PR Lighting PR-8541 Manuel utilisateur

1/22

XLED 4022RZ

PR-8541

The user manual contains important information about the safe installation and use of a projector. Please read

and follow these instructions carefully and keep the manual in a safe place for future reference.

PR LIGHTING LTD.

http://www.pr-lighting.com

XLR connector 1 Pc

2/22

INDEX

1. SAFETY AND WARNINGS

2. INSTUCTIONS

3. INSTALLATION

4. SETUPAND CONFIGURATION

5.OPERATION MENU

6. DMX PROTOCOL

7.TECHNICAL DATA

ACCESSORIES

The following items are supplied with the projector and please check:

Name Quantity Unit Remark

Power Cord 1 Pc

Safety cord 1 Pc

User manual 1 Pc

G clamps 2 Pcs

Ωclamps 2 Pcs

Please note that as part of our ongoing commitment to continuous product development, specifications are

subject to change without notice. Whilst every care is taken in the preparation of the manual we reserve the

right to change specifications in the course of product improvement. The publishers cannot be held responsible

for the accuracy of the information herein, or any consequence arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and /

or the unit are in good condition before installation and use. Should there be any damage caused by

transportation, consult your dealer and do not use the unit. Any damage caused by improper use will not be

assumed by the manufacturer and / or dealer.

3/22

1. SAFETY AND WARNINGS

NOTE

Before a projector’s installation, power-on, operation and maintenance, please carefully read

the safety information hereinafter!

The following safety signs are used in the user manual.

Warning

User

Manual

Electrical

shock

Goggles

Protective

Gloves

Flames

High

Temperature

●When unpacking , check if there is transportation damage before using the projector. Should there be any

damage caused by transportation, consult your dealer and do not use it.

●The manufacture is not responsible for loss caused by the user not following the manual or changing the projector

as he/she likes

●Please be noted that the damage caused by changing the projector at will is not warranted.

●Do not hesitate to contact the dealer or the manufacturer if any questions or advice.

●The projector is for indoor use only, IP20.

●Use only in dry locations. Keep this unit away from rain and moisture, excessive heat, humidity and dust. Do not

allow contact with water or any other liquids.

●The projector should be kept away from high temperature, fire, electrical surge, vibration and strong light while

being operated

●The projector is only intended for installation, operation and maintenance by qualified personnel. And the

operation must strictly follow the procedures in the manual

●No repairable parts in the projector and do not open covers for maintenance by yourself.

●Don’t look straightly into the light sources especially for epileptics, otherwise eyes will be burned.

●Do not connect this device to any type of dimmer pack

●After lamp switched on, the minimum distance between the projector and illuminated surface is 10m

●lens and other optical parts shall be replaced immediately if they have deformed or been damaged, otherwise the

light output will be compromised.

●Before operation, please confirm that all covers(housing) are on and screws tightened. It’s forbidden to use a

projector while covers(housing)are off

●Keep the lamp clean and do not touch it with bare hands.

●While operating it, wear protective items.

●Any electrical connection must be carried out by a qualified person .

●Before installation, please confirm the voltage supplied matches what is required for the projector

●Each projector must be properly earthed and installed as per related electrical standards.

●Do not use power cord with its insulator damaged and connect the power cord with other cables.

●If the projector is not used or under cleaning,, please hold the plug and unplug it. Do not unplug it forcefully

or by pulling the power cable.

●All power cords must conform to related safety and regulations

●

While being operated, the projector should not be under rains or in humidity.

●Do not switch on and off the projector constantly in very short intervals, otherwise the light source’s and other

electrical parts’ life will be shortened .

●There are safety cord holes at the bottom of the base of a projector. In view of safety, please run the safety

4/22

cord supplied through the safety cord holes for safety support.

●Before any installation, maintenance and cleaning work, please ensure the projector is disconnected from

power mains.

●After running for 30minutes, the temperature of the housing of the projector is 45℃.After stable operation ,

its temperature is 60℃.

●While the lamp is stricken for the first time, there will be smoke and strange smell. It’s normal and does not

mean the projector has some defects.

●Do not mount the projector directly on inflammable surface.

●Do not project the beam straightly on combustible items and the minimum distance between the

projector and illuminated items is 10m.

●A projector should be installed with good ventilation and the minimum distance between the projector

and walls is 50cm. At the same time, please ensure the fans and air inlets and outlets are workable.

2. INSTRUCTIONS

●CLEANING AND MAINTENANCE

If a projector can’t start. Please check if the fuse is blown up. If it does, replace it with a new fuse with same ratings. And the

projector has over-temperature protective device. If the temperature is too high, the protective device will be triggered to shut the

projector off. When it happens, please check if the fans run normally or fan shield is blocked by dust. After the issue is solved,

restart the projector.

The accumulation of oil, smoke and dust on the lens will compromise the light output. Cleaning a projector is very necessary to

ensure a reliable use of it. Cooling fans need to be cleaned every 15days. Internal lens, reflector and hot mirror need to be cleaned

periodically to optimize light output.

Cleaning frequency is to be decided by operations and its environment. Use soft cloth and normal detergent for glass for cleaning

work. It’s advised external optical system be cleaned every 20days and internal optical systems every 30/60days. Keep lens clean

and do not touch optical parts with bare hands.

●Before any maintenance and cleaning, please ensure the project is off the power

●Only qualified person is allowed to do maintenance

●During maintenance and before maintenance, the projector must be off power.

●To avoid internal damage, sun light or other light mustn’t penetrate into the projector via front lens

whether it runs or not

●Do not use alcohol or other organic solvent to clean the housing to avoid damage.

●Do not use any solvent with chemical elements to clean color filters or hot mirror.

●LUBRICATION

To ensure smooth movement of gobos and zoom and focus lens, it’s advised rotators’ bearings and 2 sliding bars for zoom and

focus lens be lubricated every 2 months. High quality and high temperature lubricant/grease is advised..

●TROUBLESHOOTING

PROBLEM ACTION

The projector doesn’t switch on ¾Check the fuse on the power socket.

¾Check the lamp.

The light source is on but the projector doesn’t

respond to the controller

¾Make sure that the fixture’s start address is right

¾Replace or repair the XLR signal cable.

The projector functions intermittently ¾Make sure the fan is working well or fans and their shields are not blocked

Beam appears dim, Low in brightness ¾Make sure the lamp is within its lifespan

¾Remove dust or grease from the lenses.

The project image appears to have a halo ¾Carefully clean the lamp, optical lenses and other components.

Heavily Defective Beam ¾Check if lens are in good condition(not cracked)

¾Clean dust or grease on the lens.

5/22

3. INSTALLATION

●RIGGING

Before moving a projector, Please lock Pan and Tilt. Before its operation, please unlock them. It’s forbidden to run a

projector with power while it is locked

Take 2 clamps and the safety cord out from the package and mount 2 clamps on the underside of fixture with 2 retainers attached

to each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. (See the WARNING on the

underside of the base as shown above) To pass the SAFETY CORD through the HOLES for safety! Always ensure that the

projector is firmly anchored to avoid vibration and slipping whilst functioning. Always ensure that the structure that you are going

to mount the projector to is secure and strong enough to support the weight of a XR 1000 Framing

●PACKAGING

To avoid damaging or deforming the lens plate before packaging, please follow the instructions below: If the fixture needs to be

packaged, before packaging, it should be powered-on to make the lens plate at the lowest position; the top of the lens plate must not be

higher than the top of the head cover, otherwise, the lens plate will be damaged and malfunction. Please note it!!

Note: Because the LED product consumes high power and the top end of its mixing rod is convex surface being very hot if the

light is on, the mixing rod’s surface must be very clean without any dirt. If it is dirty, please clean it in time, otherwise the dirt on the

surface will absorb much heat, resulting in the mixing rod being burned. Please note it!!

Safety Cord

Damp

Handle

Control Menu

please run the safety cord

through the two holes for

safety.

6/22

WARNING:

●The projector MUST be lifted or carried by the HANDLES instead of clamps.

●.For safety the safety cord should afford 10 times the Projector’s weight.

●POWER CONNECTION

Connect the power cord as follows:

L(live)=brown

E (earth) =yellow/green

N (neutral) =blue

Before power connection, please ensure the power supplied must match what the nameplate says. It is recommended that each

projector be connected with power separately so that they may be individually switched on and off.

Note: If projectors are connected in series, please connect POWERIN port of the 1st projector with the Power Mains, then

connect its POWER OUT with POWER IN of the 2nd projector, and so on till all fixtures are connected. If the voltage supplied

is 200V-240V, the maximum projectors connected is 8pcs, if it is 100V-120V, the maximum is 4pcs. The diameter of the cores

of the wires for the Power in/out cables must be equal or bigger than 2.5mm2 .

●The earth wire(yellow/green) must be connected to the ground. And electrical connection must be in

accordance with the standards concerned.

●If any questions about the electrical installation, do not continue but consult a qualified electrician.

●DMX CONTROL CONNECTION:

The

surface of

black

lighting

pillar

must be

clear and

no dust.

Connection

each wire h

rojector) or

ote: care s

mustn’t be

DMX512 (1

Connect the

fixture’s D

terminator a

●

DMX TE

In the Contr

electrical no

The DMX t

into the outp

4. SET

●

Front Panel

etween contr

ving at least a

5 pin XLR pl

ould be taken

onnected in a

990).

controller’s D

X input and

shown in the

MINATOR

ller mode, at

se from distur

rminator is si

t socket on th

PAND CO

Operation

ller and projec

.5m

in dia

gs and sockets.

to ensure that

y way other t

X ou

ut to

onnect the res

igure b

low.

he last fixture

ing and corrup

y an XLR c

last projector

FIGURATI

120

or and betwee

eter. Connecti

The XLR's ar

one of the pi

an mentioned

the first fixtur

fixtures in th

in the chain, t

ing the DMX

nnector with

n the chain. T

Con

acros

and in

7/22

one projecto

n to and from

connected as

s touch the m

n the above fi

’s DMX inpu

same way. E

e DMX outpu

ontrol signals.

Ω(ohm)

e connections

DMX TERM

CONNE

ect a 120

pins 2 and

ert into the

the last uni

and another

he projector is

hown in the fi

tallic body of t

ure. The proj

, and connect

entually conn

has to be con

esistor connec

re illustrated b

NATOR

TION

(OHM) resi

in an XLR

DMX out so

in the chai

ust be made

via cannon 5

ure above.

e plug or eac

ctor accepts di

the first fixtur

ct the last fix

ected with a

ed across pins

ow:

plug

ket

ith a twin-scre

in (which are i

other. XLR p

ital control si

’s DMX outp

ure’s DMX o

MX terminat

2 and 3, whic

PIN 3

ned cable, wi

cluded with t

ugs and socke

nals in protoc

t to the seco

tput to a DM

r. This pre

is then plugg

8/22

Press ESC button on the left or the sign of Arrow on the bottom right to enter into menu. The ESC button is used to enter into

main menus and exit the current menu. And use UP or DOWN button to select any menu desired and press ENTER button to

confirm.

There 4 LED indications on the control panel, which are red indication for DMX signal, yellow indication for Master fixture,

blue indication for SLAVE fixture and green indication for SOUND control respectively.

The fixtures uses buttons coupled with touch screen to select menus, which makes the interface simple and clear and improves

the operability very well.

Display Menu Functions：

Item Instruction

DMX

DMX Address 1~512 Select

DMX Channel 15ch /28ch /30ch /81ch/104ch

DMX Value

Setting

Pan Inverse On/Off

Tilt Inverse On/Off

Fan Run Mode Auto Mode

Full Speed

Dimmer Curve

Curve1 (/)

Curve2 (S)

Curve3 (J1)

Curve4 (J2)

Smooth Curve On/Off

Show

Show 1

Show 2

Show 3

Show 4

Standby

Test

Auto Show

Manual Test Pan/Tilt/Zoom/Rotation/Dimmer/Strobe/Red/Green/Blue/White

Factory Test

Reset

All Reset On/Off

Pan&Tilt Reset On/Off

Others Reset

(Zoom & Lens Rotation) On/Off

Factory setting YES/NO

Display

Language 中文/English

Blacklight On/Off

Direction Forward

Reserve

Information

Version Current Software Version

Temperature Current Using Temperature

Fan State Normal

Abnromal

Used Time Current Used Time

9/22

5. DMX PROTOCOL

15 Channels

Channel Function DMX Value Description Remark

1 Pan 0-255 0

~5400 horizontal scanning

2 Tilt 0-255 0

~240

vertical scanning

3 Zoom 0-255 4

~60

linear

4 Rotation

0-127 0

~51

128-192 Clockwise

Fast-Slow

193-255 Anti-clockwise

Slow-Fast

5 Dimmer 0-255 0~100% linear

6 Strobe

0-15 Open

16-131 Strobe Slow-Fast

132-139 Open

140-181 Close quickly, then, open slowly

182-189 Open

190-231 Close slowly, then, open quickly

232-239 Open

240-247 Random strobe

248-255 Open

7 Red 0-255 0~100% linear

8 Green 0-255 0~100% linear

9 Blue 0-255 0~100% linear

10 White 0-255 0~100% linear

11 Color Temperature 0 No Change

1-255 10000K~2700K linear change

12 Color Macro

0-3 Normal Control

4-127 Color change 1～32

129-131 Sound Control 0

132-135 Sound Control 1

136-139 Sound Control 2

…… ……

188-191 Sound Control 15

192-195 Auto Mode 0

196-199 Auto Mode 1

200-203 Auto Mode 2

…… ……

252-255 Auto Mode 15

13 Color Macro Speed 0-255 Speed Slow-Fast

14 Reset

100-109 Smooth dimming ON

150-159 Smooth dimming OFF

200-209 Machine reset

15 Dimmer Curve 0 Memory (display default values)

1-63 Curve1 (/)

10/22

64-127 Curve2 (S)

128-191 Curve3 (J1)

192-255 Curve4 (J2)

Notice: Channel 11 Color Temperature must be used together with RGBW

28 Channels

Channel Function DMX Value Description

Remar

1 Pan 0-255 0

~540

horizontal scanning

2 Pan Fine 0-255 0

horizontal scanning fine

3 Tilt 0-255 0

~240

vertical scanning

4 Tilt Fine 0-255 0

vertical scanning fine

5 Zoom 0-255 4

~60

linear

6 Zoom Fine 0-255 0 ~ 1mm fine

7 Rotation

0-127 0

~51

128-192 Clockwise

Fast-Slow

193-255 Anti-clockwise

Slow-Fast

8 Rotation Fine 0-255 0 ~1

fine

9 Pan/Tilt Speed 0-255 Speed Fast-Slow

10 Reset

100-109 Smooth dimming ON

150-159 Smooth dimming OFF

200-209 Machine reset

11 Dimmer 0-255 0~100% Linear

12 Strobe

0-15 Open

16-131 Strobe Slow-Fast

132-139 Open

140-181 Close quickly, then, open slowly

182-189 Open

190-231 Close slowly, then, open quickly

232-239 Open

240-247 Random strobe

248-255 Open

13 Red 1 0-255 0~100% linear

14 Green 1 0-255 0~100% linear

15 Blue 1 0-255 0~100% linear

16 White 1 0-255 0~100% linear

17 Red 2 0-255 0~100% linear

18 Green 2 0-255 0~100% linear

19 Blue 2 0-255 0~100% linear

20 White 2 0-255 0~100% linear

21 Red 3 0-255 0~100% linear

22 Green 3 0-255 0~100% linear

23 Blue 3 0-255 0~100% linear

Table des matières

Autres manuels PR Lighting Matériel de DJ

PR Lighting

PR Lighting XLED 250 BEAM Manuel utilisateur

PR Lighting

PR Lighting CSL 1037 Manuel utilisateur

PR Lighting

PR Lighting JNR DOT BEAM Manuel utilisateur

PR Lighting

PR Lighting XR440 BEAM Manuel utilisateur

PR Lighting

PR Lighting PR-6000 Spot Manuel utilisateur

PR Lighting

PR Lighting XR-230 BEAM Manuel utilisateur

PR Lighting

PR Lighting ARC LED 3108 Manuel utilisateur

PR Lighting

PR Lighting LED Studio 3201D Manuel utilisateur

PR Lighting

PR Lighting XR 380 Beam Manuel utilisateur

PR Lighting

PR Lighting PR-8330 Manuel utilisateur

PR Lighting

PR Lighting XRLED 1200 SPOT Manuel utilisateur

PR Lighting

PR Lighting StarBrite Manuel utilisateur

PR Lighting

PR Lighting PR-2302 Manuel utilisateur

PR Lighting

PR Lighting MEGA 4000 Manuel utilisateur

PR Lighting

PR Lighting PILOT 300 Manuel utilisateur

PR Lighting

PR Lighting AQUA LED 730 FRAMING Manuel utilisateur

PR Lighting

PR Lighting Pro Stage 150 RGBW 19 Manuel utilisateur

PR Lighting

PR Lighting Junior JNR Minifresnel 100MZ-W Manuel utilisateur

PR Lighting

PR Lighting AQUA 580 BEAM Manuel utilisateur

PR Lighting

PR Lighting JUNIOR JNR-8146C Manuel utilisateur

PR Lighting

PR Lighting AQUA LED 1800 FRAMING Manuel utilisateur

PR Lighting

PR Lighting XR 1700 FRAMING Manuel utilisateur

PR Lighting

PR Lighting JNR BWS 350 Manuel utilisateur

PR Lighting

PR Lighting PR-8102 Manuel utilisateur

Manuels Matériel de DJ populaires d'autres marques

ALPHA LITE

ALPHA LITE ALPHA 1500 Manuel du propriétaire

Chauvet

Chauvet OVATION E-930VW Manuel utilisateur

Zumtobel

Zumtobel APHRODITE Home Manuel utilisateur

Snow Masters

Snow Masters Zig Oscillator Manuel utilisateur

EuroLite

EuroLite 50530554 Manuel utilisateur

Beamz

Beamz BUV243 Manuel utilisateur

thomann

thomann Stairville DJ Lase 40-G MK-III Manuel utilisateur

Eagletone

Eagletone 6 Eyes Flower Manuel utilisateur

EuroLite

EuroLite FLD-1508 Manuel utilisateur

Technical Pro

Technical Pro LG8xSEA Manuel utilisateur

JB Systems

JB Systems Lounge Laser DMX Manuel utilisateur

Lightmaxx

Lightmaxx Vega Halo 90 Manuel utilisateur

Elation

Elation FUZE WASH Z350 Manuel utilisateur

Maverick

Maverick MK3 WASH Manuel utilisateur

Infinity

Infinity TF-260C7 Fresnel Manuel utilisateur

Chauvet

Chauvet EVE E-50Z Manuel utilisateur

Eliminator Lighting

Eliminator Lighting E 138 Manuel utilisateur

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manuel utilisateur