Priolite MBX 500 HotSync Manuel utilisateur

Instruction manual PRI

LITE MBX 500 - HotSync

PRI

LITE GmbH Wuerzburg - Last revised: 12/2013 - Page 12

Contact information.

PRI

LITE GmbH

Gattingerstr. 7

D-97076 Würzburg

Germany

Phone: +49 (0)931 20700000

E-mail: [email protected]

Internet: http://www.priolite.com

.Declaration of Conformity.

The company PRI

LITE GmbH

Gattingerstr. 7, D-97076 Würzburg, Germany

declares that the products

MBX 500 - HotSync

are in conformity with the following standards:

EN 61000-6-3:2007, EN 61000-6-2:2005 and DIN EN 60335

according to the provisions of the Directives

2004/108/EG and 2006/95/EG

Place and date of issue:

Würzburg, 02-December-2013

Dipl.-Ing. Joachim Renschke

Managing Director PRI

LITE GmbH

PRI

LITE GmbH / Gattingerstr. 7 / D-97076 Würzburg / Tel +49(0)931 20700000 / eMail in[email protected] / http://www.priolite.com

Instruction manual

MBX 500 - HotSync

Instruction manual PRI

LITE MBX 500 - HotSync

PRI

LITE GmbH Wuerzburg - Last revised: 12/2013 - Page 2

Introduction.

Dear photographer,

Thank you for selecting the PRI

LITE compact flash unit.

As a young, aspiring company, PRI

LITE intends to use innovative technologies and high-

quality products to open up new market segments for professional photography.

Our devices are based on state-of-the-art technology and equipped with carefully selected

components. Our production process is continuously monitored to ensure high quality and

safety standards.

Before using this unit, please read the operating manual and safety instructions carefully to

prevent damage to the device and maintain your warranty.

We wish you many successful years of productive and innovative work with our equipment.

Should you have questions about our products, please contact us!

Best regards,

PRI

LITE GmbH

Description.

The PRI

LITE MBX 500-HotSync is a radio-controllable, battery-operated compact unit

with an exchangeable battery; the power output ranges from 16J to a maximum of 500J

covering 6 f-stops precisely adjustable in 1/10 increments. The flash recycle time to

maximum output is around 2.8 seconds. The modelling lamp for MBX 500 is a LED array.

MBX 500-HotSync is optimized for flash synchronisation up to 1/8000 sec. Therefore, it

provides a long and constant flash duration of 1/200 sec. HotSync function is only usable in

combination with the Priolite Remote Control RC-HS (see the instruction manual).

MBX 500 - HotSync can also be triggered from other sources, but in this case, the flash

sync time is limited to 1/200 sec.

Delivery includes.

1 compact flash PRI

LITE MBX 500-HotSync; 1 multi-voltage battery charger 16V; 1 flash-

tube 500J for plug-in; 1 built-in LED array as modelling lamp; 1 protection glass dome; 1

tilting head; 1 synchronization cable; 1 black plastic protective cap for safe transportation.

MBX 500-HotSync series is also available as a kit which includes only one synchronization

cable and one cableset to connect the remote control with the camera. There is also only

one battery charger per kit supplied.

For the composition of the kits, please refer to our currently valid price-list.

Instruction manual PRI

LITE MBX 500 - HotSync

PRI

LITE GmbH Wuerzburg - Last revised: 12/2013 - Page 11

Maintenance.

Before maintenance are to be done, the following safety precautions must be strictly

observed:

Before replacing the flash tube or the modeling light, the flash unit must be switched

off. Then you must wait at least 5 minutes for safety reasons to ensure the complete

discharge of the capacitors via the internal safety circuit. Furthermore, before

replacing the flash tube, you must wait until it has cooled down.

To remove the glass dome, please refer to the instructions described above. The

flash tube and modelling lamp must not be touched during this procedure (danger!).

Always use extreme caution when handling an exposed flash tube due to the

existing overpressure.

If the glass of the flash tube is broken, do not touch the electrodes in any case when

you are replacing the flash tube! In this case you must use fully insulated pliers to

remove the damaged flash tube!

Replacement of flash tubes

For replacement pull the flash tube carefully out of the plug connector and replace it with a

new one (to be ordered from PRI

LITE) by plugging the three contacts into the sockets.

Before using the unit once again the glass dome is to be mounted for safety reasons.

Regular inspection and repairs

Except for the work described in the “Maintenance” section, users may not perform any

repairs on flash systems; these are to be carried out exclusively by authorized customer

service personnel.

In accordance with country-specific safety regulations, inspection and maintenance of

electrical systems and devices should be carried out at regular intervals. We recommend an

annual inspection of the units to ensure operational safety and reliability and to maintain the

value of the system.

Return to customer service

To prevent damage during transport and to ensure optimal protection of the units, we

recommend to ship the devices only in the original packaging.

Disposal

Disused and defective units must be disposed of in the electronic recycling.

.Accessories.

The following accessories are available:

Radio remote control RC-HS, textile & metal lightformers of different shapes and sizes

(reflectors, grids, softboxes, octaforms, striplights, umbrellas), stands, cases & bags, glass

domes, flashtubes, cables, multivoltage chargers, and battery exchange drawers.

Instruction manual PRI

LITE MBX 500 - HotSync

PRI

LITE GmbH Wuerzburg - Last revised: 12/2013 - Page 10

Flash triggering .

Flashes can be triggered as follows:

Flash triggering via the synchronization cable

The compact flash unit is connected to the camera using a synchronization cable with a 3.5

mm phone jack via the synchronization socket. The synchronization socket is located

besides the photocell in the area of the handle. The synchronization voltage is 5 V.

The synchronization circuit was designed using state-of-the-art semiconductor technology.

This enables reliable flash triggering even in older cameras with mechanical contacts.

However, due to the large number of different electronic circuits used in the cameras for

synchronization control, we cannot assume any liability for any damage to the camera by

triggering the flash. You should therefore contact the camera manufacturer before using

cameras that are not generally commercially available.

Flash triggering via the photocell

The compact flash unit can also be triggered via the built-in photocell. Triggering then

occurs when a flash from another unit “strikes” the first unit. This operating mode is

activated by pressing the Slave button (control LED is on).

The photocell is designed as an impulse photocell. Thus, it works only when the striking

flash has a higher aperture value than the ambient light. You must therefore ensure that no

excessively strong external light falls on the photocell. If this cannot be avoided, another

method of flash triggering must be selected.

Flash triggering via radio remote control

The compact flash unit is equipped with a built-in bi-directional radio module. To trigger the

flash via radio, the radio remote control must be mounted onto the hot shoe of the camera

and then switched on using its main switch. You must also ensure that the TEAM/ID

settings on the radio module and the flash unit match. The flash is triggered by activating

the camera shutter.

Flash triggering via the TEST button

The flash can also be manually triggered by pressing the “TEST” button.

Automatic Power Drop (APD)

If the power setting is reduced, the stored energy is internally dissipated. During this

process no flash will be triggered. Compact flash units that are switched off are

automatically discharged. It is also possible to reduce the energy quickly to the current

value by triggering a test flash.

Instruction manual PRI

LITE MBX 500 - HotSync

PRI

LITE GmbH Wuerzburg - Last revised: 12/2013 - Page 3

Intended use.

This compact flash unit is intended for mobile use in professional photography in the studio

or on location. Its purpose is the provision of electrical power for flash generation and flash

generation itself. The unit may not be used for any other purpose.

Compact flash units store energy in capacitors by collecting high voltages, which

creates particular sources of danger. Before using this unit, read and comply the

following safety instructions.

Safety instructions.

 Flash units may not be operated without supervision.

 Always use extreme care when handling the flash unit to prevent damage to the flash

tube. A damaged flash tube poses a risk of severe injury or death, as you can come into

contact with the voltage-carrying electrodes. If this happens, the unit must be switched

off immediately. For safety reasons, before exchanging the flashtube you must wait at

least 5 minutes after switching off the unit to ensure that the capacitors have completely

discharged via the internal safety circuit. The same applies to any type of maintenance

work or before transports, which may be undertaken on the unit only when it has been

switched off and after the waiting period has expired.

Contact with the capacitor voltage is life-threatening; thus, the opening of the casing and

repairs on the compact unit may be carried out only by authorized customer service

personnel.

Only the original PRI

LITE charger may be used for charging the batteries. Before

each use, check to ensure that the casing as well as all cables, connectors and sockets

are in good, undamaged condition. Otherwise operation of this device is forbidden;

damaged units and/or cables must only be repaired or replaced by authorized customer

service personnel.

Flash units may be operated only with a properly mounted glass dome, as flash tubes

can explode due to the development of overpressure.

It is particularly important to protect the flash unit from moisture, splash water and

impacts during use or transport. This unit is not designed for operation in dusty

environments. Flash systems may not be used in potentially explosive areas; to prevent

the risk of fire, do not store flammable materials (e.g. decorative materials, paper, etc.)

in the immediate vicinity of the flash units.

 Do not insert any objects into the ventilation slots or the charging or synchronization

sockets. The ventilation slots must be kept clear during operation.

Flash units mounted on pantographs or ceiling systems must be doubly secured against

falling down.

Instruction manual PRI

LITE MBX 500 - HotSync

PRI

LITE GmbH Wuerzburg - Last revised: 12/2013 - Page 4

Do not flash into eyes from a short distance (less than 5 meters) as this can cause injury

to your eyes. Do not look directly into the flash reflector; the flash could be inadvertently

triggered.

Ventilate closed rooms regularly to prevent illegal ozone levels, which can be generated

by the use of high-performance flash units.

Specific safety precautions when working with Lithium-ion batteries.

The provided Lithium-ion battery contains a protection circuit that protects the battery

against overload, deep discharge, short circuit and overheating.

In case of improper use (cutting, breaking, overheating) the batteries can explode or cause

fires, even after a prolonged time interval. Therefore, Lithium-ion batteries are generally to

be protected from mechanical damage and kept away from heat, open flames, and

corrosive liquids. Batteries must not be damaged in any way. Lithium cells generally

respond violently with water (particularly in fully charged condition); therefore, in case of

burning do not extinguish the flames with water, but use sand. Damaged Lithium-ion

batteries are readily to be disposed of in appropriate containers.

Lithium-ion batteries contain flammable and / or corrosive solutions and Lithium salts, which

may cause in the case of leakage irritation to skin, eyes, and mucous membranes. In case

of contact with escaped electrolytes, gases, or fire by-products of a Lithium-ion battery, the

following first aid measures must be observed:

Eyes: In case of contact with eyes, rinse immediately for at least 15 minutes with water.

Keep eyelids open in order to ensure the complete flushing of the eye.

Skin: Take off contaminated clothing and rinse under cold water for at least 15 minutes.

Respiratory system: Ensure fresh air supply. If necessary, perform first aid measures.

In any case, following first aid measures a doctor should be consulted.

Lithium-ion batteries must be only recharged with the supplied PRI

LITE charger of the

respective voltage class; use the 16V charger for MBX 500.

The charge should be performed only under supervision and not in close proximity to

combustible materials; sufficient dissipation of heat must be provided (do not charge the

battery in the sun).

If a Lithium-ion battery is carried on air travel, then it must be discharged prior to departure

to avoid any risks.

Instruction manual PRI

LITE MBX 500 - HotSync

PRI

LITE GmbH Wuerzburg - Last revised: 12/2013 - Page 9

PILOT function box (modelling lamp)

The modelling lamp is switched on or off using the “PILOT” buttons.

MBX 500 is equipped with a LED array as modelling lamp; the light output is equivalent to

that of an 80W halogen lamp. It always lights up with maximum power and is not dimmable.

The mode FREE and PROP is not available.

Bear in mind that longer operation of the modelling lamp consumes battery capacity

which is then no longer available for the flash. Therefore, it is advised to limit the

operation time with the pilot light switched on.

RADIO function box (radio operation)

For remote radio operation, use the three radio buttons on the right.

ON:

If the ON button is activated (control LED lights up), the flash can be triggered and

controlled by radio. Additional entries for TEAM and ID are required.

Team/ID:

Selection of a team (A, B, or C) or an ID (1 to 9) is done by pressing the Team or the ID

button, resp., and simultaneously turning the control knob until the desired selection is

indicated on the LED display. By adjusting all possible combinations, a maximum of 27

flash units (3x9) can be individually triggered and controlled.

Team and ID can be changed only when the radio function is “ON”.

AUXILIARIES function box (additional functions)

Slave:

If the “Slave” button is activated, an external flash is triggered via the photocell (see the

section entitled “Flash triggering” below).

FC:

IF FC (Flash Check) is activated, the modelling lamp goes off immediately after the flash

has been released and lights up again only after the unit has charged up to the selected

level. This ensures correct charging as well as renewed flash readiness. The flash control

ensures that the flash lamps light up when several flash units are used.

Audio:

If the “Audio” button is activated, flash readiness is indicated by an acoustic signal.

Test

Test flashes can be released by pressing the “TEST” button.

For additional flash triggering options, please refer to the next section.

Flash readiness

Flash readiness is indicated by 1.) lighting up of the “TEST” button; 2.) green light of the

plastic cap covering the photocell; 3.) re-lighting up of the modelling lamp when FC is

activated; and 4.) an acoustic signal when the Audio function is switched on.

Instruction manual PRI

LITE MBX 500 - HotSync

PRI

LITE GmbH Wuerzburg - Last revised: 12/2013 - Page 8

Replacement of battery drawers and connection to the charger

To replace the battery, please proceed as follows: Before exchanging the drawer the device

is to be switched off by using the main switch protected by a flap; the green LED light

located on the left side of the main switch goes off. Then, place your index finger into the

pull-out handle and press your thumb against the bottom flap of the battery drawer. With

combined upward push and pull, the drawer is to be completely removed out of the housing

of the flash unit.

With the battery drawer pulled out of the unit, under no circumstances reach into

the opening of the compact flash device!

An exchange drawer fitted with an original PRI

LITE battery of the same voltage class

(MBX 500: 500V) is to be inserted completely into the opening of the flash unit with slight

pressure until it clicks.

The charging of the battery can be done inside the flash unit (switched on or off) or outside

of the housing. The charging cable of the supplied charger (16V) is plugged into the

charging socket of the battery drawer and the provided power cable connected to the mains

outlet. The charging unit is intended for global supply voltages (multivoltage: 230V/115V).

The charging time of a flat battery to full charge is approximately 3 hours. Full charge is

indicated by the lighting up of all 5 LEDs.

The batteries for PRI

LITE flash units are of different sizes and weights; in addition,

chargers are also fitted with a different charging plugs. Therefore, please make sure, that

for operation with MBX500-HotSync the correct size of the battery is inserted and the 16V

charger with the 2-pin charging plug is in use.

Functions on the operating panel.

Control knob

The control knob is used to set the desired flash power in 1/10 increments from 500J to a

minimum of 16J covering 6 f-stops for MBX 500. The output is displayed on the two-digit 7-

segment display in f-stops: 10 stands for maximum power and 5.0 for minimum power.

Increasing or decreasing the f-stop by 1.0 point doubles or halves the flash output, rsp.

MBX 500-HotSync operating panel

From right to left and top to buttom:

PILOT function box (modelling lamp options)

2-digit LED display

Turning knob

Battery drawer with

> Mains switch behind the flap,

> Pull-out handle and upper/lower flap,

> Charging socket and

> row of LEDs for charging control (top left)

RADIO function box (options for remote control)

1-digit LED-display

Flash release button (TEST)

AUXILIARIES function box (Slave, FC, Audio)

Instruction manual PRI

LITE MBX 500 - HotSync

PRI

LITE GmbH Wuerzburg - Last revised: 12/2013 - Page 5

Technical data MBX 500 - HotSync .

Output: 500 Ws

Voltage supply: Lithium-ion battery with protection circuit, no

Memory ffect, 16V, 35 Wh, weight approx. 600 g

Modelling lamp: LED array, equivalent to 80W halogen

Flash recycle time: 2.8 sec. at full power

Fastest flash sequence: 2 flashes per second

Flash duration t0.5 (sec): 1/4500 at full power

Color temperature (K): 5500

f-stop (1m distance, 7”reflector, 64,2

ISO100, measuring time 1/125)

shortest sync time: up to 1/8000 sec. depending on the camera

Sync voltage: 5V for safe flash triggering by modern digital cameras.

socket for 3.5 mm phone jack

Flash power control: 1/10 increments, over 6 f-stops

10 = full power (500 Ws), 5 = min. power (16 Ws)

No. of flashes/charge: 220/full power (display ‘10’), 440/250 Ws (display ‘9’)

more than 6000 at low power

Charger: 16V (Multivoltage)

Charging time: approx. 2h to 80% and approx. 3h to full charge

Weight (without tilt): 3,2 kg (battery included)

Dimensions (cm x cm): 40 x 17

Code No.: 01-0500-04

Initial operation.

Set-up and assembly

The compact flash units are equipped as standard with a tilting head. For set-up on

tripods, pantographs or ceiling systems, the tilt is screwed securely onto the

appropriate tripod mount using the locking thumbscrew on the side of the panner.

If the unit is suspended from a pantograph or ceiling rail during operation, a second

secure connection is required in accordance with the applicable safety regulations. It

is recommended to insert a steel cable suitable for this purpose (not included)

through the opening of the handle and to secure it to a suitable lug on the

suspension unit.

Autres manuels Priolite Flash de l'appareil photo

Priolite

Priolite M500 Manuel utilisateur

Manuels Flash de l'appareil photo populaires d'autres marques

Canon

Canon 5246B002 Manuel utilisateur

Sigma

Sigma EF-610 DG SUPER - Manuel utilisateur

Godox

Godox DP300 Manuel utilisateur

Sony

Sony HVL-FDH4 Manuel utilisateur

Sony

Sony HVL-RLA Manuel utilisateur

Nikon

Nikon SB-28 Manuel utilisateur

Canon

Canon Speedlite 380EX Manuel utilisateur

Olympus

Olympus FL 36R Manuel utilisateur

Nikon

Nikon BC-7 Manuel utilisateur

Altura Photo

Altura Photo AP-305N Manuel utilisateur

Nikon

Nikon SB-800 Manuel utilisateur

DÖRR

DÖRR DFX-300 Manuel utilisateur

Canon

Canon SPEEDLITE 300EZ Manuel utilisateur

Sunpak

Sunpak 622 Super Pro-System Manuel utilisateur

Polaroid

Polaroid PL108-AF Manuel utilisateur

Godox

Godox Thinklite TT350P Manuel utilisateur

Pentax

Pentax AF240Z Manuel utilisateur

Pixapro

Pixapro Li-ion 350 II N Manuel utilisateur