Priolite M-PACK 500 Manuel utilisateur

PRI

LITE GmbH / Gattingerstr. 7 / D-97076 Würzburg / Tel +49(0)931 20700000 / eMail in[email protected] / http://www.priolite.com

Instruction manual

PACK

(HS)

+ PRIO HEAD

PACK

(HS)

+ PRIO HEAD

Instruction manual PRI

LITE M-PACK 500 / M-PACK 1000 (HS) + PRIO HEAD 1000

PRI

LITE GmbH Wuerzburg - Last revised: 08/2014 - Page 2

USER MANUAL.

Technical data are subject to change. No guarantee for misprints. The listed values are

guide values and should not be understood as binding in a legal sense. The values can

differ due to tolerances in used components.

Instruction manual PRI

LITE M-PACK 500 / M-PACK 1000 (HS) + PRIO HEAD 1000

PRI

LITE GmbH Wuerzburg - Last revised: 08/2014 - Page 3

Table of contents.

Introduction..................................................................................................................4

Description ..................................................................................................................4

Standard delivery ........................................................................................................4

Intended use................................................................................................................5

Safety instructions.......................................................................................................5

Specific safety precautions when working with Lithium-ion batteries ..........................6

Technical data power pack..........................................................................................7

Technical data flash head............................................................................................8

Initial operation............................................................................................................8

Set-up and assembly.............................................................................................8

Adjustment of the tilting head.................................................................................8

Attachment and removal of the glass dome before operating flash heads.............9

Mounting of accessories to flash heads.................................................................9

Connection of reflectors to flash heads..................................................................9

Connection of softboxes to flash heads...............................................................10

Umbrella attachment to flash heads ....................................................................10

Acclimatizing........................................................................................................10

Overheating.........................................................................................................10

Starting-up...........................................................................................................10

Replacement of the battery drawer......................................................................11

Connection to the charger....................................................................................12

Functions on the operating panel .............................................................................12

Control knob ........................................................................................................12

PILOT function box (modeling lamp) ...................................................................12

RADIO function box (radio operation)..................................................................13

AUXILIARIES function box (Slave; FC, Audio)....................................................13

Test......................................................................................................................13

Flash readiness ...................................................................................................13

Flash triggering..........................................................................................................14

Automatic Power Drop (APD)....................................................................................14

Maintenance..............................................................................................................15

Replacement of flash tubes .................................................................................15

Regular inspections and repairs................................................................................15

Return to customer service........................................................................................15

Disposal.....................................................................................................................15

Accessories...............................................................................................................15

Cover page.

Contact data..............................................................................................................16

Declaration of conformity...........................................................................................16

Instruction manual PRI

LITE M-PACK 500 / M-PACK 1000 (HS) + PRIO HEAD 1000

PRI

LITE GmbH Wuerzburg - Last revised: 08/2014 - Page 4

Introduction.

Dear photographer,

Thank you for selecting the PRI

LITE power pack and flash head.

As a young, aspiring company, PRI

LITE intends to use innovative technologies and high-

quality products to open up new market segments for professional photography.

Our devices are based on state-of-the-art technology and equipped with carefully selected

components. Our production process is being continuously monitored to ensure high-quality

and safety standards.

Before using this unit, please read the operating manual and safety instructions carefully to

prevent damage to the device and maintain your warranty.

We wish you many successful years of productive and innovative work with our equipment.

Should you have questions about our products, please contact us!

Best regards,

PRI

LITE GmbH

Description.

The PRI

LITE M-PACK 500 und M-PACK 1000 (HotSync) are radio-controlled, battery-

operated power packs with an exchangeable battery which provide one socket for flash

head connection per power pack. The PRIO HEAD 1000 is intended for connection to the

M-PACKs and works with both types of generators (500 and 1000). The power packs’

power output ranges from a minimum level of 16J up to a maximum of 500J and 1000J

covering a range of 6 and 7 f-stops, respectively, which are precisely adjustable in 1/10

increments. The flash recycle time to maximum output is about 2.5 seconds. The flash head

is equipped with an energy-saving LED array as modeling lamp.

The M-Pack HotSync (HS) version is optimized for flash synchronisation up to 1/8000 sec.

Therefore, it provides a long and constant flash duration of 1/200 sec. HotSync function is

only usable in combination with the Priolite Remote Control RC-HS-C/N/P (see instruction

manual) for operation with Canon/Nikon/Pentax cameras, respectively. The M-Pack

HotSync version can also be triggered from other sources, but in this case, the flash sync

time is limited to 1/200 sec.

Delivery of power pack and flash head includes.

◊1 M-PACK 500 or M-PACK 1000 (HS):

◊1 multi-voltage battery charger (M-PACK 500, 16V; M-PACK 1000 (HS), 58V)

◊1 synchronization cable.

◊1 PRIO HEAD 1000:

◊1 flash tube, pluggable, 1 glass dome, 1 black protective cap for transport

◊1 modeling lamp (LED) and 1 tilting head.

For the composition of the kits, please refer to our currently valid price-list.

Instruction manual PRI

LITE M-PACK 500 / M-PACK 1000 (HS) + PRIO HEAD 1000

PRI

LITE GmbH Wuerzburg - Last revised: 08/2014 - Page 5

Intended use.

This power pack is intended for mobile use in professional photography in the studio or on

location. Its purpose is the provision of electrical power for flash generation. The generated

power output is delivered to the flash head. The units must not be used for any other

purpose.

Power packs store energy in capacitors by collecting high voltages, which creates

particular sources of danger. Before using this unit, read and comply the following

safety instructions.

Safety instructions.

◊Flash units may not be operated without supervision.

◊Always use extreme care when handling power packs and flash heads. Damages to

flashtubes should be excluded. A damaged flash tube poses a risk of severe injury

or death, as the voltage-carrying electrodes are exposed and you might come in

contact with them. Therefore, in case of a damaged flash tube the power pack

must be switched off immediately and the flash head disconnected from the

generator. For safety reasons, before exchanging the flash tube you must wait at least

5 minutes after separating the flash head from the switched-off power pack to ensure

that the capacitors have completely discharged via the internal safety circuit. The same

applies to any type of maintenance work or before transports, which may be undertaken

on the units only when they have been switched off/separated and after the waiting

period has expired.

◊Contact with the capacitor voltage is life-threatening; thus, the opening of the casing and

repairs on power packs and flash heads must be carried out only by authorized

customer service personnel.

◊Only the provided original PRI

LITE charger must be used for charging the batteries.

Before each use, check to ensure that the casing as well as all cables, connectors and

sockets are in good, undamaged condition. Otherwise operation of this device is

forbidden; damaged units and/or cables must be repaired or replaced by authorized

customer service personnel.

◊Flash heads must be operated only with a properly mounted glass dome, as flash tubes

can explode due to the development of overpressure.

◊It is particularly important to protect power packs and flash heads from moisture, splash

water, and impacts during use or transport. These units are not designed for operation

in dusty environments. Flash systems must never be used in potentially explosive

areas; to prevent the risk of fire, do not store flammable materials (e.g. decorative

materials, paper, etc.) in the immediate vicinity of the flash units.

◊Do not insert any objects into the ventilation slits or the charging or synchronization

sockets. The ventilation slits must be kept clear during operation.

◊Flash units mounted on pantographs, ceiling systems, or extended stands must be

doubly secured against falling down.

Instruction manual PRI

LITE M-PACK 500 / M-PACK 1000 (HS) + PRIO HEAD 1000

PRI

LITE GmbH Wuerzburg - Last revised: 08/2014 - Page 6

◊Do not flash into eyes from a short distance (under 5 meters) as this can cause injury to

your eyes. Do not look directly into the flash reflector; the flash could be inadvertently

triggered.

◊Ventilate closed rooms regularly to prevent illegal ozone levels, which can be generated

by the use of high-performance flash units.

Specific safety precautions when working with Lithium-ion batteries.

The provided Lithium-ion battery contains a protection circuit that protects the battery

against overload, deep discharge, short circuit and overheating.

In case of improper use (cutting, breaking, overheating) the batteries can explode or cause

fires, even after a prolonged time interval. Therefore, Lithium-ion batteries are generally to

be protected from mechanical damage and kept away from heat, open flames, and

corrosive liquids. Batteries must not be damaged in any way. Lithium cells generally

respond violently with water (particularly in fully charged condition); therefore, in case of

burning do not extinguish the flames with water, but use sand. Damaged Lithium-ion

batteries are readily to be disposed of in appropriate containers.

Lithium-ion batteries contain flammable and / or corrosive solutions and Lithium salts, which

may cause in the case of leakage irritation to skin, eyes, and mucous membranes. In case

of contact with escaped electrolytes, gases, or fire by-products of a Lithium-ion battery, the

following first aid measures must be observed:

Eyes: In case of contact with eyes, rinse immediately for at least 15 minutes with water.

Keep eyelids open in order to ensure the complete flushing of the eye.

Skin: Take off contaminated clothing and rinse under cold water for at least 15 minutes.

Respiratory system: Ensure fresh air supply. If necessary, perform first aid measures.

In any case, following first aid measures a doctor should be consulted.

Lithium-ion batteries must be only recharged with the supplied PRI

LITE charger of the

respective voltage class; use the 16V charger for M-PACK 500 and the 58V charger for M-

PACK 1000 (HS).

The charge should be performed only under supervision and not in close proximity to

combustible materials; sufficient dissipation of heat must be provided (do not charge the

battery in the sun).

If a Lithium-ion battery is carried on air travel, then it must be discharged prior to departure

to avoid any risks.

Instruction manual PRI

LITE M-PACK 500 / M-PACK 1000 (HS) + PRIO HEAD 1000

PRI

LITE GmbH Wuerzburg - Last revised: 08/2014 - Page 7

Technical data M-PACK 500 M-PACK 1000 (HS) .

Output: 500 Ws 1000 Ws

Voltage supply: Lithium-ion battery with protection circuit, no memory effect

16V, 50 Wh 58V, 80 Wh

weight approx. 600 g weight approx. 900 g

Flash recycle time: 2.5 sec. at full power 2.5 sec. at full power

Fastest flash sequence: 3 flashes per second 3 flashes per second

Flash duration t0.5 (sec): 1/4500 at full power 1/4500 (1/200) at full power

f-stop: 64,2 90.2

1m distance,7” reflector,

ISO100, measuring time 1/125

shortest sync time: 1/200 sec. with focal plane shutter cameras

1/800 sec. with central shutter cameras

(M-Pack 1000 HS: 1/8000 sec. using RC-HS-C/N/P)

Sync voltage: 5V for safe flash triggering by modern digital cameras

socket for 3.5 mm phone jack

Flash power control: 1/10 increments in 1/10 increments

over 6 f-stops over 7 f-stops

10 = full power (500 Ws) 10 = full power (1000 Ws)

5 = min power (16 Ws) 4 = min power (16 Ws)

No. of flashes/charge: 220/full power (display ‘10’) 160/full power (display ‘10’)

440/250 Ws (display ‘9’) 320/500 Ws (display ‘9’)

>6000 at low power >6000 at low power

Charger: 16V (multi-voltage) 58V (multi-voltage)

Charging time: approx. 2 hrs to 80% and approx. 3 hrs to full charge

Weight (without tilt): 3,2 kg (battery included) 4,5 kg (battery included)

Dimensions (cm x cm): 40 x 17 46 x 17

Code No.: 04-0500-01 04-1000-02

(M-Pack 1000 HS: 04-1000-03)

Instruction manual PRI

LITE M-PACK 500 / M-PACK 1000 (HS) + PRIO HEAD 1000

PRI

LITE GmbH Wuerzburg - Last revised: 08/2014 - Page 8

Technical data PRIO HEAD 1000 .

Modeling lamp: LED array (equivalent to 80W halogen)

Color temperature (K): 5500

Weight (without tilt): 1,2 kg

Dimensions (cm x cm): 21 x 17

Code No.: 05-1000-01

Initial operation.

Set-up and assembly

For power packs, use the following options for transportation / operation:

1) Standing upright on firm, dry ground with the flash socket on top

2) Clamped to a tripod using a combination of Manfrotto Superclamp and PRI

LITE tilting

head (accessories not included in the standard delivery). The PRI

LITE tilt head is thus

inserted into the rail profiIe of the generator and securely locked using the small lateral

wing screw. The Manfrotto Superclamp mounted on a tripod now takes the stand mount

of the PRI

LITE tilt head. Hereby, the generator serves as a weight loading on the

stand. Depending on the mounting height the power pack can be operated easily from

waist height.

3) The power pack can be stored for transportation purposes in the PRI

LITE gear tube

(accessories not included in the standard delivery) hanging around the shoulder. In the

gear tube, the power pack must only be operated at low power levels to avoid heat

problems.

The flash head is equipped as standard with a tilting head. For set-up on tripods,

pantographs or ceiling systems, this is screwed securely onto the appropriate tripod mount

using the locking thumbscrew on the side of the panner.

If the units are suspended from pantographs, ceiling rails, or extended stands, a

second secure connection is required in accordance with the applicable safety

regulations. It is recommended to insert a steel cable suitable for this purpose (not

included) through the opening of the handle and to secure it to a suitable lug on the

suspension unit.

Adjustment of the tilting head

Dependent on the direction the tilting head is inserted into the rail profile, right and left hand

use is possible. You have the following options for adjusting the flash unit:

◊The inclination angle can be precisely adjusted by means of the large thumbscrew. The

rotation angle (360 °) is set using the tripod mounting screw.

Instruction manual PRI

LITE M-PACK 500 / M-PACK 1000 (HS) + PRIO HEAD 1000

PRI

LITE GmbH Wuerzburg - Last revised: 08/2014 - Page 9

◊

Using the lateral small thumbscrew on the opposite side, the flash unit can be shifted

backwards or forwards in the rail profile; this might be useful for weight compensation

(e.g., when attaching heavy accessories).

To prevent the unit from sliding off the rail and dropping down, the provided M6

screw is to be inserted into the provided thread hole on the rear end of the rail.

Attachment and removal of the glass dome before operating flash heads

The glass dome must be attached or removed only when the flash head unit is

disconnected from the power pack which had been switched-off before. Always

ensure that the flash tube and modeling lamp remain intact and undamaged!

The protective glass dome is fixed to the four pre-mounted springs. The best procedure for

mounting and dismounting is to place the flash unit vertically on a solid surface. Then put

the glass dome carefully over the flash tube, and push it down firmly with gentle pressure

until the glass dome snaps audibly into the springs. For dismounting hold the glass dome

firmly with both hands. Then tilt it slightly so that it disengages from the mounting springs

and pull the glass dome straight off.

Mounting of accessories to flash heads

Light modifiers (reflector, soft box, umbrella, etc.) are to be mounted to flash heads before

the units are put into operation. Accordingly, the power pack must always be switched off

and the flash head disconnected from the power pack before the light modifier is changed.

After longer periods of operation the flash head and the attached accessories

(particularly reflectors) can become very hot. To avoid burns upon contact, you

should use suitable heat guards when handling the equipment or wait until it has

cooled down. Due to the heat build-up, power pack and flash head must not be

operated in the vicinity of flammable objects. Sufficient safety clearance with regard

to decoration for photographic purposes must be ensured.

Connection of reflectors to flash heads

To attach reflectors the clamps are put into open position by pressing the reflector lever

against the spring force until it hits the stop and keep it there. Now place the accessory

evenly and flush to the unit (for accessories with Bowens S-type adapter, place the three

flanges of the accessory that they fit into the corresponding recesses). Do not tilt the

accessory during this process. Then return the lever to its initial position moving with the

spring force to lock the accessory into place. To remove the accessory, hold it firmly

(caution - it could be very hot!), press the lever against the spring force to unlock it and

remove the accessory.

Instruction manual PRI

LITE M-PACK 500 / M-PACK 1000 (HS) + PRIO HEAD 1000

PRI

LITE GmbH Wuerzburg - Last revised: 08/2014 - Page 10

The system is generally compatible with most reflectors of the Bowens / S-Line as well as

HENSEL / E and EH series. As for HENSEL reflectors, the clamps fit around the raised

edge of the reflector from the outside. Should you have any questions concerning

compatibility, please contact us.

Connection of softboxes to flash heads

The PRI

LITE softboxes have a speedring which is mounted to the reflector locking

mechanism of the flash head the same way as reflectors (see description above). For

softboxes of other brands adapters are available upon request. Please ask for details.

Umbrella attachment to flash heads

To attach an umbrella to the flash head insert the rod in the round opening at the front of

the rail profile to the desired length and tighten it using the knurled screw.

Acclimatization

If the flash units are to be set up at a new location with a different humidity level and/or

temperature, the units should stand for a while before operation in the room in which it is to

be used. This should prevent the formation of leakage current which can develop due to

precipitation.

Overheating

All units are equipped with a fan to prevent damage to the flash tube and the unit itself

during long series of flashes. Nonetheless, should overheating occur, an error message will

appear on the LED display. The error message will be automatically reset as soon as the

unit has cooled down.

Starting up

The flash head does not have a main switch. Before starting-up, the flash head cable has to

be connected to the generator by connecting the plug into the socket of the power pack.

This is done by clockwise turning the plug into the bayonet lock. After switching-on the

power pack, the flash head is ready to flash.

Before each operation, the black plastic transportation cap has to be removed.

Each power pack provides only one socket for flash head connection. Only

operation of one PRIO HEAD 1000 per generator is approved. The flash head is

suitable for both types of power packs (M-PACK 500 and M-PACK 1000 (HS)).

The power pack is switched on and off by pressing the main switch protected by a flap

against unintentional switching.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Priolite Accessoires pour appareils photo

Priolite

Priolite MB500 Manuel utilisateur

Priolite

Priolite Octaform Premium 90 Manuel utilisateur

Manuels Accessoires pour appareils photo populaires d'autres marques

Viltrox

Viltrox EF-NEX Instructions d'installation

Calumet

Calumet 7100 Series CK7114 Manuel utilisateur

Ropox

Ropox 4Single Series Manuel utilisateur

Cambo

Cambo Wide DS Digital Series Mode d'emploi

Samsung

Samsung SHG-120 Manuel utilisateur

Ryobi

Ryobi BPL-1820 Manuel d'utilisation

Aegis

Aegis ABL-36020P Manuel utilisateur

Pentax

Pentax Data Back Fc Manuel utilisateur

Fantasea

Fantasea EyeGrabber F Series Manuel utilisateur

Honeywell

Honeywell HDZ20HD Manuel utilisateur

EGO

EGO BA1400T Manuel utilisateur

Sima

Sima SRW-62 Manuel utilisateur

Shape

Shape A7SSMKIT Manuel utilisateur

Slide Kamera

Slide Kamera HST-2 Manuel utilisateur

Power works

Power works 2902613 Manuel utilisateur

SES

SES SE-2047-2 Manuel utilisateur

Olympus

Olympus PT-EP05L Manuel utilisateur

Starlite

Starlite OctoDome nxt Manuel utilisateur