Pro-face FP5000 Series Manuel utilisateur

FP5000 Series

User Manual

FP5000-MM01-EN-PDF_02

The information provided in this documentation contains general descriptions and/or technical

characteristics of the performance of the products contained herein. This documentation is not

intended as a substitute for and is not to be used for determining suitability or reliability of these

products for specific user applications. It is the duty of any such user or integrator to perform the

appropriate and complete risk analysis, evaluation and testing of the products with respect to the

relevant specific application or use thereof. Neither Schneider Electric nor any of its affiliates or

subsidiaries (hereinafter, referred to as Schneider Electric) shall be responsible or liable for misuse

of the information that is contained herein. If you have any suggestions for improvements or

amendments or have found errors in this publication, please notify us.

You agree not to reproduce, other than for your own personal, noncommercial use, all or part of

this document on any medium whatsoever without permission of Schneider Electric, given in

writing. You also agree not to establish any hypertext links to this document or its content.

Schneider Electric does not grant any right or license for the personal and noncommercial use of

the document or its content, except for a non-exclusive license to consult it on an "as is" basis, at

your own risk. All other rights are reserved.

All pertinent state, regional, and local safety regulations must be observed when installing and

using this product. For reasons of safety and to help ensure compliance with documented system

data, only the manufacturer should perform repairs to components.

When devices are used for applications with technical safety requirements, the relevant

instructions must be followed.

Failure to use Schneider Electric software or approved software with our hardware products may

result in injury, harm, or improper operating results.

Failure to observe this information can result in injury or equipment damage.

FP5000 Series User Manual

Table of Contents

Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

About the Book. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Chapter 1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Model Number Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Model Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Revision. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Certifications and Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Federal Communication Commission Radio Frequency Interference

Statement - For U.S.A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Hazardous Location Installation - For USA and Canada. . . . . . . . . . . 19

European (CE) Compliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

KC Markings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Chapter 2 Device Connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

System Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Chapter 3 Parts Identification and Functions . . . . . . . . . . . . . . . . 27

FP-5600TPD/5700TPD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

LED Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Chapter 4 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

4.1 General Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Electrical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Structural Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

4.2 Functional Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Display Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Touch Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

4.3 Interface Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Interface Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Interface Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

DVI-D Input Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Chapter 5 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

FP-5600TPD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

FP-5700TPD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Chapter 6 Installation and Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . 53

6.1 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Installation Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

6.2 Wiring Principles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Connecting the DC Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Connecting the Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

6.3 USB Cable Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

USB Clamp (Type B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

6.4 Front USB Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Opening the Front USB Cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Chapter 7 System Specifications and Launcher. . . . . . . . . . . . . . 73

7.1 System Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Operating System, Drivers, Utilities. . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Settings Workflow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Installing the Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Installing the Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

7.2 Launcher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

About the Launcher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Display Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

PC Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Chapter 8 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Regular Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Periodic Check Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Replacing the Installation Gasket . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

Replacing the Backlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

Troubleshooting Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

After-sales Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

FP5000 Series User Manual

Safety Information

Important Information

NOTICE

Read these instructions carefully, and look at the equipment to become familiar with the device

before trying to install, operate, or maintain it. The following special messages may appear

throughout this documentation or on the equipment to warn of potential hazards or to call attention

to information that clarifies or simplifies a procedure.

PLEASE NOTE

Electrical equipment should be installed, operated, serviced, and maintained only by qualified

personnel. No responsibility is assumed by Schneider Electric for any consequences arising out of

the use of this material.

A qualified person is one who has skills and knowledge related to the construction and operation

of electrical equipment and its installation, and has received safety training to recognize and avoid

the hazards involved.

FP5000 Series User Manual

About the Book

At a Glance

Document Scope

This manual describes how to use this product.

Validity Note

This documentation is valid for this product.

The technical characteristics of the device(s) described in this manual also appear online at

http://www.pro-face.com.

The characteristics presented in this manual should be the same as those that appear online. In

line with our policy of constant improvement we may revise content over time to improve clarity and

accuracy. In the event that you see a difference between the manual and online information, use

the online information as your reference.

Registered Trademarks

Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States

and/or other countries.

Product names used in this manual may be the registered trademarks owned by the respective

proprietors.

Related Documents

You can download the manuals related to this product, such as the software manual, from our

support site at http://www.pro-face.com/trans/en/manual/1001.html.

Product Related Information

Critical alarm indicators and system functions require independent an redundant protection

hardware and/or mechanical interlocks.

When you cycle power, wait at least 10 seconds after it has been turned off. If this product is

restarted too quickly, it may not operate correctly.

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

Remove all power from the device before removing any covers or elements of the system, and

prior to installing or removing any accessories, hardware, or cables.

Unplug the power cable form both this product and the power supply.

Always use a properly rated voltage sensing device to confirm power is off.

Replace and secure all covers or elements of the system before applying power to this

product.

This product uses 12 to 24 Vdc power. Using any other level of power can damage both the

power supply and this product.

Failure to follow these instructions will result in death or serious injury.

In the event the screen cannot be properly read, for example, if the backlight is not functioning, it

may be difficult or impossible to identify a function. Functions that may present a hazard if not

immediately executed, such as a fuel shut-off, must be provided independently of this product. The

machine’s control system design must take into account the possibility of the backlight no longer

functioning and the operator being unable to control the machine or making mistakes in the control

of the machine.

For additional information, refer to NEMA ICS 1.1 (latest edition), "Safety Guidelines for the

Application, Installation, and Maintenance of Solid State Control" and to NEMA ICS 7.1 (latest

edition), "Safety Standards for Construction and Guide for Selection, Installation and Operation of

Adjustable-Speed Drive Systems" or their equivalent governing your particular location.

WARNING

LOSS OF CONTROL

The designer of any control scheme must consider the potential failure modes of control paths

and, for certain critical control functions, provide a means to achieve a safe state during and

after a path failure. Examples of critical control functions are emergency stop and overtravel

stop, power outage and restart.

Separate or redundant control paths must be provided for critical control functions.

System control paths may include communication links. Consideration must be given to the

implications of unanticipated transmission delays or failures of the link.

Observe all accident prevention regulations and local safety guidelines.

Each implementation of this product must be individually and thoroughly tested for proper

operation before being placed into service.

The machine control system design must take into account the possibility of the backlight no

longer functioning and the operator being unable to control the machine, or making errors in

the control of the machine.

Failure to follow these instructions can result in death, serious injury, or equipment

damage.

WARNING

UNINTENDED EQUIPMENT OPERATION

The application of this product requires expertise in the design and programming of control

systems. Only persons with such expertise should be allowed to program, install, alter, and apply

this product.

Follow all local and national safety standards.

Failure to follow these instructions can result in death, serious injury, or equipment

damage.

FP5000 Series User Manual

The following characteristics are specific to the LCD panel and are considered normal behavior:

LCD screen may show unevenness in the brightness of certain images or may appear different

when seen from outside the specified viewing angle. Extended shadows, or crosstalk may also

appear on the sides of screen images.

LCD screen pixels may contain black and white colored spots and color display may seem to

have changed.

When the same image is displayed on the screen for a long period, an afterimage may appear

when the image is changed.

The panel brightness may decrease when used for a long time in an environment continuously

filled with inert gas. To prevent deterioration of panel brightness, regularly ventilate the panel.

For more information, please contact customer support.

http://www.pro-face.com/trans/en/manual/1015.html



NOTE: Change the screen image periodically and try not to display the same image for a long

period of time.

WARNING

UNINTENDED EQUIPMENT OPERATION

Do not use this product as the only means of control for critical system functions such as motor

start/stop or power control.

Do not use this equipment as the only notification device for critical alarms, such as device

overheating or overcurrent.

Use only the software provided with this product. If you use another software, please confirm

the operation and safety before use.

Failure to follow these instructions can result in death, serious injury, or equipment

damage.

CAUTION

SERIOUS EYE AND SKIN INJURY

The liquid in the LCD panel contains an irritant:

Avoid direct skin contact with the liquid.

Wear gloves when you handle a broken or leaking unit.

Do not use sharp objects or tools in the vicinity of the LCD panel.

Handle the LCD panel carefully to prevent puncture, bursting, or cracking of the panel material.

If the panel is damaged and any liquid comes in contact with your skin, immediately rinse the

area with running water for at least 15 minutes. If the liquid gets in your eyes, immediately rinse

your eyes with running water for at least 15 minutes and consult a doctor.

Failure to follow these instructions can result in injury or equipment damage.

Table des matières

Autres manuels Pro-face PC industriel

Pro-face

Pro-face GP2500-TC11 Manuel utilisateur

Pro-face

Pro-face GP-4402WW Manuel utilisateur

Pro-face

Pro-face PS-3650A Series Manuel utilisateur

Pro-face

Pro-face PS3700A-T41-ASU-P41 Manuel utilisateur

Pro-face

Pro-face PS3700A-T41-ASU-E66 Manuel utilisateur

Pro-face

Pro-face GP-4311HT Manuel utilisateur

Pro-face

Pro-face PS-4600 Series Manuel utilisateur

Pro-face

Pro-face PL-B910 Series Manuel utilisateur

Pro-face

Pro-face GP2000 Series Manuel utilisateur

Pro-face

Pro-face GP-477R Series Manuel utilisateur

Pro-face

Pro-face PL-B910 Series Manuel utilisateur

Pro-face

Pro-face PS400G-T41-E124V Manuel utilisateur

Pro-face

Pro-face PS5000 Series Manuel utilisateur

Manuels PC industriel populaires d'autres marques

Chipsee

Chipsee PPC-A72-101 Manuel utilisateur

Advantech

Advantech UNO-2184G Manuel utilisateur

MSI

MSI MS-9A76 Manuel utilisateur

Stackrack

Stackrack THOR200 Manuel utilisateur

Moxa Technologies

Moxa Technologies DA-682C Series Manuel utilisateur

Nodka

Nodka eBOX-3000-ETC Manuel utilisateur

Siemens

Siemens SIMATIC IPC627E Manuel utilisateur

MSI

MSI MS-9A89 Manuel utilisateur

Artila

Artila Matrix-516 Manuel utilisateur

Siemens

Siemens SIMATIC Rack PC 840 V2 Manuel utilisateur

Advantech

Advantech IPPC-6152A Manuel utilisateur

Beckhoff

Beckhoff CX9020 Manuel utilisateur

Dell

Dell Embedded Box PC 5000 Manuel utilisateur

IBASE Technology

IBASE Technology ASB200-918 Series Manuel utilisateur

Lenovo

Lenovo ThinkCentre M90q Manuel du propriétaire

IXXAT

IXXAT Econ 100 Manuel utilisateur

Kontron

Kontron KBox A-151-TGL Manuel utilisateur

AXIOMTEK

AXIOMTEK ICO500-518 Series Manuel utilisateur