Pro's Kit SS-611 Manuel utilisateur
SS-611 HEAT GUN SET
User’s Manual
1st Edition, 201
©2014 Copyright by Prokit’s Industries Co., Ltd.
Contents
Introduction.....................................................................................1
Description of symbols …..............................................................1
Specifications..................................................................................2
Understand your product...............................................................2
Setting up and Operation...............................................................3
Safety instructions..........................................................................4
Special safety instruction for heat gun.........................................7
Maintenance.....................................................................................8
Clean.................................................................................................8
General inspection….......................................................................8
Introduction
CAUTION. Read through this entire Instruction Manual before
using your new Power Tool. Take special heed of cautions and
warnings.
Description of symbols
Symbols shown on product sticker represent important information
about usage.
Wear ears protection.
Wear eyes protection.
Wear breath protection.
Dual-insulated for additional protection.
1
Specifications
SS-611A SS-611B SS-611H
Plug type A type I type H type
Nominal voltage 120V AC 60Hz 230V~240V AC 50Hz
Input power I: 750W / II: 1500W I: 750W / II: 1500W
Air volume I: 280 L/min II: 480 L/min I: 280 L/min II:480 L/min
Air temperature I: 300°C / II: 500°C I: 300°C / II: 500°C
Insulation class Double insulated
Overheat
Protection Please see page 7
Understand your product
Study the operating features and safety requirements at first before
using the heat gun. Use the tool and accessories only for the
application intended. Use tools only following instructions, prohibit
any usage out of the range
1. Motor housing
2. On/Off switch and temperature switch
3. Handle
Accessories
Contains:
If you find anything wrong, do not use the tool until
the parts have been replaced or the faulty has
been rectified. Failure to do so could result in
serious personal injury.
If any product defectiveness or missing parts was
found, please do not use it until the parts have
been replaced or the faulty has been rectified. Failure to do so could
result in serious personal injury.
2
3
Setting up and operation
The switch contains function of power on/off, temperature low/high.
The low temperature is roughly 300°C, and high temperature is
roughly 500°C.
• Always ensure the power switch is at off position before plugging in.
• Set power switch to I or II to heat one minute to reach its operation
temperature. Always wear protective gloves and eyes protection
when working.
• Place the heat gun upright on a flat table carefully.
• When operating a power tool outdoors, use an outdoor extension
cord suitable for outdoor use to reduce the risk of electric shock.
Paint and varnish removal
• Some test and technical training is required before removing
paint and varnish. Test on a small section of paint before
working on large areas.
• Turn on the heat gun to reach the full heating temperature. Hold
the nozzle 7.5cm to 10cm away from the painting area. After
heating a short while, the paint will soften and begin blistering.
• Do not overheat paint to avoid afire. Otherwise, this will cause
burning and make the finish more difficult to remove. When
striping paint on overhead, always wear eyes protection.
• Begin scraping the paint off downward, use accessory scrapers.
Scrape with smooth, even strokes, warming the surface in the
front of the scraper by moving the gun slightly from side to side.
If the paint is warmed properly, even thick layers can be
removed at once.
• Clean the paint from scraper as it is soft to prevent paint
building up on the blade, otherwise, it will quickly harden again.
• Shaped or uneven surfaces, clean with brush after softening
with the hot air jet.
• Cover the surfaces not to be cleaned with non-flammable
material. Never focalize tool’s heat on a window panel or other
glass surface.
NOTE: The Heat Gun Set is designed to remove both oil and
latex-based paint and vanish. It will not remove stains or primer
coats that have impregnated the surface of wood.
4
CAUTION: LEAD PAINT FUMES ARE VERY HARMFUL. ALWAYS
PROVIDE ADEQUATE VENTILATION WHILE WORKING INDOORS.
Other functions of the heat gun set
1. Remove paint and varnish.
2. Remove self adhesive stickers and trim.
3. Loosen rusted or over tightened nuts and metal screws.
4. Thaw frozen pipes, frozen door locks, padlocks, etc.
WARNING: DO NOT ATTEMPT TO THAW PLASTIC PIPS!
5. Pre-heat the natural wood grain of wooden surfaces before
staining or varnishing.
6. Dry paints and varnishes fast, this is especially useful when
adding several coats of the paint or varnish together.
7. Soften old putty before remove and replacement.
8. Drying wet and damaged timber before filling with compound
and refinishing.
9. Shrinking PVC shrink-wrap sheeting for packaging protection.
10. Shrinking polyvinyl wire joints.
Safety instructions
• The tool must be used only for the prescribed purpose. Any usage
other than those mentioned in this manual will be considered a
case of error operation. The user shall be liable for any damage or
injury resulted from such cases of misuse.
• To use this tool properly, you must observe the safety regulations,
the assembly instructions and the operation instructions to be
found in this Manual. Every person who use and service the
machine has to be acquainted with this manual and be informed
about its potential hazards. Children and infirm people are
prohibited to use this tool.
• Children in the working venue should be supervised at all time. It
is also imperative that you observe the accident prevention
regulations in force in your area. The same applies for general
rules of occupational health and safety.
• The manufacturer shall not be liable for any changes made to the
tool nor for any damage resulting from such changes.
WARNING! Before connecting a tool to a power source (main power
point receptacle, outlet, etc.), ensure that the voltage supply is the
5
same as that specified on the nameplate of the tool. A power source
with a voltage greater than that specified for the tool can result in
serious injury to the user, as well as damage to the. If in doubt, do not
plug in the tool. Using a power source with a voltage less than the
nameplate is harmful to the motor.
Even when the tool is used as prescribed; it is not possible to
eliminate all residual risk factors. The following hazards may arise in
connection with the tool’s construction and design.
WARNING! Read and understand all instructions. Failure to follow all
instructions listed below may result in electric shock, fire and /or
serious injury.
Relevant instructions
Work Area
1. Keep work area clean and in ordered. Cluttered and dark areas
invite accidents.
2. Do not operate power tools in explosive atmospheres, such as in
the presence of flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
3. Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
Electrical Safety
1. Power tool plugs must match the outlet. Never modify the plug in
any way. Do not use any adapter plugs with earthed (grounded)
power tools. Unmodified outlets will reduce risks of electric shock.
2. Guard against electric shock Prevent body contact with grounded
surfaces (e.g. pipes, radiators, ranges, refrigerators, etc.).
3. Do not expose power tools under rain or wet conditions. Water
entering a power tool will increase the risk of electric shock.
4. Do not abuse cord Never carry tool by cord or yank it to
disconnect it from wall outlet. Keep cord from heat, oil and sharp
edges. Damaged or entangled cords increase the risk of electric
shock.
5. When operating a power tool outdoors, use an outdoor extension
cord suitable for outdoor use to reduce the risk of electric shock.
6
Personal Safety
1. Stay alert, watch what you are doing when operating a power tool.
Do not use a power tool while you are tired or under the influence
of drugs, alcohol, or medication. A moment of inattention while
operating power tools may result in serious personal injury.
2. Use safety equipment. Always wear eye protection. Safety
equipment such as a dust mask, non-skid safety shoes, hard at, or
hearing protection used for appropriate condition will reduce
personal injuries.
3. Avoid accidental starting. Ensure the switch is in the off-position
before plugging in. Carrying power tools with your finger on the
switch or plugging in power tools that have the switch on invites
accidents.
4. Remove any adjusting key or wrench before turning the tool on. A
wrench or a key that is left attached to rotating part of the power
tool may result in personal injury.
5. Do not overreach. Keep proper footing and balance at all times.
This enables better control of the power tool in unexpected
situations.
6. Dress properly. Do not wear loose clothing or jewelry. Keep your
hairs, clothing and gloves away from moving parts .Loose cloths,
jewelry or long hairs can be caught in moving parts.
7. If devices are provided for the connection of dust extraction and
collection facilities ensure that these are connected and properly
used. Used of these devices can reduce dust-related hazards.
Power Tool Use and Care
1. Use the correct power tool under designed working range, it
makes your the job done better and safer.
2. Do not use the power tool if the switch is not functional. Any power
tool that cannot be controlled with the switch is dangerous and
must be repaired.
3. Disconnect the plug from the power source before making any
adjustments, changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the power
tool accidentally.
4. Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to
operate the power tool. Power tools are dangerous in the hands of
untrained users.
5. Maintain power tools. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect
the power tool’s operation. If damaged, have the power tool
repaired before use. Many accidents are caused by poorly
maintained power tools.
6. Use the power tool, accessories and tool bits etc., in accordance
with these instruction and in the manner intended for the particular
type of power tool, taking into account the working condition and
the work to be performed .Use of the power tool for operations
different from intended could result in a hazardous situation.
Special safety instruction for heat gun
Overheat protection
If this product is overheating, the heater will stop heating up
automatically and cool air blowing constantly to reduce waiting time
from heater restarting
CAUTION:
Never put the appliance down on its air outlet nuzzle. Always keep its
outlet nuzzle upward or put it on one of its sides to prolong the service
lifetime.
WARNING! The use of accessories or attachment, other than those
recommended in this instruction manual, may present a risk of
personal injury.
Additional safety instruction for heat guns
1. Fully unwind cable drum extensions to avoid potential overheating.
2. Avoid instant switch between power and temperature to secure
the using life of heater and switch control. Heater is consumable
accessory.
7
3. When an extension cable is required, you must ensure that it has
the right ampere rating for you power tool and is in safe electrical
8
condition.
Always switch off before you put the heat gun down. 4.
5. Do not let anyone under 18 years operate this tool.
e 6. Rags, cloths, cord, string and the like should never b left around
the work area.
7. If you are interrupted when operating the tool, complete the
process and switch off before looking up.
8. Do not block the air inlet or outlets.
materi9. Do not use in proximity to flammable als.
Maintenance
There are no serviceable parts, no maintenance is required.
place, the task must be carried out by
Gener no damage to the heat gun.
Power cord maintenance
If the supply cord needs to re
the manufacturer, the manufacturer’s agent, or an authorized service
centre in order to a safety hazard.
Cleaning
1. Keep the tool’s air vents unclogged and clean at all times.
2. Remove dust and dirt regularly .Cleaning is best done with a rag.
Wear safety goggles or an eye shield and gloves whist cleaning.
3. Never use caustic agents to clean plastic parts.
commended. CAUTION. A mild detergent on a damp cloth is re
Water must never come into contact with the tool.
al inspection
Regularly check that there is
目錄
介紹.................................................................................................................9
符號涵義.........................................................................................................9
產品規格........................................................................................................10
瞭解產品........................................................................................................10
配置與使用....................................................................................................11
安全指示........................................................................................................12
專門針對熱風槍的安全指示......................................................................14
護保養/清潔/一般檢查.................................................................................15
介紹
注意!使用電動工具前請仔細閱讀整份使用說明書，嚴格遵循警示和注意
事項的說明。本工具有許多特性,這將使您的工作快捷、安全性、性能和
可靠性是本機設計製造中的首要問題，這使得產品易於操作和維護。
符號涵義
產品銘牌上可能出現的標誌，表示在產品使用中的一些重要資訊。
帶上耳塞保護聽力
帶上眼鏡保護眼睛
帶上口罩以免吸入有害氣體或粉塵
雙絕緣保護
9
Ce manuel convient aux modèles suivants
3
Table des matières
Autres manuels Pro's Kit Outils électriques
Pro's Kit
Pro's Kit SS-331B Manuel utilisateur
Pro's Kit
Pro's Kit SS-615 Series Manuel utilisateur
Pro's Kit
Pro's Kit SS-612A Manuel utilisateur
Pro's Kit
Pro's Kit PT-1801 Manuel utilisateur
Pro's Kit
Pro's Kit SS-611A Manuel utilisateur
Pro's Kit
Pro's Kit SS-628 Series Manuel utilisateur
Pro's Kit
Pro's Kit SS-979 Manuel utilisateur
Pro's Kit
Pro's Kit SI-168U Manuel utilisateur
Pro's Kit
Pro's Kit PT-0721 Manuel utilisateur
Pro's Kit
Pro's Kit SI-B166 Manuel utilisateur
Pro's Kit
Pro's Kit HT-5501 Manuel utilisateur
Pro's Kit
Pro's Kit PT-5208U Manuel utilisateur
Pro's Kit
Pro's Kit PT-1210 Manuel utilisateur
Pro's Kit
Pro's Kit SI-168U Manuel utilisateur
Pro's Kit
Pro's Kit SI-137 Manuel utilisateur
Pro's Kit
Pro's Kit PT-1805 Manuel utilisateur
Pro's Kit
Pro's Kit GS-23K Manuel utilisateur
Pro's Kit
Pro's Kit PT-1207 Manuel utilisateur
Pro's Kit
Pro's Kit Pro'sKt SS-621 Series Manuel utilisateur
Pro's Kit
Pro's Kit PT-1806 Manuel utilisateur
