Powerware 9150 Manuel utilisateur

Powerware®9150

User’s Guide

8kVA-12.5kVA

www.powerware.com

02/20/2001

FCC Statement

The Powerware

9150 UPS configurations vary. Some configurations may or may not be classified by the Federal

Communications Commission (FCC) as a Class A device. If your Powerware 9150 unit is classified by these standards, the

corresponding information applies:

Class A

NOTE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause interference to radio

communications. Operation of this equipment in a residential area is likely to cause interference in which case the user will

be required to correct the interference at his own expense.

Powerware and OnliNet are registered trademarks and ConnectUPS is a trademark of Powerware Corporation.

in any way without the express written approval of Powerware Corporation.

Table of Contents

Powerware®9150 User’s Guide

www.powerware.com

TABLE OF CONTENTS

1 Introduction 1....................................................

UPS Model and BatteryConfigurations 2..............................................

Load Requirements 2.........................................................

BatteryTimes 3.............................................................

2 Safety Warnings 5.................................................

Sikkerhedsanvisninger 7.........................................................

Belangrijke Veiligheidsinstructies 8..................................................

Tärkeitä turvaohjeita 9..........................................................

Consignes de Sécurité 10.........................................................

Wichtige Sicherheitsanweisungen 11.................................................

Importantiistruzionidi sicurezza 12..................................................

Viktig Sikkerhetsinformasion 13.....................................................

Regulamentos de Segurança 14.....................................................

Requisitos de seguridad 15........................................................

Viktig säkerhetsinformation 16......................................................

3 Installation 17.....................................................

UPSStorage 17................................................................

UPSSetup 18..................................................................

Floor Loading 18..............................................................

SeismicMounting 19..........................................................

Selecting an Installation Option 20...................................................

UPSInstallation 20..............................................................

UPS with OptionalPDM Installation 25................................................

ExternalBattery Cabinet Installation 30...............................................

UPSStartup 33.................................................................

Bypass Startup 33............................................................

Normal Mode Startup 34.......................................................

UPS Startup on Battery 35......................................................

Configuring Voltage and Frequency 36................................................

Automatic Configuration Mode 36.................................................

Manual Configuration Mode 37...................................................

Table of Contents

ii Powerware®9150 User’s Guide

www.powerware.com

4 Operation 39......................................................

ControlPanelFunctions 39.........................................................

NEEDNEW LOGO 39.............................................................

Operating Modes 41.............................................................

NormalMode 42.............................................................

Bypass Mode 42.............................................................

BatteryMode 42.............................................................

UPSShutdown 43...............................................................

Using the Maintenance BypassSwitch 44..............................................

Computer and Alarm Connections 46.................................................

NEEDNEW LOGO 46.............................................................

Hardware Installation 46.......................................................

RS-232 Serial Data Interfaces 47..................................................

Isolated Alarm RelayInterface 49.................................................

Remote Emergency Power-off Input 50..............................................

Efficiency Optimizer Function 50.....................................................

5 Specifications 51..................................................

Powerware 9150 TechnicalSpecifications 51...........................................

Powerware 9150 ModelSpecifications 52.............................................

PhysicalSpecifications 53.........................................................

Environmental and Safety Specifications 54............................................

ExternalBattery Cabinet Specifications 54.............................................

6 Troubleshooting 55.................................................

Silencing the Alarm 56...........................................................

Service and Support 57...........................................................

Upgrading 57..................................................................

Powerware®9150 User’s Guide

www.powerware.com

CHAPTER 1

INTRODUCTION

The Powerware

9150 is a double-conversion, online uninterruptible

power supply (UPS) for protecting computer systems and other

intelligent devices.

The UPS provides a steady, well-regulated power supply for your

computing and communications equipment, while protecting it from the

frequent irregularities that are inherent in commercially available power.

Voltage spikes, power surges, brownouts, and power failures have the

potential to corrupt critical data, destroy unsaved work sessions, and in

some instances, damage expensive hardware.

With the Powerware 9150, you can safely eliminate the effects of

electrical line disturbances and guard the integrity of your systems and

equipment. Figure 1 shows the Powerware 9150 UPS.

29.72

(755 mm) 15.75

(400 mm)

28.23

(717 mm)

Figure 1.The Powerware 9150 UPS

Introduction

2Powerware®9150 User’s Guide

www.powerware.com

UPS Model and Battery Configurations

There are two important considerations when selecting the UPS model

and battery configuration to properly safeguard your equipment:

The UPS output power rating (VA) should be specified according to

the total power demand of the equipment to be protected. Some

margin should be allowed for potential expansion of the protected

system,and for possible inaccuracy in calculating or measuring the

actual power requirement.

The battery should be sized according to the desired backup time.

The backup time is longer if the load is less than the nominal power

rating of the UPS.

Load Requirements

Determine the total load requirements, in volt-amperes (VA), of the

equipment to be protected by the UPS. The UPS load should not exceed

the UPS rating. To determine the total load requirements:

1. Obtain the load ratings from either the nameplate or operator’s

manual of the equipment to be protected by the UPS. The

ratings are listed in either watts (W), amperes or amperes max

(A), or volt-amperes.

2. If the rating is in watts, multiply by 1.4 to obtain the VA

requirement (this is the typical relationship between watts and

volt-ampere ratings in most computing equipment).

If the rating is in amperes or amperes max, multiply by the

input voltage to obtain the VA requirement.

3. Add all of the resultant VA ratings together to obtain the total

load requirements of the equipment to be protected (see

Figure 2).

3 COMPUTERS 3 MONITORS EXTERNAL

MODEM

3 x 300 WATTS X 1.4 = 1260 VA 3x2AMPSx240V = 1440 VA 50 VA

1260 VA + 1440 VA + 50 VA = 2750 VA (Total Load Requirements)

300 WATTS

EACH 2AMPS

EACH 50 VA

Figure 2. Volt-Amperes Calculation Example

Introduction

Powerware®9150 User’s Guide

www.powerware.com

If the total load requirements of the equipment exceeds the capacity of

the UPS, you must either reduce the number of pieces of equipment, or

use a UPS with a larger load capacity.

NOTE Line-to-neutralloads (100V- 127V) should be balanced between L1/A and

L2/B.

When deciding on which pieces of equipment to remove from the UPS,

select equipment that has a lower priority for power protection.

Computers, monitors, and modems typically have a higher priority

because they could be processing or transmitting data when a power

outage occurs.

Battery Times

The Powerware 9150 UPS has internal batteries with run times up to

17 minutes.If additional run time is required, optional external battery

cabinets (EBCs) canbe purchased.There are two EBC models available:

EBC-48 and EBC-96.The EBC-48 modelcontains 48 batteries and the

EBC-96 model contains 96 batteries. The following table shows

approximate battery times for both internal battery models and the

optional EBC configurations. The times shown in the EBC rows are

cumulative and include the internal battery time.

Powerware 9150 Approximate Battery Times (in Minutes at Full Load)

Model8kVA Model10kVA Model 12.5kVA

UPS with

32 Batteries* 10 8

Internal Batteries 48 Batteries 17 13 9

1 EBC-48 Cabinet 41 31 23

1 EBC-96 Cabinet 69 52 40

2 EBC-96 Cabinets 133 101 77

3 EBC-96 Cabinets 206 157 119

4 EBC-96 Cabinets 284 217 165

5 EBC-96 Cabinets 368 281 213

*EBCs are not available for the 32-battery model. Refer to the serial nameplate; if DC voltage

on the nameplate is 192V, EBCs cannot be used. To use EBCs, DC voltage must be 288V.

Introduction

4Powerware®9150 User’s Guide

www.powerware.com

If a powerfailure outlasts the backup time, the UPS shuts down in order

to prevent a total discharge of the battery. When utility is restored, the

UPS starts automatically, providing power to the critical load and

charging the battery bank.

Powerware®9150 User’s Guide

www.powerware.com

CHAPTER 2

SAFETY WARNINGS

The only user operations permitted are:

Starting up and shutting down the UPS

Operating the user interface

Connecting data interface cables

Monitoring the UPS with power management software

WARNING

Only qualified service personnel(such asa licensed electrician) should perform the

UPS installation and initial startup. Riskof electrical shock.

These operations must be performed according to the instructions in

this manual. During any of these operations, you must perform only the

listed operations. Any deviation from the instructions could be

dangerous.

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS. This manual containsimportant instructions that you

should follow during installation and maintenance of the UPSand batteries. Please

read allinstructions before operating the equipment and save this manualfor future

reference.

Safety Warnings

6Powerware®9150 User’s Guide

www.powerware.com

DANGER

ThisUPScontainsLETHAL VOLTAGES. All repairs and service should be performed

byAUTHORIZED SERVICE PERSONNEL ONLY. There are NO USER

SERVICEABLE PARTS inside the UPS.

CAUTION

Output overcurrent protection and disconnect switch must be provided by others

(see table on page 21).

To reduce the risk of fire, connect only to a circuit provided with 70 amperes

maximum branch circuit overcurrent protection in accordance with the National

Electrical Code,ANSI/NFPA 70 (see table on page 21).

Batteriescan present a risk of electrical shock or burn fromhigh short circuit

current.Observe proper precautions. Servicing should be performed byqualified

service personnelknowledgeable of batteries and required precautions.Keep

unauthorized personnel away frombatteries.

Proper disposalof batteriesisrequired.Refer to your localcodes for disposal

requirements.

ThisUPScontainsitsownenergy source(batteries).The UPSoutputmaycarrylive

voltage even when the UPS is not connected to an AC supply.

Neverdisposeofbatteriesina fire.Batteriesmayexplodewhenexposedtoflame.

To reduce the risk of fire or electric shock, installthisUPS in a temperature and

humiditycontrolled,indoorenvironment,freeofconductivecontaminants.Ambient

temperature must not exceed 104



F(40



C).Do not operate near water or

excessive humidity (95% max).

Table des matières

Autres manuels Powerware Alimentation

Powerware

Powerware 3115 Manuel utilisateur

Powerware

Powerware 4500 Manuel utilisateur

Powerware

Powerware 30-160kVA Manuel utilisateur

Powerware

Powerware 208/120V Manuel utilisateur

Powerware

Powerware 5115 Manuel utilisateur

Powerware

Powerware 3110 Manuel utilisateur

Powerware

Powerware 3105 Manuel utilisateur

Powerware

Powerware 5075 kVA Manuel utilisateur

Powerware

Powerware 3110 Manuel utilisateur

Powerware

Powerware 9315 Instructions d'installation et d'utilisation

Powerware

Powerware 9350 Manuel utilisateur

Manuels Alimentation populaires d'autres marques

Monacor

Monacor PS-12CCD Manuel utilisateur

VOLTIMA

VOLTIMA MagicBox 15 Manuel utilisateur

Agilent Technologies

Agilent Technologies 6032A Manuel utilisateur

Miller

Miller Auto Deltaweld 452 Manuel utilisateur

BCP

BCP PUOUBK Feuille d'instructions

HC 2210 Manuel utilisateur

Puls

Puls CT5.241 Manuel utilisateur

OCZ

OCZ ZX1250W Manuel utilisateur

iseg

iseg ECH 238 Manuel utilisateur

Power

Power XXL A Series Manuel utilisateur

Agilent Technologies

Agilent Technologies 6631B Manuel utilisateur

Renogy

Renogy PHOENIX 300 Manuel utilisateur

HP 6200B Manuel de service

Epson

Epson Stylus Scan 2500 Manuel d'utilisation

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manuel utilisateur

Puls

Puls MiniLine ML50.100 Manuel utilisateur

Puls

Puls AS-Interface SLA4.100 Manuel utilisateur

Kenwood

Kenwood PS-60 Manuel utilisateur