PowerVision PowerDolphin Manuel utilisateur

PowerDolphin

V1.0

快速入门指南

Quick Start Guide

クイックスタートガイド

目录 /CONTENTS

快速入门指南



Quick Start Guide



クイックスタートガイド







󾗲󾗹

PowerDolphin

PowerDolphin is a water-surface vehicle that can sail autonomously. Equipped with a robotic camera

arm the PowerDolphin can shoot 4k video and take12 MP photos above and below the water surface.

In addition, you can attach the PowerSeeker sonar to the bottom of the PowerDolphin, to locate sh,

check water temps, and render terrains. You can also attach our bait container or attach a shing line

to the payload feature on the back of the PowerDolphin for precise bait drops. The remote controller

and the Vision+ 2 App provide real-time image transmission and many other features.

On/Off button

Radio antenna

Propeller

Payload system

Hook

Fitting pin

Camera electric joint

Camera manual joint

Battery cover

Rubber plug

microSD card slot

Reset button

Micro USB port

Intelligent battery

Fish nder port

You can use the remote controller to operate your PowerDolphin wirelessly with a range of up to 2400

ft, and display real-time zero latency high resolution image’s back to your mobile device through the

Vision+ 2 App. In addition, the collapsible mobile device stand folds right into the remote and can

hold any size iOS and android mobile phone.

Remote

Mobile device stand

Antenna

Control stick

Mode buttons

Cruise mode (C)

Normal mode (N)

Underwater mode (U)

Lock/Unlock button

Smart return button

Custom button

(Unhook/Bait button by default;

can be customized in the App)

Power button

Charging port (Micro USB)

Photo button

Video button

Image transmission port (USB)

16 Camera joint control thumbwheel

• Underwater mode (U): suitable for low-speed, underwater scenarios like snorkeling.

The maximum speed is restricted; the camera electric joint can be adjusted for many different views.

• Normal mode (N): This mode is for general high-speed fun and water-surface FPV

scenarios.

The maximum speed is 10mph; the camera electric joint in N mode is set to its initial position and

cannot be adjusted into the water.

• Cruise mode (C): Cruise control function. Take off, release the throttle stick and just steer

the PowerDolphin.

The maximum speed is 10mph; the camera electric joint in C mode is set to its initial position and

cannot be adjusted into the water.

[Notes]:To Enter Cruise mode: Hold the throttle stick in a position for 2s then release.

To Exit Cruise mode: Just move the throttle stick again to regain speed control.

Fish nder

Fishing line connector Charging port Fish luring lamp

Introduction

Installation

[Notes]:When the PowerSeeker is connected to another mobile device, it cannot connect to

PowerDolphin. Make sure the connection to the PowerSeeker of others phones before using with

PowerDolphin.

Charging and battery level

Charging

Download the App to watch the video tutorial of PowerDolphin

Please scan the QR code or go to your App store to download Vision+ 2,

and watch the video tutorial in the App.

Fish nder charging portFish nder charging portRemote charging port

2. Fish nder

Battery level

1. Remote (LED indicators)

>60% <20%20%-60%

3. Intelligent battery

Level

Low High

Prepare PowerDolphin

1. Install the battery and secure it into place.

1. Ensure that the rubber plug is secured into place to guarantee water prong.

2. Make sure that the battery-sealing ring is intact before installing the battery. Damage to the

rubber seal will result to a unusable battery. The rubber seal can be found under the lip of the

battery top.

Autres manuels pour PowerDolphin

Table des matières

Langues :

Autres manuels PowerVision Drone

PowerVision

PowerVision PowerRay Manuel utilisateur

PowerVision

PowerVision PowerEgg X Manuel utilisateur

PowerVision

PowerVision PowerEgg Series Manuel utilisateur

PowerVision

PowerVision PowerEgg X Manuel utilisateur