Supplied By www.heating spares.co Tel. 0161 620 6677
CE
SAFETY, PERFORMANCE &QUALITY
Prima F boilers have been assessed
by
a Government appointed Notified Body and
shown
to
meet the
'Essential Requirements'
of
the European
Gas
Appliance Directive.
The Directive lays
down
requirements for the safety and efficiency of the appliance, togetherwith its design,
construction, and use of materials. It also requires
the
production process to
be
covered
by
an approved
and monitored system of quality assurance.
The BSI kitemark remains
on
the product. demonstrating continued conformity with
the
relevant BSI safety,
performance andquality (BS.5750) standards.
POTTERTON
PRIMA
30F G.C.
No.
41.607.01
POTTERTON
PRIMA
40F
G.C.
No.
41.607.02
POTTERTON
PRIMA
SOF
G.C.
No.
41.607.03
General
Optional Extras
Accessories
Installation Data
CONTENTS
Boiler Dimensions
Site Requirements
Technical Data
Installation Instructions
Commissioning
Health and Safety Information
Control Systems, Pipework and
Wiring Guide
User's Instructions
Page No. 2
Page No. 2
Page No. 3
Page No. 3
Page No. 3
Page No. 3
Page No. 6
Page No. 11
Page No.
18
Back Page
Supplied in
Literature Pack
POTTERTON
PRIMA
60F
G.C.
No.
41.607.04
POTTERTON
PRIMA
80F
G.C.
No.
41.607.32
POTTERTON
PRIMA
100F
G.C.
No.
41.607.33
IMPORTANT
The appliance
must
be
installed
and
serviced
by
a
competent
person
as
stated
in
the
Gas
Safety
(Installation and Use) Regulations 1984.
Prima F boilers (formerly
known
as 'Profile Prima')
are certified
by
BSI
for
safety. it is therefore important
that no external control devices (e.g. flue dampers,
economisers,
etc.)
be
directly
connected
to
these
appliances
unless
covered
by
these
installation
instructions
or
otherwise
recommended
in
writing.
Any
direct
connection
of
a
control
device
not
approved
by
Potterton
could
invalidate
the
BSI
certificate and
the
normal warranty.
GENERAL
Prima F boilers are fully automatically controlled, wall
mounted.
fan
powered,
balanced
flue
appliances,
using a cast iron heat exchanger and are available in
six
outputs
ranging
from
5.86-29.3
kW
(20,000-
100,000 Btulh).
The boilers which are designed
to
provide domestic
hot
water
and/or
central
heating
must
be
used
on
INDIRECT FULLy PUMPED systems only, which may
be sealed
or
open vented.
The boilers can
be
supplied with either of the following
types of flue system:
Standard
horizontal
flue
system
which
is
suitable
for a wall thickness of 100mm{4in) to 510 (20in).
PRIMA 100F MODELONLY
1
metre
horizontal
flue
system
which
provides
a
maximum flue lengthof955mm (37in).
Vertical
Flue
system
which allows
the
flue
to
pass
through a flat roof and terminate at a maximum height
of980mm (38in) measured from the top
of
boilercase.
PRIMA 30F, 40F, 50F, 60F & 80F Modelsonly
2
metre
horizontal
flue
system
which
provides
a
maximum flue length
of
1955mm(77in).
Vertical
flue
system
which allows
the
flue
to
pass
through a flat roof and terminate
at
a maximum height
of 1980mm(78in) measuredfromthetopof boilercase.
OPTIONAL EXTRAS
The following are kits available as optional
extras:-
lnternal Fitment Kit, which is suitable for a maximum
wall thickness of 510mm (20 in.) is
to
be used where
access
to
the outside wall is impracticable.
Pump
Cover
Kits
located
on
top
of
the
boiler
and
designed
to
conceal the pump, and/or any motorised
valves installed above the boiler.
(Note:
Pump cannot
be fitted above
the
boiler
if
the
vertical
flue
kit
is
used).
Terminal
wan
Plate, where necessary can
be
fitted
to the outside wall face to improve the appearance.
after making good around the terminal. 2
Terminal
Guard,
to
be
used
when
the
terminal
is
fitted less
than
2m
above a balcony, above ground
or
above a flat roof
to
which people have access.
45°
and
90°
Flue
Bend
Kits,
giving greater flueing
flexibility (Prima
30F
to 60F only).
Vertex
Flue
Kit,
giving
greater
vertical
flueing
flexibility
through
a roof
space
(Prima
30F
to
60F
only).
Full fitting instructions are provided with each kit.
SEE PAGE
10
FOR PART Nos. OF FLUE KITS AND
OPTIONS.
