PRESYS Instruments T-30NIR-H
Page 4
2 - T-30NIR-H Calibrator Operation
The T-30NIR-H controls the temperature of the blackbody target and is suitable
for calibration of infrared thermometer.
The calibrator has 3 operating modes:
•Manual Mode to select the block temperature straight from the keypad.
•Programmable Mode: 6 different programs with 11 temperature set point values. The
block temperature is selected among the programmed values by the keys and.
The Programmable Mode with Timer scans automatically the temperature set points.
•Automatic Mode the calibration is performed in an automatic way by the calibrator: the
schedule and the calibration results, besides the object under calibration readings are
stored in the calibrator memory. For pyrometers with local indication, readings are
entered manually and for pyrometers with response in mA, V or thermocouple signal,
reading is performed automatically by the input of the calibrator.
When powered on (ON/OFF key), the calibrator goes through a self-test routine
and shows the last calibration date and the value of the battery voltage. After the self-
test is completed, the display shows the starting menu.
The initial set point is 25.00 ºC:
Through the keys,,and , choose the menu options and press
ENTER.
IN: selection of the calibrator signal input. Choose between Ohms and RTD or
none. More details in item 2.1 –IN Menu.
EXEC: The calibrator enters the manual or programmable operating mode.
CONF: Accesses the calibrator configuration options. More details in item 2.2 –
CONF Menu.
CAL: This option accesses the calibrator adjustment functions, protected by
password. More details in section 5 - Calibration.
COM: Accesses the automatic calibration parameters. It is possible to perform a
calibration without a computer or using it (via ISOPLAN software). More details in item
2.5 -Automatic Operating Mode.
rols the temperature of the blackbody target and is suitable
presys
rols the temperature of the blackbody target and is suitable
to select the block temperature straight from the keypad.
presys
to select the block temperature straight from the keypad.
11 temperature set point values. The
presys
11 temperature set point values. The
block temperature is selected among the programmed values by the keys
presys
block temperature is selected among the programmed values by the keys
scans automatically the temperature set points.
presys
scans automatically the temperature set points.
the calibration is performed in an automatic
presys
the calibration is performed in an automatic
way by the calibrator: the
presys
way by the calibrator: the
schedule and the calibration results, besides the object under calibration read
presys
schedule and the calibration results, besides the object under calibration read
tor memory. For pyrometers with local indication, readings are
presys
tor memory. For pyrometers with local indication, readings are
entered manually and for pyrometers with response in mA,
presys
entered manually and for pyrometers with response in mA,
V or thermocouple signal,
presys
V or thermocouple signal,
reading is performed automatically by the input of the calibrator.
presys
reading is performed automatically by the input of the calibrator.
key), the calibrato
presys
key), the calibrato
r goes through a self
presys
r goes through a self
and shows the last calibration date and the value of the
presys
and shows the last calibration date and the value of the
battery voltage. After the
presys
battery voltage. After the
test is completed, the display shows the starting menu.
presys
test is completed, the display shows the starting menu.
The initial set point is 25.00 ºC:
presys
The initial set point is 25.00 ºC:
Through the key
presys
Through the key
, choose the menu options and press
presys
, choose the menu options and press
: selection of the calibrator signal input. Choose between
presys
: selection of the calibrator signal input. Choose between
none. More details in item
presys
none. More details in item
: The calibrator enters the manual or programmable operating mode.
presys
: The calibrator enters the manual or programmable operating mode.
ccesses the calibrator configuration options. More details in item
presys
ccesses the calibrator configuration options. More details in item
: This option accesses the calib
presys
: This option accesses the calib
password. More detai
presys
password. More detai
ls in section
presys
ls in section
: Accesses the automatic calibration param
presys
: Accesses the automatic calibration param
calibration without a computer or using it (via ISOPLAN software). More details in i
presys
calibration without a computer or using it (via ISOPLAN software). More details in i
Automatic Operating Mode
presys
Automatic Operating Mode
