PRO SIGNAL PSG3237 Manuel utilisateur
PSG3237
2 IN 1 WIRELESS AUDIO TRANSCEIVER
1
WHAT’s IN THE BOX
OVERVIEW
IMPORTANT SAFETY INFORMATION
INSTALLATION
• The transceiver can be used in three congurations:-
1. As a transmitter to connect signals from a wired source device to a remote wireless
equipped receiving device such as headphones.
2. As a receiving device to connect signals from a remote mobile wireless device to
wired destination equipment such as a Hi-Fi.
3. When used with a second transceiver unit, as a wireless connection between a
non wireless equipped wired source device, and a non wireless equipped wired
destination device.
• The red transmit/receive LED ashes slowly when the battery is getting low.
• The red LED illuminates during charging and extinguishes when the battery is fully
charged.
Please read these instructions carefully before use and retain for future reference.
Transmitting mode
• Connect one of the supplied connection cables (as required) into the ‘Transmit’ jack
and the other end to the source equipment output sockets.
• Power on the transceiver by pressing and holding the main button for approx 3
seconds.
• The red ‘transmit’ LED illuminates.
• The blue LED will ash rapidly to indicate it is in pairing mode.
On the source equipment search for RT-B6 and pair the devices
• Once connected the blue LED will ash slowly.
• When using electrical appliances basic safety precautions should always be followed.
• Do not expose the units to moisture or dust and excessive temperatures.
• Before use for the rst time, fully charge the internal battery using the supplied micro
USB cable powered from a mains adaptor or other USB 5VDC source.
2
• Wireless Transceiver
• USB Charging Cable
• Stereo 3.5mm jack to dual RCA phono lead
• Stereo 3.5mm jack to stereo 3.5mm jack lead
• User Manual
)))
Audio
Source
Transceiver Wireless
Receiving
Device
3
Receiving mode
• The Transceiver defaults to receive mode if no input or output leads are connected.
• Connect one of the supplied connection cables (as required) into the ‘Receive’ jack
and the other end to the destination equipment input sockets.
• Power on the transceiver by pressing and holding the main button for approx 3
seconds.
• The red ‘receive’ LED will be lit.
• The blue LED will ash rapidly to indicate it is in pairing mode.
• On the source equipment search for RT-B6 and pair the devices.
• Once connected the blue LED will ash slowly.
Note: Depending on the source device, you may set options for what functions are
connected to the transceiver.
Dual Device Transmit/Receive mode
• Connect one of the supplied connection cables (as required) into the ‘Transmit’ jack
on one transceiver device and the other end to the source equipment output sockets.
• Connect one of the supplied connection cables (as required) into the ‘Receive’ jack
on the second transceiver device and the other end to the source equipment output
sockets.
• Power on both transceivers by pressing and holding the main button for approx 3
seconds.
• The red ‘transmit’ LED illuminates on the rst transceiver and the red ‘receive’ LED
illuminates on the second.
• The blue LED will ash rapidly on both transceivers to indicate they are in pairing
mode.
• Once the connection is established the blue LEDs on both will ash slowly.
)))
)))
Audio
Source
Wireless
Audio
Source
Transceivers
Transceiver Receiving
Device
Receiving
Device
INFORMATION ON WASTE DISPOSAL FOR CONSUMERS OF ELECTRICAL &
ELECTRONIC EQUIPMENT.
When this product has reached the end of its life it must be treated as Waste Electrical & Electronic
Equipment (WEEE). Any WEEE marked products must not be mixed with general household waste,
but kept separate for the treatment, recovery and recycling of the materials used. Contact your local
authority for details of recycling schemes in your area.
Made in Taiwan. PR2 9PP
Man Rev 1.0
MAINTENANCE
• Clean the outside casing with a soft cloth lightly moistened with mild soap and water.
Never use any abrasive or solvents.
• Do not allow moisture to enter the devices.
SPECIFICATIONS
BT Version 2.1 low power (A2DP)
Supported Protocols A2DP, AVRCP, HFP, SPP HID
Current Consumption
<43mA (receiving mode)
<60mA (transmitting mode)
<18mA (standby mode)
Battery Polymer 400mAh
Charging current / time 300mA / 2hrs
Operating duration <8 hours
Wireless Range <10metres
Interface Micro USB for charging, 3.5mm stereo jack for signal
Compatibility All bluetooth audio devices (Smartphone, PC, MP3)
4
Table des matières
Autres manuels PRO SIGNAL Émetteur-récepteur
