PR Lighting PR-8330 Manuel utilisateur

BLINDER 360

PR-8330

This product manual contains important information about the safe installation and use of this projector.

Please read and follow these instructions carefully and keep this manual in a safe place for future reference.

PR LIGHTING LTD.

http://www.pr-lighting.com

2/20

INDEX

1. SAFETY AND WARNINGS

2. INSTUCTIONS

●CLEANING AND MAINTENANCE

●TROUBLESHOOTING

3. APPEARANCE

4. INSTALLATION

●RIGGING

●POWER CONNECTIONS

●DMX CONTROL CONNECTION

●DMX TERMINATOR

5. SETUP AND CONFIGURATION

●FRONT PANEL OPERATION

●DMX START ADDRESS

●DMX WIRELSESS CONTROL

●STAND-ALONE MODE

●MASTER/SLAVE MODE

● SOUND MODE

6.OPERATION MENU

7. DMX PROTOCOL

8. LED INDICATION

9.TECHNICAL DATA

10.CIRCUIT DIAGRAM AND PCB CONNECTIONS

●CIRCUIT DIAGRAM

●PCB CONNECTIONS

11.COMPONENT ORDER CODES

ACCESSORIES

The following items are supplied with the projector and please check:

Name Quantity Unit Remark

G clamps 1 Pc

Safety cord 1 Pc

User manual 1 Pc

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change

without notice. Whilst every care is taken in the preparation of the manual we reserve the right to change specifications in the

course of product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any

consequence arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are

in good condition before installation and use. Should there be any damage caused by transportation, consult your dealer and

do not use the unit. Any damage caused by improper use will not be assumed by the manufacturer and / or dealer.

Note: For the products made by Guangzhou PR lighting Ltd, the warranty for the whole product is one year starting from

the delivery date but the light source is not within the warranty.

3/20

1. SAFETY AND WARNINGS

NOTE

Before a projector’s installation, power-on, operation and maintenance, please carefully read

the safety information hereinafter!

The following safety signs are used in the user manual.

Warning

User

Manual

Electrical

shock

Goggles

Protective

Gloves

Flames

High

Temperature

● When unpacking , check if there is transportation damage before using the projector. Should there be any

damage caused by transportation, consult your dealer and do not use it.

●The manufacture is not responsible for loss caused by the user not following the manual or changing the projector

as he/she likes

●Please be noted that the damage caused by changing the projector at will is not warranted.

● Do not hesitate to contact the dealer or the manufacturer if any questions or advice.

● The projector is only for indoor and outdoor use, IP20.

● Keep this unit away from excessive heat and wet and humid areas . Do not allow the contact with any corrosive

liquids and water.

●The projector should be kept away from high temperature, fire, electrical surge, vibration and strong light while

being operated

●The projector is only intended for installation, operation and maintenance by qualified personnel. And the

operation must strictly follow the procedures in the manual

●No repairable parts in the projector and do not open covers for maintenance by yourself.

●Don’t look straightly into the light sources especially for epileptics, otherwise eyes will be burned.

●Do not connect this device to any type of dimmer pack

●After lamp switched on, the minimum distance between the projector and illuminated surface is 5m

●lens and other optical parts shall be replaced immediately if they have deformed or been damaged, otherwise the

light output will be compromised.

●Before operation, please confirm that all covers(housing) are on and screws tightened. It’s forbidden to use a

projector while covers(housing)are off

●Keep the lamp clean and do not touch it with bare hands.

●While operating it, wear protective items.

●Any electrical connection must be carried out by a qualified person .

●Before installation, please confirm the voltage supplied matches what is required for the projector

●Each projector must be properly earthed and installed as per related electrical standards.

●Do not use power cord with its insulator damaged and connect the power cord with other cables.

●If the projector is not used or under cleaning,, please hold the plug and unplug it. Do not unplug it forcefully

or by pulling the power cable.

●All power cords must conform to related safety and regulations

●While being operated, the projector should not be under rains or in humidity.

●Do not switch on and off the projector constantly in very short intervals, otherwise the light source’s and other

4/20

electrical parts’ life will be shortened .

●There are safety cord holes at the bottom of the base of a projector. In view of safety, please run the safety

cord supplied through the safety cord holes for safety support.

●Before any installation, maintenance and cleaning work, please ensure the projector is disconnected from

power mains.

●After running for 5minutes, the temperature of the housing of the projector is 55℃.After stable operation ,

its temperature is 70℃.

●While the lamp is stricken for the first time, there will be smoke and strange smell. It’s normal and does not

mean the projector has some defects.

●Do not mount the projector directly on inflammable surface.

●Do not project the beam straightly on combustible items and the minimum distance between the

projector and illuminated items is 5m.

●A projector should be installed with good ventilation and the minimum distance between the projector

and walls is 50cm. At the same time, please ensure the fans and air inlets and outlets are workable.

2. INSTRUCTIONS

●CLEANING AND MAINTENANCE

If a projector can’t start. Please check if the fuse is blown up. If it does, replace it with a new fuse with same ratings. And the

projector has over-temperature protective device. If the temperature is too high, the protective device will be triggered to shut the

projector off. When it happens, please check if the fans run normally or fan shield is blocked by dust. After the issue is solved,

restart the projector.

The accumulation of oil, smoke and dust on the lens will compromise the light output. Cleaning a projector is very necessary to

ensure a reliable use of it. Cooling fans need to be cleaned every 15days. Internal lens, reflector and hot mirror need to be cleaned

periodically to optimize light output.

Cleaning frequency is to be decided by operations and its environment. Use soft cloth and normal detergent for glass for cleaning

work. It’s advised external optical system be cleaned every 20days and internal optical systems every 30/60days. Keep lens clean

and do not touch optical parts with bare hands.

●Before any maintenance and cleaning, please ensure the project is off the power

●Only qualified person is allowed to do maintenance

●During maintenance and before maintenance, the projector must be off power.

●To avoid internal damage, sun light or other light mustn’t penetrate into the projector via front lens

whether it runs or not

●Do not use alcohol or other organic solvent to clean the housing to avoid damage.

●Do not use any solvent with chemical elements to clean color filters or hot mirror.

●TROUBLESHOOTING

PROBLEM ACTION

The projector doesn’t switch on

 The power cord is not connected well

 The Power Switch is bad or not connected well. A qualified technician is

needed to fix it.

 The control board is not connected well and a qualified technician is

needed to fix it.

The projector can be on but LED lamps are not

on and not controlled

 LED lamp board is not connected well and a qualified technician is

needed to fix it

The projector can emit light, but can’t be

controlled by the controller

 Check if the DMX start address is set properly

 Check if XLR cable is damaged or not

Heavily Defective Beam  High ambient temperature causes the projector to be over heat and

necessary cooling measures are needed.

5/20

3. APPEARANCE

4. INSTALLATION

● RIGGING

Before moving a projector, Please lock Pan and Tilt.

Take 1 clamps and 1 safety cords out from the package and mount 1 clamps on the underside of fixture with 2 retainers attached to

each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. (See the WARNING on the underside of

the base as shown above) Always ensure that the projector is firmly anchored to avoid vibration and slipping whilst functioning.

Always ensure that the structure that you are going to mount the projector is secure and is strong enough to support the weight of the

fixture.

6/20

WARNING:

●The projector MUST be lifted or carried by the HANDLES instead of clamps.

●.For safety the safety cord should afford 10 times the Projector’s weight.

● POWER CONNECTION

Connect the power cord as follows:

L (live) =brown

E (earth) =yellow/green

N (neutral) =blue

Before power connection, please ensure the power supplied must match what the nameplate says. It is recommended that each

projector be connected with power separately so that they may be individually switched on and off.

Note: If projectors are connected in series, please connect POWERIN port of the 1st projector with the Power Mains, then

connect its POWER OUT with POWER IN of the 2nd projector, and so on till all fixtures are connected. If the voltage supplied

is 200V-240V, the maximum projectors connected is 5pcs, if it is 100V-120V, the maximum is 3pcs. The diameter of the cores

of the wires for the Power in/out cables must be equal or bigger than 2.5mm2 .

●The earth wire(yellow/green) must be connected to the ground. And electrical connection must be in

accordance with the standards concerned.

●If any questions about the electrical installation, do not continue but consult a qualified electrician.

●DMX CONTROL CONNECTION

Connection between controller and projector and between one projector and another must be made with a twin-screened cable, with

each wire having at least a 0.5mm in diameter. Connection to and from the projector is via cannon 5 pin (which are included with the

projector) or 5 pin XLR plugs and sockets. The XLR's are connected as shown in the figure above.

Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. XLR plugs and sockets

mustn’t be connected in any way other than mentioned in the above figure. The projector accepts digital control signals in protocol

DMX512 (1990).

Connect the controller’s DMX output to the first fixture’s DMX input, and connect the first fixture’s DMX output to the second

fixture’s DMX input and connect the rest fixtures in the same way. Eventually connect the last fixture’s DMX output to a DMX

terminator as shown in the figure below.

7/20

120

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor

across pins 2 and 3 in an XLR plug

and insert into the DMX out socket

on the last unit in the chain.

PIN 3

PIN 2

●DMX TERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents

electrical noise from disturbing and corrupting the DMX control signals.

The DMX terminator is simply an XLR connector with a 120 (ohm) resistor connected across pins 2 and 3, which is then plugged

into the output socket on the last projector in the chain. The connections are illustrated below.

8/20

5. SETUP AND CONFIGURATION

●FRONT PANEL OPERATION

Projector configuration can be set conveniently via push buttons and LCD screen.

Launch the projector and press button ENTER for more than 5 seconds to unlock the panel, the LCD will show the function menu of

the projector, each main menu has its submenus and each submenu has a specific function. For details, please see the

“OPERATION MENU” section.

Press button UP or DOWN if you want to browse through the various Setup Options.

Press button ENTER to save your settings or enter the submenu.

Press button UP or DOWN to change values(plus or minus)

Press button FUNC, it will return to the upper menu. If button FUNC not pressed, the default will show display status automatically.

● DMX START ADDRESS

Each projector must be given a DMX start address so that the correct projector responds to the correct control signals. This DMX start

address is the channel number from which the projector starts to “listen” to the digital control information being sent out from the

controller. The projector has 2DMX modes. There are standard and extended modes. For example standard mode has 18channels, so

set the No. 1 projector’s address 001, No. 2 projector’s address 019, No. 3 projector’s address 037, No. 4 projector’s address055, and

so on.

Launch the projector. Press button ENTER more than 2seconds to unlock panel.

Press button ENTER to display DMX address;

Press button UP and DOWN, you can set the address;

Press button ENTER to confirm; after powered on next time, the default will be last value saved

Press button FUNC, it will return to the upper menu

●DMX WIRELESS CONTROL (If the projector has the function)

The projector has wireless control function with wireless receiver module and antenna for remote control.

The setup of it is below:

1. Enter into the projector’s menu. Select the menu “Config Settigns” via the bottoms of UP and DOWN

2. Select DMX control Mode---- Wireless First (Note: do not select XLR ONLY),then wireless indication in the

front panel will be on, meaning wireless control function is activated.

Only after the projector is linked with a transmitter, can it receive wireless signal sent by the transmitter. If unlinking it,

Press “Enter” for the menu of Unlink Wireless under the upper level menu of Config Settigns .

●STAND-ALONE MODE

Operate the projector without connecting with a controller, enable the master mode through the operation panel, the

projector will run in Stand-Alone mode automatically.

DMX address can be set at any number within 512.

9/20

●MASTER/SLAVE MODE

Many projectors can run synchronously in the Master/Slave mode by linking them with each other. First,

connect the first fixture’s DMX output to the second fixture’s DMX input using XLR-XLR control cable and then connect the second

fixture’s DMX output to the third fixture’s DMX input, and so on until all projector are connected in this way. Eventually connect the

last fixture’s DMX output to a DMX terminator. Set 1st projector as the master and others are Slaves.

Start Addresses of all Slaves are 001; Operation mode of the Master can be set any mode for a Master’ and Slaves’ operation mode can

be set accordingly.

After Powered on, the group will run in Master/Slave Mode

● Sound Operation

To select different level(1-100) of sound sensitivity based on different operating environment under sound operation under

Operation Mode. There are several different(0-8) sound effects for different operating environment under Sound

Operation.

Note: If several fixtures in series under Master/Slave mode, Only Master responds to external sound.

6. OPERATION MENU

1st level menu

2nd level menu

3rd level menu

4th level menu

DMX Address

XXX

(1~512

）

Reset

Are You Sure

Config Set

DMX Mode

（Default：Standard）

Standard12

Extended 20

Loss of DMX

（Default: Normal

Time Out）

Normal Time Out

Hold Last Value

10/20

Wireless Mode

（Default：XLR First）

XLR First

XLR Only

Wireless Only

Wireless First

Wireless To XLR

Master/Slave

（Default：SLAV）

Slave

Master

Display Mode

（Default：

offafterDelay）

OffAfterDelay

On Always

Display Reverse

（Default：Off）

Off

Language

（Default：Egnlish）

English

Chinese

Sound Level

1～100

DisplayContrast

Pan amend

XXX

127

Tilt amend

XXX

127

Unlink Wireless

YES

ResetUserData

YES

ResetOptionSet

YES

FactorySettings

YES

ParameterTransm

YES

Option Set

Pan DMX Invert

（Default：Off）

Off

Tilt DMX Invert

（Default：Off）

Off

Pan Tilt Swap

（Default：Off）

Off

Pan angle Range 360

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels PR Lighting Matériel de DJ

PR Lighting

PR Lighting AQUA LED 600 SPOT Manuel utilisateur

PR Lighting

PR Lighting LED Studio 3200T Manuel utilisateur

PR Lighting

PR Lighting OMEGA Manuel utilisateur

PR Lighting

PR Lighting PR-8802 Manuel utilisateur

PR Lighting

PR Lighting PR-6000 Spot Manuel utilisateur

PR Lighting

PR Lighting JNR DOT BEAM Manuel utilisateur

PR Lighting

PR Lighting XLED 6007 Manuel utilisateur

PR Lighting

PR Lighting Theatre Master PR-3010 Manuel utilisateur

PR Lighting

PR Lighting JNR BWS 350 Manuel utilisateur

PR Lighting

PR Lighting XR440 BEAM Manuel utilisateur

PR Lighting

PR Lighting Pro Stage 150 RGBW 19 Manuel utilisateur

PR Lighting

PR Lighting PR-8110 Manuel utilisateur

PR Lighting

PR Lighting XLED 3007 Manuel utilisateur

PR Lighting

PR Lighting MEGA 4000 Manuel utilisateur

PR Lighting

PR Lighting XLED 1037 Manuel utilisateur

PR Lighting

PR Lighting XR 1000 Framing Manuel utilisateur

PR Lighting

PR Lighting PR-8102 Manuel utilisateur

PR Lighting

PR Lighting XR480 BEAM Manuel utilisateur

PR Lighting

PR Lighting AQUA LED 1800 FRAMING Manuel utilisateur

PR Lighting

PR Lighting XPar 336-W Manuel utilisateur

PR Lighting

PR Lighting LED Studio 3300T Manuel utilisateur

PR Lighting

PR Lighting XPar 1012 Manuel utilisateur

PR Lighting

PR Lighting XLED 250 BEAM Manuel utilisateur

PR Lighting

PR Lighting SOLO 575 Manuel utilisateur

Manuels Matériel de DJ populaires d'autres marques

ALPHA LITE

ALPHA LITE ALPHA 1500 Manuel du propriétaire

Chauvet

Chauvet OVATION E-930VW Manuel utilisateur

Zumtobel

Zumtobel APHRODITE Home Manuel utilisateur

Snow Masters

Snow Masters Zig Oscillator Manuel utilisateur

EuroLite

EuroLite 50530554 Manuel utilisateur

Beamz

Beamz BUV243 Manuel utilisateur

thomann

thomann Stairville DJ Lase 40-G MK-III Manuel utilisateur

Eagletone

Eagletone 6 Eyes Flower Manuel utilisateur

EuroLite

EuroLite FLD-1508 Manuel utilisateur

Technical Pro

Technical Pro LG8xSEA Manuel utilisateur

JB Systems

JB Systems Lounge Laser DMX Manuel utilisateur

Lightmaxx

Lightmaxx Vega Halo 90 Manuel utilisateur

Elation

Elation FUZE WASH Z350 Manuel utilisateur

Maverick

Maverick MK3 WASH Manuel utilisateur

Infinity

Infinity TF-260C7 Fresnel Manuel utilisateur

Chauvet

Chauvet EVE E-50Z Manuel utilisateur

Eliminator Lighting

Eliminator Lighting E 138 Manuel utilisateur

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manuel utilisateur