PR Lighting LS 150 Water Manuel utilisateur

LS 150 Water

PR-6810

The user manual contains important information about the safe installation and use of a projector. Please read

and follow these instructions carefullyandkeep themanual in asafe placefor futurereference.

PR LIGHTING LTD.

http://www.pr-lighting.com

INDEX

1.SAFETYANDWARNINGS

2. INSTUCTIONS

●CLEANINGAND MAINTENANCE

●TROUBLESHOOTING

3.APPEARANCE

4.INSTALLATION

●RIGGING

●PLACEAUNITONAFLATSURFACE

●TRANSPORTATION

●POWERCONNECTIONS

●DMXCONTROLCONNECTION

●DMXTERMINATOR

5. SETUPANDCONFIGURATION

●FRONTPANELOPERATION

●DMXSTARTADDRESS

●STAND-ALONEMODE

●MASTER/SLAVEMODE

6.OPERATIONMENU

7. DMXPROTOCOL

8.TECHNICALDATA

9.CIRCUITDIAGRAMANDPCB CONNECTIONS

●CIRCUIT DIAGRAM

●PCBCONNECTIONS

10.COMPONENTORDERCODES

ACCESSORIES

The followingitemsaresuppliedwith theprojectorandplease check:

Name

Quantity

Unit

Remark

clamps

Power cord

XLR connector

Set

maleandfemale

Safetycord

User manual

Transparent Cover+seal+ screws×6

Set

Optional

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change without notice.

Whilst every care is taken in the preparation of the manual we reserve the right to change specifications in the course of product

improvement.Thepublisherscannotbeheldresponsiblefortheaccuracyoftheinformationherein,oranyconsequencearising fromthem.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good

condition beforeinstallationand use.Shouldthere beany damage caused bytransportation, consult yourdealer and donot usethe unit.Any

damagecausedbyimproperusewill notbeassumedby themanufacturerand/ordealer.

Any future technical change in the user manual won’t be with any further notice.

Note: Forthe productsmade by Guangzhou PRlighting Ltd, thewarranty forthe whole product is one year startingfromthe delivery date

butthelightsourceisnotwithinthewarranty.

1. SAFETYANDWARNINGS

NOTE

Before a projector’s installation, power-on,operationandmaintenance,pleasecarefullyread

thesafetyinformationhereinafter!

Thefollowingsafetysignsareusedintheusermanual.

Warning

User

Manual

Electrical

shock

Goggles

Protective

Gloves

Flames

High

Temperature

● When unpacking , check if there is transportation damage before using the projector. Should there be

anydamagecausedbytransportation,consultyourdealeranddonotuseit.

●The manufacture is not responsible for loss caused by the user not following the manual or changing the

projectorashe/shelikes

●Please be noted that the damage caused by changing the projector at will isnotwarranted.

●Do not hesitateto contact the dealer orthemanufacturer if any questionsor advice.

●The unit canbe used indoors and outdoors and for its IPrating .please refer to Technical Data section of this user

manual.

● Useonlyindrylocations.Keepthis unit awayfromrainand moisture, excessive heat, humidityand dust. Donot

allowcontact withwateror anyother liquids.

●It’s forbidden to make the unit with lower protection level directly or indirectly contact water or other liquids.

●The projector should be kept away from high temperature, fire, electrical surge, vibration and strong light while

beingoperated

●The projector is only intended for installation, operation and maintenance by qualified personnel. And the

operationmust strictlyfollowtheproceduresinthe manual

●No repairable parts in theprojectoranddonotopencoversfor maintenancebyyourself.

●Don’t look straightly into the light sources especially for epileptics, otherwise eyes will be burned.

●Do not connect this device to any typeofdimmerpack

●lens and other optical parts shall be replaced immediatelyif they have deformed or been damaged, otherwise the

lightoutputwillbecompromised.

●Before operation, please confirm that all covers(housing) are on and screws tightened. It’s forbidden to use a

projectorwhilecovers(housing)areoff

●Keep the lamp clean and do nottouch itwithbare hands.

●While operating it, wear protective items.

●Any electrical connection must be carried out by a qualified person .

●Before installation, please confirm the voltage supplied matches what is required for the projector

●Each projector must be properlyearthedandinstalled asper related electrical standards.

●Do not use power cord with its insulator damaged and connect the power cord with other cables.

●If the projector is not used or under cleaning,, please hold the plug and unplug it. Do not unplug it forcefully or

bypullingthe power cable.

●All power cords must conform to related safety and regulations

●While beingoperated,theprojectorshouldnotbe underrainsorinhumidity.

●Do not switch on and off the projector constantly in very short intervals, otherwise the light source’s and other

electricalparts’ lifewillbeshortened.

●There are safety cord holes at the bottom of the base of a projector. In view of safety, please run the safety

cordsupplied throughthesafetycordholes for safetysupport.

●Before any installation, maintenance and cleaning work, please ensure the projector is disconnected from

power mains.

●Under normal temperature, the temperature of the housing will be 55℃; after being stable, the unit’s

surface temperaturewillbe70℃

●Whilethe lamp is stricken for the firsttime, there will be smoke and strange smell. It’s normal and does not

meantheprojector hassome defects.

●While operated, do not touch the metallic housing. It is very hot during operation.

●Do not mount the projector directly on inflammable surface.

●Do not project the beam straightly on combustible items and the minimum distance between the projector

and illuminated items is10m.

●A projector should be installed with good ventilation and the minimum distance between the projector and

wallsis50cm.Atthesametime,pleaseensurethefansandair inletsandoutletsareworkable.

2. INSTRUCTIONS

●CLEANINGANDMAINTENANCE

For the units with optical lens, because of the accumulation of the smoke, oil and dust on lens, the light output will be

compromised. For the reliable use of the unit, it is very necessary to keep it clean. The unit is IP65 rating waterproof device.

Unless approval by some professional technician for necessary internal component replacement, it’s forbidden to dismantle the

unit.

Cleaning frequency is to be decided by operations and its environment. Use soft cloth and normal detergent for glass for cleaning

work. It’s advised external optical system be cleaned every 20days. Keep lens clean and do not touch optical parts with bare

hands.

●Beforeanymaintenanceandcleaning,please ensuretheprojectisoffthepower

●Onlyqualified personisallowed todo maintenance

●Duringmaintenance and before maintenance,theprojector mustbe offpower.

●To avoid internal damage, sun light or other light mustn’t penetrate into the projector via front lens whether

itrunsor not

●Do not use alcohol or other organic solvent to clean the housing to avoid damage.

●Do not use any solvent with chemical elements to clean color filters or hot mirror.

●TROUBLESHOOTING

PROBLEM

ACTION

The projector doesn’t switch on

Check thepowercordconnection

Power Switch fails or is not connected well, call a professional

technicianforrepairingand checking

Control board is not connected normally, call a professional technician

forrepairing and checking,

Theprojectcanbe turnedon,butthe LEDlamps

can’t be on

LED lamp board is notconnected well, call a professional technician for

repairingand checking

TheLED lamps canbeon,butnotcontrolled

byDMX

Check ifDMXStartAddressisproperlyset

Check ifXLRcablefails ornot

Thebrightnessdecreasesobviously

Ambient temperature is too hot which makes the projector too hot,

pleasetakeappropriate ventilationmeasures

3. APPEARANCE

4. INSTALLATION

●RIGGING

Take 1 clamp and 1 safety cord out from the package and tighten the clamp with the arm, and then mount the whole uniton the truss,

tighten the clamp’s retainers to keep the unit stable. (See the WARNING onthe underside of the base as shown above) To pass the

SAFETYCORDthroughtheARM forsafety!Alwaysensurethattheunit is firmlyanchoredto avoid vibrationand slippingwhilst

functioning. Always ensure that thestructure that youare goingto mount the unit to is secureand strongenough to supportthe weight

oftheunitLoosenthebigknob and adjust the head’s angle fortheeffectdesired and the tightenit.Theinstallation iscompleted.

(iftheunitiswit wirelesscontrol,whilebeing hung,theantennashouldfacedown)

●PLACEAUNITONAFLATSURFACE

Before placing a unit on a flat surface, loosen the small knob with the support and make the angle between the arm and the support

60degrees.Tightenthesmallknob. Loosenhebigknob and adjustthe anglebetweenthe armandunitasdesiredand thentightenit.

.(Ifthe unitiswith wirelesscontrol,after the unit isplaced on aflat surface the antenna should face up)

Arm

Safety Clamp

Warning

For safety, please

run the safety cord

through the safety cord

hole and ensure it is

tightened .

Body

Arm

●TRANSPORTATION

Beforetransportation, tighten both knobs afterthe arm and support are overlapped.

WARNING:

●TheprojectorMUSTbe lifted orcarriedbytheHANDLESinsteadofclamps.

●.Forsafety the safety cord should afford 10 times the Projector’s weight.

●POWERCONNECTION

Connect the powercordasfollows:

L(live)=brown

E(earth)=yellow/green

N(neutral) =blue

Before power connection, please ensure the power supplied must match what the nameplate says. It is recommended that each

projectorbe connected withpowerseparatelyso that theymaybeindividuallyswitchedonand off.

Note: If projectors are connected in series, please connect POWERIN port of the 1st projector with the Power Mains, then

connectitsPOWEROUTwithPOWERINof the2nd projector,and soontillallfixturesareconnected. Ifthevoltagesupplied

is 200V-240V, the maximum projectors connected is 8pcs, if it is 100V-120V, the maximum is 4pcs. The diameter of the cores

ofthewiresforthePowerin/outcablesmustbeequalor biggerthan2.5mm2.

●Theearth wire(yellow/green) must beconnectedtothe ground. And electrical connection mustbe in

accordance withthe standardsconcerned.

●Ifany questionsabouttheelectricalinstallation,donotcontinue but consult aqualifiedelectrician.

●DMXCONTROLCONNECTION:

Connection between controller and projector and between one projector and another must be made with a twin-screened cable, with

each wire having at least a 0.5mm in diameter. Connection to and fromthe projector is via cannon 5 pin (which are included with the

projector)or 5pinXLRplugsandsockets.The XLR'sareconnectedas shown inthe figure above.

Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. XLR plugs and sockets

mustn’t be connected in any way other than mentioned in the above figure. The unit accepts digital control signals in protocol

DMX512 (1990).

Connect the controller’s DMX output to the first fixture’s DMX input, and connect the first fixture’s DMX output to the second

fixture’s DMX input and connect the rest fixtures in the same way. Eventually connect the last fixture’s DMX output to a DMX

terminatorasshowninthefigurebelow.

●DMXTERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents

electricalnoise fromdisturbingandcorruptingtheDMXcontrol signals.

The DMX terminator is simply an XLR connector with a 120(ohm) resistor connected across pins 2 and 3, which is then plugged

intothe outputsocketonthe lastprojectorinthechain.Theconnectionsare illustratedbelow.

5. SETUPANDCONFIGURATION

●FRONTPANELOPERATION

To browse through or modify the projector’s functions, press key ENTER for more than 3 seconds to unlock the control panel and

enter the menus. To set or browse through the projector’s functions, press key UP or DOWN. Press the key ENTER to enter the

submenusandthe currentparameterswillbedisplayedwhileflashing.Presskey UP or DOWN to change values(plusor minus)

Press key ENTER to save yourchanges and enter into the upperlevelmenuwhile flashingsstop;

Press key FUNC,it willreturntothe upper menu(parameters not saved)or browsethrough 1st levelmenus;

Press key FUNC for 1second ornonekeyis pushed for1minute, the menuwill beescapedandcurrent operationmode displayed.

IfDMXsignal isavailable, LED indicationison. Otherwiseitisoff.

DMX OUT

DMX OUTDMX IN

DMX Controller

DMX Teminator

120

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor

across pins 2 and 3 in an XLR plug

and insert into the DMX out socket

on the last unit in the chain. PIN 3

PIN 2

●DMXSTARTADDRESS

EachProjectormustbegivena DMX startaddressso that the correctprojectorrespondstothecorrect controlsignals.ThisDMXstart

address is the channel number from which the projector starts to “listen” to the digital control information being sent out from the

controller.TheUnit has1 DMXmode.Ithas8channels, so set the No. 1 projector’s address 001, No. 2 projector’s address 009, No.3

projector’s address 017, No. 4 projector’s address025,andsoon.

Launchtheprojector. Pressbutton ENTER morethan2secondsto unlockpanel.

Pressbutton ENTER to displayDMXaddress;

Pressbutton UP and DOWN,youcansetthe address;

Pressbutton ENTER to confirm;after poweredonnext time,the default willbelastvalue saved

Pressbutton FUNC,it willreturntothe upper menu

●STAND-ALONEMODE

Operate the projector without connecting with a controller, enable the master mode through the operation panel, the

projector will run in Stand-Alone mode automatically.

DMX address can be set at any number within 512.

●MASTER/SLAVEMODE

Many projectors can run synchronously in the Master/Slave mode by linking them with each other. First,

connect the first fixture’s DMX output to the second fixture’s DMX input using XLR-XLR control cable and then connect the second

fixture’s DMX output to the third fixture’s DMX input, and so on until all projector are connected in this way. Eventually connect the

last fixture’s DMX output to a DMX terminator. Set 1st projector as the master and others are Slaves.

StartAddressesofall Slaves are 001; Operation mode of the Master can be set any mode for a Master’ and Slaves’ operation mode can

be setaccordingly

After Poweredon, the group willruninMaster/Slave Mode

6. OPERATIONMENU

1stlevelmenu

2ndlevelmenu

3rd levelmenu

4thlevelmenu

Address

001 -512

DMXAddress

ConfigSetup

MasterSlave

Slave

DefaultSlave

Master

LanguageSetup

English

Default：English

Chinese

Slave MasterSlave

DMX OUT

DMX OUTDMX IN

DMX Controller

DMX Teminator

LcdLightSetup

Backlightwillbeoff

3minutesafternone

button ispushed

Off

DisplayInvert

Yes

FactorySetting

Yes

PRMTransmit

Yes

cleanProgra

Yes

Moto offset

Color

Focus

-128-127

Moto Reset

Yes/No

Information

LEDTemperature

FixtureuseTime

XXXX

SoftwareVersion

X.X.X

TestMode

AutoTest

Dimmer

000 -255

LED brightness

Color

000 -255

Motorposition

Wave1

000 -255

Motorposition

Wave2

000 -255

Motorposition

Focus

000 -255

Motorposition

OperationMode

DMX Mode

Yes

User Memory

Yes

UserProgra Edit

（ET01~ET16）

Dimmer

000 -255

Strobe

000 -255

Color

000 -255

Wave1

000 -255

Wave2

000 -255

Focus

000 -255

KeepTime

000 –200(0-20S)

7. DMXPROTOCOL

Channel No.

Function

DMXValue

Description

Dimmer

000-255

Dimmer Fine

000-255

Dimmer in16bit

Strobe

000-007

008-255

Strobespeedfromslowto fast

Colorwheel

000-009

White

8. TECHNICALDATA

ELECTRICSPECIFICATIONS

Inputvoltage:100V~240VAC，50/60Hz

Inputpower:160W @ 230V

Maximumcurrent:AC0.9A

Powerfactor：PF>90%

010-019

White -Magenta

020-029

Magenta

030-039

Magenta–Orange

040-049

Orange

050-059

Orange -Yellow

060-069

Yellow

070-079

Yellow-Blue

080-089

Blue

090-099

Blue–Cyan

100-109

Cyan

110-119

Cyan -White

120-127

White

128-191

Clockwiserotationfromslowtofast

192-255

Anti-clockwise rotationfromslowto fast

WaveWheel1

000-001

002-127

Clockwiserotationfromslowtofast

128-255

Anti-clockwise rotationfromslowto fast

WaveWheel2

000-001

002-127

Clockwiserotationfromslowtofast

128-255

Anti-clockwise rotationfromslowto fast

Focus

000-255

Motorposition

Function

000-199

200-209

Motorreset

210-255

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels PR Lighting Luminaire

PR Lighting

PR Lighting XR440 BWS Manuel utilisateur

PR Lighting

PR Lighting JNR-8154B Manuel utilisateur

PR Lighting

PR Lighting AQUA 350E BWS Manuel utilisateur

PR Lighting

PR Lighting XLED 2007 BEAM PR-8123 Manuel utilisateur

PR Lighting

PR Lighting AQUA LED 1700 FRAMING Manuel utilisateur

PR Lighting

PR Lighting THEATRE COLOUR LT Manuel utilisateur

PR Lighting

PR Lighting XL WASH 1200 PR-2905 Manuel utilisateur

PR Lighting

PR Lighting PR-2735 Manuel utilisateur

PR Lighting

PR Lighting ARC LED 1572 Manuel utilisateur

PR Lighting

PR Lighting XR 1700 Wash Manuel utilisateur

PR Lighting

PR Lighting XR330 BWS Manuel utilisateur

PR Lighting

PR Lighting AQUA MARINE 580 BEAM Manuel utilisateur

PR Lighting

PR Lighting LS 90 Logo Manuel utilisateur

PR Lighting

PR Lighting XRLED 2500-WFraming Manuel utilisateur

PR Lighting

PR Lighting XRLED 700-WBWS Manuel utilisateur

Manuels Luminaire populaires d'autres marques

Emos

Emos CLASSIC ZY1431T Manuel utilisateur

Westinghouse

Westinghouse Outdoor Lighting Fixture Manuel utilisateur

Hedler

Hedler C 12 silent Manuel utilisateur

Blizzard Lighting

Blizzard Lighting Puck: CSI Manuel utilisateur

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manuel utilisateur

Lightmaxx

Lightmaxx Shaft 5R Manuel utilisateur

Triarch

Triarch 31083 Manuel utilisateur

Philips

Philips 32614 Series Manuel utilisateur

IKEA

IKEA TIVED Manuel utilisateur

Lightolier

Lightolier LP200 Manuel utilisateur

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manuel utilisateur

Martin

Martin MAC 250 Krypton Manuel utilisateur

Cooper Lighting

Cooper Lighting Halo L3232E Manuel utilisateur

Stageline

Stageline ODW-2410RGBW Manuel utilisateur

Light Sky

Light Sky Tornado Series Manuel utilisateur

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Manuel utilisateur

Lightolier

Lightolier Lytespan 83ED17S Manuel utilisateur

Lightolier

Lightolier Calculite CS8226 Manuel utilisateur