Printek Mt3 Series Manuel

Important:

1. You must charge the battery for 24 hours prior to the first use.

2. Maximum battery capacity is reached after completing a minimum of (3)

normal usage charge and discharge cycles.

3. Always use Genuine Printek Paper to ensure optimal performance.

4. To load paper, pull on the Paper Door Handle to open the Paper Door.

Drop in paper roll as shown in diagram. Close Paper Door.

5. To load battery, slide Battery Door Releases down, and then open the

Battery Door. Insert the Battery as shown in diagram. Close the

Battery Door, and then slide the Battery Door Releases back to the

locked position.

6. To unload battery, slide the Battery Door Releases down, and open

the Battery Door only half way. At this point the battery can be removed.

7. To perform the self test, press and hold the PAPER FEED button, and

then press the ON button.

8. Note: For additional detailed information, please refer to the Operator’s

Manual. A copy of this manual can be downloaded by visiting

www.printek.com

BATTERY DOOR

ON/OFF BUTTON

PAPER FEED BUTTON

POWER ADAPTER INPUT

PAPER DOOR HANDLE

PAPER DOOR

SMART CARD READER

(OPTIONAL)

BATTERY

P/N 91244

P/N 91245 (5-pack)

P/N 91246 (20-pack)

BATTERY DOOR RELEASE

IrDA WINDOW

PAPER ROLL

P/N 91253 (5-pack)

P/N 91254 (35-pack)

P/N 91255 (Case of 200 rolls)

MAG CARD READER

(OPTIONAL)

POWER ON INDICATOR

(GREEN)

BATTERY CHARGING INDICATOR

(AMBER)

ERROR INDICATOR (RED) /

MCR READY INDICATOR (GREEN)

Printek Mt3/Mt3B Quick Setup Instructions

P/N #5688 Rev A

Printek Mt3/Mt3B Quick Setup Instructions cont.

Dip Switch Settings

Dip

Switch

Function Switch # Switch #

1Communication Interface SW1

RS232 Off

IrDA On

2 & 3 Baud Rate SW2 SW3

38,400 Off Off

19,200 Off On

9,600 On Off

2,400 On On

4 & 5 Parity bit SW4 SW5

No Parity Off Off

Odd Parity On Off

Even Parity On On

6Hardware Reset SW6

Enable Reset On

Disable Reset (default) Off

7Not Used SW7

8Printer Power Control SW8

Continuous Power On On

Auto Power Off Off

Please note:

Make certain the printer power is off before changing the dip

switch settings. New settings are only recognized during a

power up sequence.

SERIAL INTERFACE

Switch #1 is shown in the ON position for IrDA.

(Default setting for Mt3 from the factory)

Switch #3, and #4 are shown in the ON position for Bluetooth.

(Default setting for Mt3B from the factory)

Ph: (800) 368-4636

Fax: (269) 925-8539

Web: www.printek.com

E-mail: [email protected]

Innovative Business Printing Solutions

Autres manuels pour Mt3 Series

Ce manuel convient aux modèles suivants

Autres manuels Printek Imprimante

Printek

Printek FormsPro 4600 Manuel utilisateur

Printek

Printek FormsMaster 8003se Series Manuel utilisateur

Printek

Printek FormsPro 4300 Manuel utilisateur

Printek

Printek Mt3-II Series Manuel utilisateur

Printek

Printek FieldPro 541 Manuel utilisateur

Printek

Printek FieldPro RT43 Series Manuel utilisateur

Printek

Printek PrintMaster 852si Manuel

Printek

Printek FormsPro 4000se Series Manuel utilisateur

Printek

Printek FormsPro 4600 Manuel utilisateur

Printek

Printek Mt3-II Series Manuel utilisateur

Printek

Printek FormsMaster 8000 Manuel utilisateur

Printek

Printek MtP Series Manuel d'utilisation et d'entretien

Printek

Printek FormsMaster 8000 Manuel d'utilisation et d'entretien

Printek

Printek I80 Manuel utilisateur

Printek

Printek FieldPro DP-581 Manuel utilisateur

Printek

Printek 850 Series Manuel utilisateur

Printek

Printek FieldPro 641 Manuel utilisateur

Printek

Printek Mt2 Manuel utilisateur

Printek

Printek PrintMaster 862 Manuel utilisateur

Printek

Printek FormsMaster 8000se Series Manuel d'utilisation et d'entretien

Printek

Printek FormsPro 5000 Series Manuel

Printek

Printek PrintMaster 700 Series Manuel utilisateur

Printek

Printek Interceptor 800 Series Manuel utilisateur

Printek

Printek Mt3 Series Manuel utilisateur

Manuels Imprimante populaires d'autres marques

Lexmark

Lexmark 1400 Series Manuel

Canon

Canon i70 Series Manuel utilisateur

Evolis

Evolis Elypso Manuel utilisateur

Kyocera

Kyocera FS-9530DN Manuel utilisateur

Canon

Canon LASER SHOT LBP-1210 Manuel utilisateur

Samsung

Samsung BIXOLON SRP-350plusF Manuel utilisateur

Canon

Canon PIXMA PRO-1 Series Manuel utilisateur

Canon

Canon PIXMA G3560 Guide de configuration

Dell

Dell Color Laser Printer 2130cn Manuel utilisateur

Tektronix

Tektronix Phaser 840 Manuel utilisateur

Epson

Epson ET-7750 Mode d'emploi

Canon

Canon CLBR 460ps Manuel utilisateur

Eltron

Eltron P210 Guide Manuel utilisateur

Ricoh

Ricoh MD-P1 Manuel utilisateur

Epson

Epson SC-F7100 series Manuel utilisateur

Epson

Epson Stylus C40UX Manuel utilisateur

Canon

Canon imagePASS-A2 Manuel utilisateur

Canon

Canon S820D Manuel utilisateur