACK ALL THE ITEMS AND RETAIN THE PACKAGING FOR LATER USE

X2-2000G is shipped with the following items:

X2-2000G is designed to be rack

mounted. Make sure the unit is

properly grounded and secured in

the rack using the included screws

and pre-mounted brackets.

Front Panel

Rear Panel

2CONNECTING POWER & START UP

Power on the device by connecting the included AC power cord(s) to device and main power.

The unit starts up and boots once it is powered. You can follow its status by observing the activity LEDs.

Stage 2 (~2 secs): SYS, PWR, FAN LEDs green, fans at normal speed

FAN, SYS: Green if normal fan/system operation, red if fan/system fault

PWR: Green if present and operational, red if PSU fault

Stage 1 (~35 secs): SYS LED blink green, PWR LED green, FAN LED o, fans at full speed

BOOT SEQUENCE ~ SECS

NORMAL OPERATION MODE

SYS PWR FAN LOC

[2]

[1]

X2-2000G features a serial management port, located on its rear panel [2]. Connecting through this port allows the users to make the

initial setup on the device, configuring its network interface.

NOTE: If you are planning on using the device on a dynamic IP network, you can skip this step. The device will get an IP address

automatically and will be accessible via GUI or CLI with the default credentials:

User: admin

Password: Adminadmin1

INITIAL SETUP OVER SERIAL CONNECTION

PSU1

PPS IN-OUT

RESET

CTRL 1

CTRL 2

MGMT

CONSOLE

LINK ACT

PPS IN-OUT

RESET

CTRL 1

CTRL 2

MGMT

CONSOLE

LINK ACT

X2-2000G main unit

2 x C13 AC power cord

1 x RJ45 female to 9-pin serial adapter

1 x USB/RJ45 adapter cable

1 x RJ45 cable

1 x rack mounting kit (front and

rear brackets, screws)

Connect the X2-2000G's Ethernet management port [1] to a network or computer, using an RJ45 Ethernet

cable. Keep in mind, in case you connect the unit directly to a computer, manual IP policy must be applied for

both the unit and the computer. Additionally, if the computer network interface is only 10/100M capable, a

twisted pair Ethernet cable must be used instead of a normal patch cable.

To access the X2-Manager interface, type

h t t p s://< i p_addr>

in your browser (Firefox or Chrome

recommended) with <ip_addr> being the unit’s static or DHCP provided IP.

On success, override any browser certificate alert to continue. X2-2000G prompts with its Status Page.

The main X2-Manager screen is displayed. For more information on X2-Manager, please refer to the User

Manual.

MANAGING X2-2000G USING X2-MANAGER

After the initial setup has been completed, or if the device is using a dynamic IP, the X2-Manager web interface can be accessed via the

device's Ethernet management port [1], either locally or over the network.

Provided the device is connected to a network or directly to a computer (see: step 4A), connect to X2-2000G

through SSH (default port 22), using its static or DHCP provided IP.

For more information on available CLI commands, please refer to the User Manual.

After the initial setup has been completed, or if the device is using a dynamic IP, the management CLI can be accessed via the device's

Ethernet management port [1], either locally or over the network.

MANAGING X2-2000G THROUGH CLI OVER SSH

Download the latest user manual from https://resources.profitap.com/

Profitap HQ B.V. — High Tech Campus 84 — 5656AG Eindhoven — The Netherlands

info@profitap.com — +31 (0) 40 782 0880 — www.profitap.com

v1.2 — 03/22

Connect the X2-2000G serial administration port to a computer, using the supplied cable and adapters.

Use the following settings when connecting to the device: 115200 baud rate, 8 bit, no parity, 1 bit stop.

Default username: admin

Default password: Adminadmin1

Change network configuration using the .system.network.set command.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ProfiTap Matériel réseau

ProfiTap

ProfiTap C1R-1G Manuel utilisateur

ProfiTap

ProfiTap C1-100 Manuel utilisateur

ProfiTap

ProfiTap C1D-1G Manuel utilisateur

ProfiTap

ProfiTap 10GBASE-T Manuel utilisateur

ProfiTap

ProfiTap IOTA 1G Manuel utilisateur

ProfiTap

ProfiTap C1-1G-RG2 Manuel utilisateur

ProfiTap

ProfiTap PROFISHARK 1G Manuel utilisateur

ProfiTap

ProfiTap F1-10G-BP BYPASS TAP Manuel

ProfiTap

ProfiTap C8-1G Manuel utilisateur

ProfiTap

ProfiTap F4-10G-BP BYPASS TAP Manuel

ProfiTap

ProfiTap X2-3200G Manuel utilisateur

ProfiTap

ProfiTap IOTA 1G Manuel utilisateur

ProfiTap

ProfiTap F1-40G-BP BYPASS TAP Manuel

ProfiTap

ProfiTap PROFISHARK 1G+ Manuel

ProfiTap

ProfiTap XX Series Manuel utilisateur

ProfiTap

ProfiTap PROFISHARK 100M Manuel utilisateur

ProfiTap

ProfiTap X2-3200G Manuel utilisateur

ProfiTap

ProfiTap XX Series Manuel utilisateur

ProfiTap

ProfiTap ProfiShark 10G Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur