Prestige APS-122E Manuel utilisateur

128-9345

Page 1 of 8

Page 1

PATENTED: www.voxxintl.com/company/patents

Model APS-122E

3 Button Remote Security

System Owner's Manual

FCC COMPLIANCE

This device complies with Part 15 of the FCC rules and with RSS-210 of Industry

Canada.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including any interference

that may cause undesired operation.

Warning!

Changes or modications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

NOTE: The manufacturer is not responsible for any radio or TV interference caused

by unauthorized modications to this equipment. Such modications could void

the user’s authority to operate the equipment.

Table Of Contents:

Introduction Features and Options Page 2

Arming The System Page 3 - 4

Protection While The System Is Armed Page 4

Disarming The System Page 4 - 5

Intrusion Signals and Tones Page 5

Valet Override, Programming & Safety Control Switch Page 5 - 6

Manually Overriding Your System Page 5 - 6

Eliminating The Arm/Disarm Chirps Page 6

Remote Panic Operation Page 6

Trunk Release / Optional Device Channels Page 6

Replacement Or Additional Transmitters Programming Page 7

Features And Function Settings Page 8

System Functions At A Glance Page 8

128-9345

Page 2 of 8

Page 2

Congratulations!

Your purchase of this state-of-the-art security system expresses a deep

concern for the security of your vehicle, its contents, and passengers. To

fully appreciate the many functions and safeguards incorporated in this

system, please spend a few minutes reading this manual. You may nd

unexpected features that could mean the difference between “protected”

and “fully protected”.

FEATURES:

2 Three Button Programmable Code Hopping RF Transmitters

Three Channel Receiver (capable of accepting 4 transmitters)

Code Learning

Remote Panic in all modes

Protected Valet

7 Function LED - Arm / Disarm / Zones 1, 2, & 3 / Valet / Arming

Intrusion Alert with Memory

 Audible Arm / Disarm / Defective Zone / Tamper Conrmation

Instant Siren Activation

Starter Disable

True Last Door Arming

Defective Zone By - Pass

Active or Passive Arming Selectable

Chirp Select On/Off

6 Tone Multi-Tone Siren

Additional Negative Trigger Input

RF Inhibit with Ignition On

Parking Light Flasher

On-Board Shock Sensor

OPTIONS:

Remote Trunk Release

Remote Keyless Entry

Remote Starter

Remote Power Window Roll Up

128-9345

Page 3 of 8

Page 3

ARMING THE SYSTEM: (ACTIVE)

1. Turn off the engine, exit the vehicle and close and lock all doors, hood

and trunk.

2. Press and release the Lock button on the keychain transmitter. The

siren will "chirp" once, the vehicle's parking lights will ash once, the

doors will lock (optional), and the dash mounted LED will begin to

slowly ash.

WARNING! Excessive pressure on the transmitter buttons will damage the

internal components on the circuit board. All that is required

is a light push to the button.

NOTE: If the siren "chirped" three times when Locked, then one of the

entry points (hood, trunk, doors) has been left opened. Closing the

hood, trunk, or doors will correct the problem and you do not need

to disarm the system to make the correction. If the siren "chirped"

three times, sometime after arming, the exclusive delayed dome

light learn circuit has been programmed and the system detected

a open entry point after the learned delay expired. Again, closing

the hood, trunk, or doors will correct the problem and you do not

need to disarm the system to make the correction.

ARMING THE SYSTEM: (PASSIVE)

1. Turn off the engine, exit the vehicle, close and lock all doors, hood and

trunk.

2. The dash mounted LED will begin to ash rapidly, indicating that the

system is automatically (passive) arming. As an added convenience,

the automatic passive arming will not begin until all doors and trunk lid

are closed, allowing passengers to exit the vehicle at their convenience.

3. In 30 seconds, you will hear a single short "chirp" from the siren and

the vehicle's parking lamps will ash one time, indicating the system is

ARMED. At this time, the dash mounted LED will begin to ash slowly,

providing a visual indication that the system is fully ARMED.

OPTION NOTE: If the optional (not included) power door lock interface

has been installed, the alarm control module can be

programmed to:

128-9345

Page 4 of 8

Page 4

a) Automatically lock the doors during step 3 on the previous page, or

b) Lock the doors only when the transmitter is operated

4. If you wish to arm the system immediately, simply press and release the

ARMING button on the keychain transmitter. The siren will "chirp" once,

the vehicle's parking lamps will ash once, the doors will lock (optional),

and the dash mounted LED will begin to slowly ash.

PROTECTION WHILE THE SYSTEM IS ARMED:

1. Opening any door, hood or trunk will cause the alarm to immediately

sound. The siren will continue to sound for 30 seconds, then stop and

automatically re-arm the vehicle. If the potential thief left a door opened,

the siren will sound for six 30 second cycles, then re-arm and ignore

the opened door.

2. Any strong impact to the vehicle’s glass will cause the alarm to trigger

for the full 30 second alarm cycle,

3. Whenever the system is armed, the dash mounted LED indicator will

slowly ash. This serves as a visual deterrent to the potential thief. The

LED is a very low current bulb and will not cause the vehicle's battery to

drain, even when left unattended for extended periods.

4. Whenever the system is triggered, the vehicle's parking lights will ash for

the 30 second alarm cycle, attracting added visual attention to the vehicle.

5. Whenever the system is armed, the vehicle's starter will be bypassed. If

a thief should choose to ignore the siren, the vehicle can not be started.

DISARMING THE SYSTEM:

1. As you approach the vehicle, press and release the Unlock button on

the keychain transmitter.

2. The siren will "chirp" 2 times and the vehicle's parking lamps will ash

two times.

3a. ACTIVE: The dash mounted LED will turn off, and remain off until the

system is re-armed.

3b. PASSIVE: Never attempt to disarm the system from a distance that

prevents you from opening a door within 30 seconds. Since the system

is programmed for passive arming, it will begin to re-arm until a door

is opened. Opening the door will suspend the passive arming cycle.

128-9345

Page 5 of 8

Page 5

INTRUSION WARNING SIGNALS:

The system will inform you if an intrusion attempt has occurred while you

were away from the vehicle. If an intrusion attempt has occurred, the siren

will "chirp" 4 times when disarming the system.

The vehicle's parking lights will also ash 3 times to indicate an intrusion

has occurred. Enter the vehicle and observe the dash mounted LED for

further information.

1. If the LED is ashing one time... pause...one time... etc., then an intrusion

attempt was made to a light activated entry point, or the shock sensor

was activated.

2. If the LED is ashing two times...pause...two times...etc., then an intru-

sion attempt was made to the hood, trunk, or an optional sensor that

has been connected to zone 2.

3. If the LED is ashing three times...pause...three times...etc., then an

intrusion attempt was made through one of the vehicle's doors.

These intrusion warning indicators are stored in the system's memory and

will only be erased from memory when the ignition key is turned on.

Push Button LED Valet / SYSTEM OVERRIDE Switch:

The "Valet" switch allows you to temporarily bypass all alarm functions,

eliminating the need to hand your transmitter to parking attendants or

garage mechanics. When the system is in valet mode, all alarm functions

are bypassed, however, the remote panic feature and remote door locks

(optional) will remain operational. To use the valet mode:

1. Enter the vehicle and turn the ignition key to the ON position.

2. Press and hold the LED valet push button switch for 5 seconds until the

LED turns on solid. The LED will remain on as long as the system is

in the valet mode.

3. To return to normal operation, with the ignition switch on, press and re-

lease the LED valet push button switch one time. The LED will turn off

indicating the unit has been returned to the normal mode of operation.

In the event you lose your keychain transmitter, or if the transmitter fails to

disarm the system, the valet switch can be used as a system override switch.

Open the car door (the alarm will sound). Turn the ignition key on, and

press and hold the LED valet switch on. The alarm will stop sounding, and

the vehicle can now be started.

128-9345

Page 6 of 8

Page 6

NOTE: Always remember to exit Valet Mode to ensure that the vehicle

remains protected at all times.

ELIMINATING THE ARM / DISARM CHIRPS:

The normal arming and disarming conrmation "chirps" can easily be turned

on and off using the valet push button switch. To do this:

1. Turn the ignition key on, and then off.

2. Within 10 seconds of turning the ignition key off, press and release the

LED valet push button switch three times.

3a. If, before proceeding with step 2, the chirps were on, then you will hear

2 chirps to indicate that the chirps have been turned off.

3b. If, before proceeding with step 2, the chirps were off, then you will hear

1 chirp to indicate that the chirps have been turned on.

NOTE: Whenever the chirps are by-passed, the 3 chirp defect and 4 chirp

intrusion indicator will always operate. This feature will always

warn you if there is a defective sensor during the arming sequence

or if the vehicle had been tampered with in your absence, even if

the normal arming and disarming chirps have been turn off.

REMOTE PANIC OPERATION:

The Lock and Unlock buttons on your keychain transmitter also functions as

a "panic" switch for instant activation of the alarm in emergency situations.

To use the remote panic switch:

1. Press and hold the arming button on the keychain transmitter for 3 sec-

onds or more. The alarm will immediately sound.

2. To stop the alarm, press and release the Trunk/Key button on the key-

chain transmitter. If the button is not pressed, the alarm will automatically

stop after 30 seconds.

TRUNK RELEASE:

This security system has an additional feature that can be wired to a num-

ber of different optional accessories. Some of the more common uses for

this "channel" are:

 Remote Trunk Release - available for any vehicle with factory installed

electronic push button trunk release.

128-9345

Page 7 of 8

Page 7

 Remote Car Starter - available for most automatic transmission, fuel

injected vehicles.

 Remote Window Roll Up - available for most vehicles equipped with

power windows.

TO ACTIVATE THIS OPTIONAL ACCESSORY

Press and hold the Trunk/Key button on the keychain transmitter for ap-

proximately 3 seconds. If the system has been programmed differently by

your installation center, this output may be accessed by pressing buttons

1 and 2 simultaneously for 3 seconds.

NOTE This feature will not operate when the vehicle's ignition key is

turned "ON".

Transmitter Model Name, 3BP Is Also Found On Back Of

Transmitter Case (Battery Use CR2032)

PROGRAMMING NEW OR REPLACEMENT TRANSMITTERS

(BANK 1)

1) Turn the ignition key to the ON position.

2) Press and release the valet/programming switch 3 times (Siren Chirps)

3) Press the Lock Button of each transmitter you want programmed until

you hear a chirp from the horn or siren.

4) Turn the ignition switch to the OFF position.

The above action programs the Lock, Unlock, and Start/Trunk, which are

typical for your systems.

128-9345

Page 8 of 8

Page 8

APS-122E

SYSTEM FUNCTIONS AT A GLANCE

DASH LED INDICATORS

RAPID FLASHING .............................................. PASSIVE ARMING

SLOW FLASHING.............................................. ARMED

OFF .................................................................... DISARMED

ON - SOLID........................................................ VALET MODE

3 FLASH ... PAUSE............................................ INTRUSION ZONE 3

2 FLASH ... PAUSE............................................ INTRUSION ZONE 2

**1 FLASH ... PAUSE ............................................ INTRUSION ZONE 1

SIREN CHIRP INDICATORS

*1 CHIRP..............................................................ARM

*2 CHIRPS ...........................................................DISARM

3 CHIRPS...........................................................ARM / ZONE ACTIVE

4 CHIRPS...........................................................DISARM / INTRUSION

PARKING LAMPS (Optional)

1 FLASH.............................................................ARM

2 FLASH.............................................................DISARM

3 FLASH.............................................................DISARM / INTRUSION

** Where applicable.

*These chirps are optional and may be disengaged.

To purchase replacement transmitters

or to get additional product information go to:

www.prestigecarsecurity.com

Your System Has These Features Activated:

___Starter Cut-out

___Door Lock Interface

___Shock Detector

___Optional Channel 2 Device

Autres manuels pour APS-122E

Table des matières

Autres manuels Prestige Alarme de voiture

Prestige

Prestige APS-922E Manuel utilisateur

Prestige

Prestige 1286459 Manuel utilisateur

Prestige

Prestige APS25Z Manuel utilisateur

Prestige

Prestige Prestige 128-4246A Manuel utilisateur

Prestige

Prestige APS-596E Manuel utilisateur

Prestige

Prestige APS-OE2B Mode d'emploi

Prestige

Prestige APS-25-CL Manuel utilisateur

Prestige

Prestige Prestige Platinum 128-7401A Manuel utilisateur

Prestige

Prestige APS-510E Manuel utilisateur

Prestige

Prestige APS-140 Manuel utilisateur

Prestige

Prestige APS-25E Manuel utilisateur

Prestige

Prestige APS-20B Manuel utilisateur

Prestige

Prestige APS-997C Manuel utilisateur

Prestige

Prestige APS-25HJ Manuel utilisateur

Prestige

Prestige APS-997E Manuel utilisateur

Prestige

Prestige Platinum APS 996 Manuel utilisateur

Prestige

Prestige 1286520 Manuel utilisateur

Prestige

Prestige 1286469 Manuel utilisateur

Prestige

Prestige PE1BZ Manuel utilisateur

Prestige

Prestige Prestige Platinum APS-400 Manuel utilisateur

Prestige

Prestige APS-20B Manuel utilisateur

Prestige

Prestige APS596Z Manuel utilisateur

Prestige

Prestige Prestige Platinum 128-8128 Manuel utilisateur

Prestige

Prestige APS 800a Manuel utilisateur

Manuels Alarme de voiture populaires d'autres marques

Clifford

Clifford 3606X Manuel utilisateur

Ultra Start

Ultra Start 2500M SERIES Manuel utilisateur

Ultra Start

Ultra Start 650 Series Manuel utilisateur

Audiovox

Audiovox Prestige Platinum+ APS-511C Manuel utilisateur

Sparkrite

Sparkrite SRA8 Manuel utilisateur

Viper

Viper 4708V Manuel utilisateur

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Manuel

Falcon

Falcon Predator XL3 Guide de l'utilisateur

Audiovox

Audiovox Auto Security XR91 Mode d'emploi

Clifford

Clifford Sabre II Manuel utilisateur

CrimeStopper

CrimeStopper CS-8717 Guide de démarrage rapide

Ultra Start

Ultra Start 450 SERIES Manuel utilisateur

Scytek electronic

Scytek electronic Vectra X3 Manuel utilisateur

Excalibur

Excalibur AL-1860-EDPB Manuel utilisateur

Clifford

Clifford CYBER 2 Manuel utilisateur

Gemini

Gemini 7057 Manuel utilisateur

FlashLogic

FlashLogic FLRSBA PRESTIGE Manuel utilisateur

Magicar

Magicar FAI-440 Manuel utilisateur