Prestige PE1BZLR Manuel utilisateur
1PE1BZ_PE1BZLR / FLRS Owners rev A.
IMPORTANT NOTE: The operation of the Security and Convenience System as described in this manual is
applicable to most vehicles. However, due to the conguration of some vehicles, some functions AND/OR
SAFETY PRECAUTIONS may not apply. Please see your installing dealer for more information.
Owner’s Guide
For Model:
PE1BZ
PE1BZLR
Flashlogic FLRSBA
RF Upgrade Kit
22018 Voxx Electronics Corporation. All rights reserved.
Table of Contents
Using Your Remote Control .......................................................3
Remote Start Valet Mode............................................................4
Remote Control Programming...................................................4
Replacing Remote Control Batteries ........................................5
3PE1BZ_PE1BZLR / FLRS Owners rev A.
Using Your Remote Control
Door Lock
To lock the vehicle doors press and release the button.
Door Unlock
To unlock the vehicle doors press and release the button 2 times.
Remote Starting Your Vehicle
To activate the remote start, press and hold the button for 3 seconds. The vehicle
will start and run the predetermined time set up during installation (5 to 60 minutes
selectable).
Remote Start Shutdown
Press and hold the button for 3 seconds to turn the vehicle o. Pressing the
vehicle’s brake will also shutdown the remote start.
Entering the Vehicle while it is Running via Remote Vehicle Start
1. Unlock the vehicle’s doors.
2. Enter the vehicle. DO NOT PRESS THE BRAKE PEDAL!
3. Insert the key into the ignition switch and turn to the ON or RUN
position.
4. Press the brake pedal. The remote vehicle starter will disengage and
the vehicle will operate normally.
NOTE: This feature may not be available on all vehicle makes/models. In some
vehicle applications the the remote start will shut down upon entering the vehicle and
the engine will stop running. For these applications it will be necessary to restart the
vehicle normally. Refer to installing dealer for details.
Preheating or Precooling the Vehicle’s interior
Before exiting the vehicle, set the temperature controls to the desired setting and
operation. After the system starts the vehicle, the heater or air conditioner will
activate and heat or cool the vehicle’s interior to your setting.
42018 Voxx Electronics Corporation. All rights reserved.
Remote Start Valet Mode
Enter / Exit Valet mode for systems using an Flashlogic FLRS kit.
1. Cycle ignition ON ve times [5x OFF/ON] rapidly. (complete this step
within 7 seconds)
2. Wait, LED 1 (on the FLRS kit) will turn solid RED for 2 seconds.
3. Turn ignition to OFF position.
4. Valet Mode Programming Procedure completed.
NOTE: In Valet Mode, the Remote starter is not functional. On units with Keyless
Entry, Lock and Unlock will remain functional. To exit valet mode: repeat steps 1 to 4.
Remote Control Programming
1. Cycle the vehicle ignition ON.
2. Press and release the Valet button 3x.
2. Press 1 button of each transmitter you wish to program, the LED’s will
ash to conrm each transmitter.
3. Turn the vehicle ignition OFF.
NOTE: This system has 1 button programming which programs all channels of the
system.
NOTE: The system will hold up to 4 transmitters in memory, programming a 5th
transmitter will erase the oldest transmitter in memory.
5PE1BZ_PE1BZLR / FLRS Owners rev A.
Replacing Remote Control Batteries
1 Button Remote Control - Model 181BP / 181SP
The CR2032 battery inside each remote control should last approximately 1 year under
normal use. When the battery becomes weak you will notice the remote control range
(the distance from the vehicle the remote control will work) deteriorate and the small LED
on the remote control will dim. To replace the remote control batteries:
1. Using a coin, unsnap and disassemble the halves of the remote control.
2. Remove the old battery, observing the +/- symbols on the battery
and replace with new battery.
3. Reassemble the halves of the remote control.
4. Test operation of the remote control.
Voxx Electronics Corporation.
Customer Service 1-800-225-6074
www.VoxxElectronics.com
FCC COMPLIANCE
This device complies with Part 15 of the FCC rules and with RSS-210 of
Industry Canada. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including any interference that
may cause undesired operation.
Warning!
Changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
PATENTED: www.voxxintl.com/company/patents
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Prestige Démarreur à distance
Prestige
Prestige PE1BTWZ Manuel utilisateur
Prestige
Prestige PLATINUM APS-901C Manuel utilisateur
Prestige
Prestige APSRS1Z Manuel utilisateur
Prestige
Prestige APS25Z Manuel d'installation et d'exploitation
Prestige
Prestige Platinum+ APS 687C Manuel utilisateur
Prestige
Prestige PLATINUM APS-901C Manuel utilisateur
Prestige
Prestige PE5B Manuel utilisateur
Prestige
Prestige APS622E Manuel utilisateur
Prestige
Prestige Prestige 128-8115 Manuel utilisateur
Prestige
Prestige Prestige 128-8121 Manuel utilisateur
Prestige
Prestige Prestige 07S3BP Manuel utilisateur
Prestige
Prestige APS48Z Manuel utilisateur
Prestige
Prestige Prestige 07S3BP Mode d'emploi
Prestige
Prestige APS-901 Manuel utilisateur
Prestige
Prestige APS-687TWE Manuel utilisateur
Prestige
Prestige Platinum APS-787 Manuel utilisateur
Prestige
Prestige APS-687E Manuel utilisateur
Prestige
Prestige PE2LEDZ Manuel utilisateur
Prestige
Prestige Prestige APS-900 Manuel utilisateur
Prestige
Prestige APSSECRS Manuel utilisateur
