Profile MP6600 Manuel de service
AM/FM HIGH POWER SLIDE DOWN DETACHABLE FACE
MP3 / COMPACT DISC PLAYER
Installation Instructions / Owner's Manual
MP6600
CD-R/RW
60W x 4
1
INTRODUCTION
Congratulations on your purchase of a Profile state-of-the-art single disc CD/MP3 player.
Your selection of a Profile car audio product indicates a true appreciation of fine musical
reproduction. Whether adding to an existing system or including your Profile CD/MP3 player
inanewsystem,youarecertaintonoticeimmediateperformancebenefits.
FEATURES
60W x 4 Power Output Power Level Meter
MP3 Playback Multi-Color LCD
CD-R/CD-RW Capability Infrared Remote Control
Dual RCA Line Output ISO/DIN Mounting
Clock Blinking Security L.E.D.
24 Station Memory Full Electronic Function Controls
4 Band Preset Equalizer Disc Scan, Random & Repeat Play
KEEP YOUR SALES RECEIPT
Takethistimetoattachyoursalesreceipttothemanualandputinasafeplace. Incaseofany
reason this product may need warranty service, your receipt will be necessary to establish
purchasedate.
IMPORTANT! Before making any connections, disconnect the car’s battery
until the installation is completed to avoid possible damage to the electrical
system.
Serial # Purchase Date
2MP6600
SAFETY PRECAUTIONS
Secure the CD/MP3 player.
When installing your CD/MP3 player in the vehicle, make sure it is mounted properly in the
dash, using an after market installation kit if needed. When using the supplied mounting
bracket, it is a must that you also use the supplied back brace to support the back of the
CD/MP3 player.
Use caution when mounting the CD/MP3 player.
Remember there are many electrical wires, vacuum lines, brake lines and air bag deployment
wires. Make sure you know where they are when mounting the CD/MP3 player to avoid
puncturinglines,andshortingwires.
Use high grade wire connectors.
To ensure maximum power transfer and secure safe connections, it is recommended to use
highgradebarrelorcrimpcapconnectors.
Do not run any wires underneath the vehicle.
Exposedwires can be cut ordamaged. It is best to runall wires through the vehicleunder the
carpetand/orsidepanels. Thisenablestoacleanerinstallationandlessriskofdamage.
Run signal wires away from electrical wires.
To avoid possibility of induced noise from the car's electrical system (i.e. popping noises or
enginenoise),runsignalwiresawayfromthecar'selectricalwiring.
Make all ground wires as short as possible and terminated at the same point.
In order to reduce the chance of ground loops (i.e. engine noise), make the grounded wire as
shortas possible to reducethewire'sresistance. Also, when using multiple components,make
sureallunitsaregroundedatthesamepoint.
Avoid sharp edges when running the wires.
Toavoidthepossibilityofpower,signalorspeakershorts,becarefulnot toallowtheamplifier
wires to come in contact with sharp edges. Use a grommet to protect the wire when running
throughthefirewall.
3
CARE AND MAINTENANCE
Cleaning the CD/MP3 player.
Whencleaning the vehicle, be sure not to getanywaterinoron the CD/MP3 player. Clean only
theexteriorsurfaceoftheunitwithadry,cleansofttowelusingnochemicalsolvents.
Operating in extreme temperatures
Sometimes the unit will not operate in extreme, hot or cold temperatures. If this is the case,
waituntilthetemperatureinthevehicleisnormal,thenresumeoperation.
Protect your CD’s.
When not using the disc player, it is recommended that you remove the CD. Do not leave an
ejected disc sitting on the edge of the disc player for long periods of time. The disc will warp
under direct sunlight. Always put each disc in its case to protect them during times of non-
use.
CD operation.
Neverattempttoforceanythingotherthanacompactdiscinthe disc slot. This disc player is
aprecisioninstrumentthatcouldbedamagedbyaforeignobject.
Disc skip.
When driving down a very rough road, the disc may skip. This will not scratch or damage the
disc.
Removing and protecting detachable front panel.
The front panel of the radio may be removed as a theft deterrent. After removing the front
panel,usethecaseprovidedtokeepthefrontpanelfromgettingdamaged.
4
PUSH RELEASE BUTTON
TO DETACH THE FRONT PANEL
MP6600
ELECTRICAL AND SIGNAL CONNECTIONS
Before making the following connections, take time to look over the vehicle’s wiring and
determinethelocation and wires you will be connecting to. If youdonot wish to cut or tap into
the vehicles existing factory wiring, there are wiring kits available at your car audio retailer
that will allow you to plug directly into the factory wiring harness. Make sure to test all wires
beforeconnectingtotheCDPlayer.
!ConnectBlackwiretochassisground.
!ConnecttheVioletmemorybackup wiretoaConstant+12Voltpowersourcewire.
!ConnecttheRedignitionwiretoanaccessory+12Voltpowersourcewire.(Thepower
wirethatisenergizedwhenthekeyisintheaccessoryposition).
!TheWhitewireisconnectedonlyifapowerantennaoranamplifierisusedinthe
system.Thiswiresupplies+12VoltoutputwhentheCDPlayeristurnedon,
whichactivatesmostpowerantennarelaysoramplifierturnoncircuits.
5
RED
RED
VIOLET
VIOLET
CONSTANT
+12V
SWITCHED +12V
(ON WITH IGNITION)
+12V REMOTE OUTPUT
FOR AMPLIFIER TURN-ON
OR POWER ANTENNA
BLACK
BLACK
BATTERY
+12V
FRONT RIGHT
SPEAKER
(4 OHM)
FRONT LEFT
SPEAKER
(4 OHM)
LOW LEVEL SIGNAL OUTPUT
FOR CONNECTION TO
AMPLIFIERS OR SIGNAL
PROCESSORS
ANTENNA
CONNECTOR
REAR LEFT
SPEAKER
(4 OHM)
REAR RIGHT
SPEAKER
(4 OHM)
BROWN
GREY
WHITE
WHITE
BLACK/WHITE
BLUE
YELLOW
ORANGE
GREEN
PINK
FUSES
LEFT CHANNEL (WHITE)
LEFT CHANNEL (WHITE) FRONT
RCA’S
BLACK
WIRES
GREY
WIRES
REAR
RCA’S
RIGHT CHANNEL (RED)
RIGHT CHANNEL (RED)
FOUR SPEAKER SYSTEM
FUSES
15A (VIOLET WIRE)
1A (RED WIRE)
6
TWO SPEAKER SYSTEM
CAUTION! Tape unused wires so they do not short against other wires or
chassis ground.
RED
RED
VIOLET
VIOLET
CONSTANT
+12V
SWITCHED +12V
(ON WITH IGNITION)
+12V REMOTE OUTPUT
FOR AMPLIFIER TURN-ON
OR POWER ANTENNA
BLACK
BLACK
BATTERY
+12V
FRONT RIGHT
SPEAKER
(4 OHM)
FRONT LEFT
SPEAKER
(4 OHM)
LOW LEVEL SIGNAL OUTPUT
FOR CONNECTION TO
AMPLIFIERS OR SIGNAL
PROCESSORS
ANTENNA
CONNECTOR
BROWN
GREY
WHITE
WHITE
BLACK/WHITE
NOT USED
PINK
FUSES
LEFT CHANNEL (WHITE)
LEFT CHANNEL (WHITE)
RIGHT CHANNEL (RED)
RIGHT CHANNEL (RED)
NOT USED
NOT USED
NOT USED
FRONT
RCA’S
BLACK
WIRES
GREY
WIRES
REAR
RCA’S
FUSES
15A (VIOLET WIRE)
1A (RED WIRE)
MP6600
7
MOUNTING THE CD/MP3 PLAYER
There are two different ways to mount the CD / MP3 Player. In most Japanese vehicles you
can use the factory mounting brackets, taking advantage of the ISO/DIN opening. If your
vehicle does not have ISO/DIN opening, you can mount the CD/MP3 Player using the supplied
DINsleeveandrearsupportbracket. Whenconsideringyourmountinglocation,makesurethe
unit will be level. If you cannot mount the CD/MP3 Player level, due to your vehicle’s design,
make sure there is no more than a 30 degree tilt. Keeping this in mind will assure proper
CD/MP3playandoverallreliability.
DIN SLEEVE MOUNTING
Insert the mounting sleeve into a
standard DIN cutout in the dash
kit, dashboard or Console.
Bend the mounting tabs of the sleeve
with a screwdriver to secure the bracket
firmly in place.
Insert the CD/MP3 Player in the
mounting sleeve until it locks.
8
Attach the back brace to the
CD/MP3 player using the supplied
hardware. Then attach the other
end of the brace to a firm
mounting surface (i.e. Dash brace,
fire wall, e.t.c.) This will brace the
back of the CD/MP3 player to
ensure solid mounting to prevent
theft and provide optimal CD play.
Once the CD/MP3 player is secured, fit the trim ring over outside edge of the radio until it
snapsinto place. Inserttheface plate withtheright side first.Anglein therightsideslightly
thengentlypushtheleftsideoffaceplateuntilitsnapscompletelyinplace.
MP6600
9
ISO/DIN MOUNTING
Ifyou own aJapanesevehicle,you can use themountingscrew holes on thesideofthe CD/MP3
playertoattachtothefactorymountingbrackets.
!DetachtheremovablefaceoftheMP6600bydepressingthereleasebutton
!Removetheoutsidetrimringbygentlypullingatbothouteredges(See page10).
!Removethesideretainingplatesbyunscrewingthetwophillipsscrews.
!Removethebracketsfromthefactoryradio,payingcloseattentiontotheirposition.
!AttachthebracketstotheMP6600inthesamepositionasthefactoryradio.
!Afterattachingthewiringharnesstothefactorywiringloom(SeeElectricaland
SignalConnections)andpluggingtheantennalead,placetheCD/MP3playerinthe
dashaligningthemountingholeoftheCD/MP3playerwiththefactorymounting
brackets. Securetheradiotothebracketsusingfactorymountingscrews.
FACTORY SIDE RETAINING PLATES,
STYLE AND SHAPE WILL VARY
FOR EACH VEHICLE
Once the CD/MP3 player is
secured, insert the face plate
with the right side of the face
plate angled in first then gently
push the left side of face plate
until it snaps completely in place.
Table des matières
