Prexiso PR500HV Mode d’emploi

IMPORTANT:

Read before Using EN

PR500HV

SELF-LEVELING ROTARY LASER

www.prexiso-eu.com

WARRANTY

LIMITED

YEARS

IMPORTANT SAFETY INSTRUCTIONS

Do not use the product before you have studied the Safety instructions and the

User Manual on the enclosed CD or on our Homepage.

If you have no such manual, or it is in the wrong language, please ask your agency

for an appropriate copy.

The product is permitted to use for skilled persons only.

WARNING:

•

It is a Class 2 laser product in accordance with IEC 60825-1:2014

•

The following labels are on your laser tool for your convenience and safety.

•

Do not stare into the laser beam or direct it towards other people unnecessarily.

•

Don't dazzle other individuals. Pay particular attention to the direction of the

laser beam when remotely operating the product via an app or software.

A measurement could be triggered at any time.

•

Looking directly into the beam with optical aids can be hazardous.

•

Do not operate the product in explosion hazardous areas or in aggressive

environments.

•

Only use chargers recommended by the manufacturer to charge the batteries.

•

Keep extremities in a safe distance from the moving parts.

•

Watch out for erroneous measurements if the product is defective or if it has been

dropped or has been misused or modified.

•

Carry out periodic test measurements.

Particularly before, during and after important measurements.

•

The product and batteries must not be disposed of with household waste.

LASER RADIATION!

Do not stare into beam

Class 2 laser

< 1mW 630-650nm

IEC 60825-1:2014

WARNING!

The goggles do not protect your eyes against the laser beam.

They are only used to increase the visibility of the laser.

Goggles:

PRODUCT OVERVIEW

PARTS DESCRIPTION

Alignment Sight

Vertical Up Beam Window

Rotary Laser / Glass Enclosed

Keypad

Charging

Power Adapter Plug Jack

Vertical support dot

PARTS DESCRIPTION

5/8" insert

Vertical Down Beam

Mains unit/charger

Plug(EU, China)

Plug(US, Japan, China)

Plug(Australia)

Plug(UK)

KEYPAD AND LED

On/Off Tilt warning on/off

Scan mode

/Speed Slope

Down Left Right

LEDs

POWER-LED

MAN-LED

•

Blinking Green: Laser Tool is Auto-Leveling In

Calibration and / or Default Tilt Warning Set Up

•

Solid Green: Auto-Leveling Complete

•

Blinking Red: Low Battery

•

Solid Red: Battery Needs Recharging

•

Solid Red With POWER-LED – Solid Green:

Manual Mode On (Auto-Leveling Off)

•

Blinking Red With POWER-LED – Blinking

Green: Out of Compensation Range

•

Solid Green: Tilt Warning On

•

Solid Red: Tilt Warning Alarm

•

Solid Green: X Axis Adjust Slope Mode

•

Blinking Green:

X Axis at Maximum Allowed Slope in Slope Mode

X Axis Adjust Calibration Mode

•

Solid Red: Y Axis Adjust Slope Mode

•

Blinking Red:

Y Axis at Maximum Allowed Slope in Slope Mode

Y Axis Adjust Calibration Mode

TILT

Y/Z

RC300 REMOTE CONTROL

RC300

1. Light indicator

2. Speed switch button(Press this button to switch the laser

beam rotating speed from 300rpm->600rpm->0rpm->300rpm).

3. Laser dot moving button (Press this button to clockwise

move the laser dot).

4. Speed switch button(Press this button to switch the laser

beam rotating speed from 300rmp->0rpm->600rpm->300rpm.

5. Slope

6. Laser dot moving button (Press this button to anticlockwise

move the laser dot).

7. Scan mode/Speed

8. Battery lid (Open the battery lid and insert

2 x1.5V AA batteries into the battery compartment).

BATTERIES AND POWER

WARNING:

•

Use charging / power adapter only with Li-Ion battery pack supplied.

Charging any other type of battery may result in damage and/or personal harm.

•

The battery and charging / power adapter can be damaged if damp.

Always store and charge the tool in a dry and covered place.

NOTE:

•

For best battery life, it is recommended to charge the battery once it has been fully

discharged and avoid letting charge for >10 hours at a time.

Operating with Charging / Power Adaptor

•

Laser tool can operate while plugged into charging / power adapter.

Functions and controls of laser tool are the same as when not plugged into

charging / power adapter.

WARNING:

•

Pay close attention to the battery

holder’s (+) and (-) markings for

proper battery insertion. Batteries

must be of same type and

capacity. Do not use a combination

of batteries with different

capacities remaining.

Battery Installation / Removal

Li-Ion Battery version

Alkaline Batteries version

SET UP

OPERATION

Operation in Auto Mode

•

Press to turn on the instrument.

•

Green LED is blinking green when the instrument start to leveling.

TILT LED is off (TILT Function is not on by default), the laser is glitter.

•

After leveling, the laser dot starts to rotate(the default speed is 300rpm),laser

is kept bright, Green LED and TILT LED are solid green.

•

The instrument will be warning when it is tilted, and rotating will be stopped, the

laser will be glitter, TILT LED is solid red. Press to reset.

•

Press to turn off the instrument.

Horizontal Position

•

Place laser tool down on its bottom.

Be sure surface is near level.

•

Press to power ON.

At Angle

•

Press to power ON. Press and hold to turn ON Mnual Mode. Laser tool can now

be positioned to various angles with auto-leveling mode OFF.

NOTE:

To change between horizontal and vertical positions the laser tool must be powered

OFF, repositioned, and then powered ON in the new position.

Vertical Position

•

Place laser tool down on its side,

handle facing up. Be sure surface

is near level.

•

Press to power ON.

Operation in Manual Mode

•

Press and hold for 3 seconds to turn on Manual Mode when the instrument is

in Auto Mode or TILT Mode.

Green LED is solid green, and Red LED is solid red.

•

The Auto-leveling function is off, the instrument can place at any less

than 50°angle.

•

Press and hold for 3 seconds in Manual Mode to turn off Manual Mode, the

instrument will back to Auto-leveling Mode.

Speed Switch/Spot Mode

•

After Powered on and Auto-leveling or in Manual Mode (Not in SLOPE function),

the default speed is 300rpm:

(1) Short press to switch speed, followed by looping from

300rpm->600rpm->0rpm->150rpm ->300rpm;

(2) Short press to switch speed, followed by looping from

300rpm->150rpm->0rpm->600rpm->300rpm.

•

At 0rpm or Scan Mode(Not in SLOPE function):

(1) Press the laser dot will anticlockwise motion;

(2) Press the laser dot will clockwise motion;

At 0rpm:

(1) Short press / the rotation angle of laser dot is 10°.

(2) Long press / the laser dot will rotate at 0.5-1rpm.

(3) Press and hold / ＞4 seconds, the laser will blinking

3 times to remind the laser start to speed up, after that the laser

will rotate at 7.5-10rpm.

(4) Release / the laser dot will back to 0rpm.

•

In Scan Mode:

(1) Short press / the scan angle will rotate 6°, the scan function is kept.

(2) Long press / the scan will be stopped, the laser dot willrotate at

0.5-1rpm.

(3) Press and hold / ＞4 seconds, the laser will blinking 3 times to remind

the laser start to speed up, after that the laser will rotate at 7.5-10rpm.

(4) Release / it will back to scan function.

Remark:

When the rotation speed is switched from 300rpm to 0rpm for 0.5 seconds,

the output power of instrument will be low power, switched from 0rpm to scan

function or rotation for 1 second, it will be high power.

Scan Mode

•

Turn on the Scan Mode:

(1) Short press to turn on scan function, the default angle is 15°

(2) Short press again to turn off scan function.

•

Scan angle switch:

(1) Short press to switch the scan angle, followed by loop from

15°->30°->60°->15°.

(2) Short press to switch the scan angle, followed by loop from

15°->60°->30°->15°.

TILT function

TILT Operation and Reset

•

Press to turn on the instrument;

LED is blinking green when the instrument start to leveling.

Short press , the TILT LED will be solid green, the laser is glitter.

•

After Auto-leveling, the laser starts to rotate.

•

After Auto-leveling, if the instrument is tilted, it will be warning, the rotation will be

stopped, and the laser is kept bright. TILT LED is solid red.

•

Press again, the instrument will reset and enter TILT function again, and

re-leveling.

TILT Mode switch

•

Press to switch to Auto-leveling Mode in TILT Mode, TILT LED will be off.

Remark:

When the instrument is in Manual Mode, it can not switch to TILT

function; If necessary, please resume to Auto Mode.

Operation in Slope function

Horizontal Slope function:

•

First to turn on the Manual Mode after the instrument is powered on.

The is solid green, and the is solid red.

Short press to enter the slope function, the LED is solid green ,

it indicates the instrument is in X axis manual slope function.

Remark:

(In TILT Mode also need to enter the Manual Mode first, then press to enter the

slope mode).

•

/ can control the laser tilt along the X axis.

Press the laser will raise at +X direction of the instrument.

Press the laser will lower at +X direct of the instrument.

*A single short press the laser will tile 20".

*Press and hold / ＞1 second, the laser will tile 15'/second.

*Press and hold / ＞4 seconds, the laser will tile 1°/second.

•

The will blinking green when the tile is over run. Release / , the

will be solid green.

•

Press to switch to Y axis manual slope functuon, the is solid red.

•

/ can control the laser tilt along the Y axis.

Press the laser will raise at +Y direction of the instrument.

Press the laser will lower at +Y direct of the instrument.

(The key-hold time and adjustment amount are same as X axis.)

•

The will blinking green when the tile is overrun.

Release / , the will be solid green.

•

Short press to quit slope function, and back to Manual Mode.

The is off, is solid green and is solid red;

The horizontal slope function can only be entered in Manual Mode,

it will resume to Manual Mode when quit the slope function.

Vertical Slope function:

•

When powered on in vertical state, enter the Auto-leveling Mode, the

is blinking green, and the instrument starts to leveling.

Short press to enter the vertical slope function(Z axis is Autoleveling),

the is solid red.

(In vertical TILT Mode also can enter Slope Mode, TILT and Slope

function can exist concurrently)

•

The operation of vertical slope function is the same as horizontal slope function.

•

Short press to quit slope function, and resume to Auto Mode.

Table des matières

Autres manuels Prexiso Instrument de mesure

Prexiso

Prexiso PXX-400 Manuel utilisateur

Prexiso

Prexiso P60L Manuel utilisateur

Prexiso

Prexiso P30M Manuel utilisateur

Prexiso

Prexiso PTX-99 Manuel utilisateur

Prexiso

Prexiso G5 Series Manuel utilisateur

Prexiso

Prexiso PLT40LI Manuel utilisateur

Prexiso

Prexiso iC4 Manuel utilisateur

Prexiso

Prexiso P15M-3LI Manuel utilisateur

Prexiso

Prexiso PR500HVG Manuel utilisateur

Prexiso

Prexiso P70DLI Manuel utilisateur

Prexiso

Prexiso PMX-42B Manuel utilisateur

Prexiso

Prexiso XL2 Manuel utilisateur

Prexiso

Prexiso P40T Manuel utilisateur

Prexiso

Prexiso P40A Manuel utilisateur

Prexiso

Prexiso P20 Manuel utilisateur

Prexiso

Prexiso PMX-42A Manuel utilisateur

Prexiso

Prexiso P15 Manuel utilisateur

Prexiso

Prexiso P20LI Manuel utilisateur

Prexiso

Prexiso T.O.2 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur