Powerplus POWDP8031 Manuel utilisateur

 POWDP8031 EN 
Copyright © 2020 VARO P a g e | 1www.varo.com 
1DOMAIN OF USE...................................................................................................2 
2DESCRIPTION (FIG. A)..........................................................................................2 
3SYMBOLS..............................................................................................................2 
4GENERAL POWER TOOL SAFETY WARNINGS.................................................3 
4.1 Working area.........................................................................................................3 
4.2 Electrical safety.....................................................................................................3 
4.3 Personal safety .....................................................................................................3 
4.4 Power tool use and care.......................................................................................4 
4.5 Service...................................................................................................................4 
5ADDITIONAL SAFETY INSTRUCTIONS FOR BATTERIES AND CHARGERS...4 
5.1 Batteries.................................................................................................................5 
5.2 Chargers................................................................................................................5 
6SAFETY WARNING FOR WORK-LIGHT...............................................................5 
7OPERATION...........................................................................................................5 
7.1 Charging the battery pack....................................................................................5 
7.1.1 Charging indication .................................................................................................6 
7.2 Battery capacity indicator (Fig.1a) ......................................................................6 
7.3 Inserting and removing the battery (Fig 2) .........................................................7 
7.4 Adjusting the light direction (Fig. 3)....................................................................7 
7.5 ON/OFF switch button (Fig 4) ..............................................................................7 
7.6 Hanging hook........................................................................................................7 
8CLEANING AND MAINTENANCE.........................................................................7 
9TECHNICAL DATA ................................................................................................8 
10 WARRANTY...........................................................................................................8 
11 ENVIRONMENT .....................................................................................................9 
 

POWDP8031 EN

PORTABLE LED WORKLIGHT 20 V (NO BATTERY)

POWDP8031

1 DOMAIN OF USE

Outdoor or indoor usage such as jobsite, garden, studio and workshop.

WARNING! Read this manual and general safety instructions carefully

before using the appliance, for your own safety. Your power tool should

only be passed on together with these instructions.

2 DESCRIPTION (FIG. A)

1. Work light head

2. Bracket

3. Adjustable knob

4. Bracket seat

5. Hanging hook

6. Rubber pad

7. Handle

8. Battery pack (not included)

9. ON/OFF button

10. Power level button

11. Charger (not included)

3 SYMBOLS

In this manual and/or on the machine the following symbols are used:

Denotes risk of

personal injury or

damage to the

tool.

In accordance

with essential

requirements of

the European

directive(s).

Read manual

before use.

Class III - tool in

which protection

against electric

shock relies on

supply at safety

extra-low voltage

and in which

voltages higher

than those of safety

extra-low voltages

are not generated.

Ambient

temperature 40 °C

max. (only for

battery).

Do not expose

charger and

battery pack to

water.

POWDP8031 EN

Use battery and

charger only in

closed rooms.

Do not incinerate

battery pack or

charger.

4 GENERAL POWER TOOL SAFETY WARNINGS

Read all safety warnings and instructions. Failure to heed warnings and follow instructions

may result in electric shock, fire and/or serious injury. Keep safety warnings and

instructions for future reference. The term "power tool" in the safety warnings refers to your

mains- operated (corded) power tool or battery- operated (cordless) power tool.

4.1 Working area

▪Keep working area clean and well lit. Untidy and dark areas can lead to accidents.

▪Do not operate power tools in potentially explosive surroundings, for example, in the

presence of inflammable liquids, gases or dust. Power tools create sparks which may

ignite the dust or fumes.

▪Keep children and bystanders at a distance when operating a power tool.

Distractions can cause you to lose control of it.

4.2 Electrical safety

▪Always check that the power supply corresponds to the voltage on the rating plate.

▪Power tool plugs must match the outlet. Never modify the plug in any way. Do not

use adapter plugs with earthed power tools. Unmodified plugs and matching outlets

will reduce the risk of an electric shock.

▪Avoid body contact with earthed surfaces such as pipes, radiators, kitchen ranges

and refrigerators. There is an increased risk of an electric shock if your body is

earthed.

▪Do not expose power tools to rain or wet conditions. If water gets inside a power tool,

it will increase the risk of an electric shock.

▪Do not damage the cord. Never use the cord for carrying, pulling or unplugging the

power tool. Keep the cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of an electric shock.

▪When operating a power tool outdoors, use an extension cable suitable for outdoor

use. Using a cord suitable for outdoor use reduces the risk of an electric shock.

▪If operating a power tool in a damp location is unavoidable, use a power supply

protected by a residual current device (RCD). Using an RCD reduces the risk of an

electric shock.

4.3 Personal safety

▪Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use a power tool when you are tired or under the influence of

drugs, alcohol or medication. A moment of inattention when operating a power tool

may result in serious personal injury.

▪Use safety equipment. Always wear eye protection. Using safety equipment such as

a dust mask, non-skid safety shoes, a hard hat, or hearing protection whenever it is

needed will reduce the risk of personal injury.

POWDP8031 EN

▪Avoid accidental starts. Ensure the switch is in the off position before inserting the

plug. Carrying power tools with your finger on the switch or plugging in power tools

when the switch is in the on position makes accidents more likely.

▪Remove any adjusting keys or spanners before turning on the power tool. A spanner

or key left attached to a rotating part of the power tool may result in personal injury.

▪Do not reach out too far. Keep your feet firmly on the ground at all times. This will

enable you retain control over the power tool in unexpected situations.

▪Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and

gloves away from the power tool. Loose clothes, jewellery or long hair can become

entangled in the moving parts.

▪If there are devices for connecting dust extraction and collection facilities, please

ensure that they are attached and used correctly. Using such devices can reduce

dust-related hazards.

4.4 Power tool use and care

▪Do not expect the power tool to do more than it can. Use the correct power tool for

what you want to do. A power tool will achieve better results and be safer if used in

the context for which it was designed.

▪Do not use the power tool if the switch cannot turn it on and off. A power tool with a

broken switch is dangerous and must be repaired.

▪Disconnect the plug from the power source before making adjustments, changing

accessories, or storing power tools. Such preventive safety measures reduce the risk

of starting the power tool accidentally.

▪Store power tools, when not in use, out of the reach of children and do not allow

people who are not familiar with the power tool or these instructions to operate it.

Power tools are potentially dangerous in the hands of untrained users.

▪Maintain power tools. Check for misalignment or jammed moving parts, breakages or

any other feature that might affect the operation of the power tool. If it is damaged,

the power tool must be repaired. Many accidents are caused by using poorly

maintained power tools.

▪Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp

cutting edges are less likely to jam and are easier to control.

▪Use the power tool, accessories and cutting tools, etc., in accordance with these

instructions and in the manner intended for the particular type of power tool, taking

into account the working conditions and the work which needs to be done. Using a

power tool in ways for which it was not intended can lead to potentially hazardous

situations.

4.5 Service

▪Your power tool should be serviced by a qualified specialist using only standard

spare parts. This will ensure that it meets the required safety standards.

5 ADDITIONAL SAFETY INSTRUCTIONS FOR BATTERIES AND CHARGERS

Use only batteries and chargers applicable for this machine.

POWDP8031 EN

5.1 Batteries

▪Never attempt to open for any reason.

▪Do not store in locations where the temperature may exceed 40 °C.

▪Charge only at ambient temperatures between 4 °C and 40 °C.

▪When disposing of batteries, follow the instructions given in the section “Protecting

the environment”.

▪Do not cause short circuits. If connection is made between the positive (+) and

negative (-) terminal directly or via accidental contact with metallic objects, the battery

is short circuited and an intense current will flow causing heat generation which may

lead to casing rupture or fire.

▪Do not heat. If batteries are heated to above 100 °C, sealing and insulating

separators and other polymer components may be damaged resulting in electrolyte

leakage and/or internal short circuiting leading to heat generation causing rupture or

file. Moreover do not dispose of the batteries in fire, explosion and/or intense burning

may result.

▪Under extreme conditions, battery leakage may occur. When you notice liquid on the

battery, proceed as follows:

−Carefully wipe the liquid off using a cloth. Avoid skin contact.

−In case of skin or eye contact, follow the instructions below:

✓Immediately rinse with water. Neutralize with a mild acid such as lemon juice

or vinegar.

✓In case of eye contact, rinse abundantly with clean water for at least 10

minutes. Consult a physician.

Fire hazard! Avoid short-circuiting the contacts of a detached battery. Do

not incinerate the battery.

5.2 Chargers

▪Never attempt to charge non-rechargeable batteries.

▪Have defective cords replaced immediately.

▪Do not expose to water.

▪Do not open the charger.

▪Do not probe the charger.

▪The charger is intended for indoor use only.

6 SAFETY WARNING FOR WORK-LIGHT

▪This is not a toy; children are not permitted to use this led work light. This item is a

DIY product, all electronic parts are fixed already, any intention of opening the work-

light or changing the work-light’s design is prohibitive.

▪Do not attempt to replace or change the diode lights! If the protective glass is cracked

or broken, it must be replaced before the work light can be used again.

7 OPERATION

7.1 Charging the battery pack

The battery pack for this tool is supplied in a low charge condition to prevent possible

problems, therefore, you have to charge the battery before first use.

POWDP8031 EN

Note: Batteries will not reach full charge the first time they are charged.

Allow several cycles for the item to fully charge. The battery should only be

charged indoors.

After normal use, about 1 hour of charging time is required for the battery to be fully

charged.

The battery pack will become slightly warm while charging, this is normal and does not

indicate a problem.

Do not place the charger in an area of extreme heat or cold. Best is at normal room

temperature. When the battery becomes fully charged, unplug your charger from the

power supply and remove the battery pack from the charger.

Note:

▪Allow the battery pack to cool completely before charging.

▪Inspect the battery pack before charging, do not charge a cracked or leaking battery

pack.

7.1.1 Charging indication (Fig. 1a)

Connect the charger to the power outlet socket:

▪Solid green: ready to charge.

▪Flickering red: charging.

▪Solid green: charged.

▪Solid green and red: battery or charger damaged.

Note: If the battery does not fit properly, disconnect it and confirm that the

battery pack is the correct model for this charger as shown on the

specification chart. Do not charge any other battery pack or any battery

pack that does not securely fit the charger.

▪Frequently monitor the charger and battery pack while connected

▪Unplug the charger and disconnect it from the battery pack when finished.

▪Allow the battery pack to cool completely before using it.

▪Store the charger and battery pack indoors, out of reach of children.

NOTE: If battery is hot after continuous use in the tool, allow it to cool down

to room temperature before charging. This will extend the life of your

batteries.

NOTE: Remove battery pack from charger stand which use your thumb or

fingers, press the battery’s release button in and pull the battery pack off at

the same time.

7.2 Battery capacity indicator (Fig. 1b)

There are battery capacity indicators on the battery pack, you can check the capacity

status of the battery if you squeeze the button. Before using the machine, please press

switch trigger to check if the battery is full enough for properly working.

Those 3 LED might show the status of the capacity level of the battery:

3 LED’s are litt: Battery fully charged.

2 LED’s are litt: Battery 60% charged.

1 LED is litt: Battery almost discharged.

POWDP8031 EN

7.3 Inserting and removing the battery (Fig. 2-3)

▪Hold the tool with one hand and the battery pack (8) with the other.

▪To install: push and slide battery pack into battery port, make sure the release latch

on the rear side of the battery snaps into place and battery is secure before

beginning operation. (Fig. 2)

▪To remove: Press the battery release latch and pull the battery pack out at the same

time. (Fig. 3)

7.4 Adjusting the light’s direction (Fig. 4)

The work light head (1) can be turned 360°.

1 Loosen the adjustable knob (3).

2 Turn and adjust the work light head (1) to the desired position.

3 Retighten the adjustable knob (3).

7.5 ON/OFF button and power level button (Fig 5)

▪This portable work light is equipped with an ON/OFF button (9) and a power level

button (10), which can adjust the portable work light’s brightness.

▪If you want to adjust the brightness, repeatedly push the power level button until the

desired light brightness is reached.

WARNING: Do not stare directly at the light beam. Never aim the beam at

any person or an object other than the work piece.

Do not deliberately aim the beam at people and ensure that it is not directed towards the

eye of a person for longer than 0.25 s.

7.6 Hanging hook (Fig. 6)

There is a hanging hook (5) inside the product package. For use, add it to the bottom of

the bracket (2).

When you need to hang the work light, just turn it outwards and take it out; afterwards, put

it back into the initial position.

8 CLEANING AND MAINTENANCE

Clean the housing only with a damp cloth. Do not use any solvents! Dry thoroughly

afterwards. In order to maintain battery capacity, we recommend the battery to be

completely discharged every one month and fully recharged again .Only store with a fully

charged battery and top-up the charge from time to time if stored for a long time. Store in a

dry and frost-free place, the ambient temperature should not exceed 40 °C.

POWDP8031 EN

9 TECHNICAL DATA

Type

POWDP8031

Rated voltage

20 V DC

Wattage

10 W / 20 W / 30 W

Lumen

1,100 lm / 2,000 lm / 2,700 lm

Colour temperature

6400 K

Lifespan bulb

50,000h

Net weight

1.7 kg

Battery Working time

1h up to 18h

Working time position 1: 20 V - 2.0 Ah

5h45

Working time position 2: 20 V - 2.0 Ah

2h15

Working time position 3: 20 V - 2.0 Ah

Working time position 1: 40 V –2.5 Ah

12h30

Working time position 2: 40 V –2.5 Ah

Working time position 3: 40 V –2.5 Ah

2h30

Working time position 1: 40 V –4.0 Ah

18h45

Working time position 2: 40 V –4.0 Ah

7h30

Working time position 3: 40 V –4.0 Ah

3h45

10 WARRANTY

▪This product is warranted for a 36-month period effective from the date of purchase

by the first user.

▪This warranty covers all material or production flaws excluding : batteries, chargers,

defective parts subject to normal wear & tear such as bearings, brushes, cables, and

plugs, or accessories such as drills, drill bits, saw blades, etc. ; damage or defects

resulting from maltreatment, accidents or alterations; nor the cost of transportation.

▪Damage and/or defects resulting from inappropriate use also do not fall under the

warranty provisions.

▪We also disclaim all liability for any bodily injury resulting from inappropriate use of

the tool.

▪Repairs may only be carried out by an authorised customer service centre for

Powerplus tools.

▪You can always obtain more information at the number 00 32 3 292 92 90.

▪Any transportation costs shall always be borne by the customer, unless agreed

otherwise in writing.

▪At the same time, no claim can be made on the warranty if the damage of the device

is the result of negligent maintenance or overload.

POWDP8031 EN

▪Definitely excluded from the warranty is damage resulting from fluid permeation,

excessive dust penetration, intentional damage (on purpose or by gross

carelessness), inappropriate usage (use for purposes for which the device is not

suitable), incompetent usage (e.g. not following the instructions given in the manual),

inexpert assembly, lightning strike, erroneous net voltage. This list is not exhaustive.

▪Acceptance of claims under warranty can never lead to the prolongation of the

warranty period nor commencement of a new warranty period in case of a device

replacement.

▪Devices or parts which are replaced under the warranty therefore remain the

property of Varo NV.

▪We reserve the right to reject a claim whenever the purchase cannot be verified or

when it is clear that the product has not been properly maintained. (Clean ventilation

slots, carbon brushes serviced regularly, etc.).

▪Your purchase receipt must be kept as proof of date of purchase.

▪Your appliance must be returned undismantled to your dealer in an acceptably clean

state, (in its original blow-moulded case if applicable to the unit), accompanied by

proof of purchase.

▪Your tool must be charged at least 1x per month to ensure optimal operation of this

tool.

11 ENVIRONMENT

Should your appliance need replacement after extended use, do not

discard it with the household rubbish but dispose of it in an environmentally

safe way.

Waste produced by electrical machine items should not be handled like

normal household rubbish. Please recycle where recycle facilities exist.

Check with your Local Authority or retailer for recycling advice.

This product contains Li-ion. To preserve natural resources, please recycle or dispose of

batteries properly. Local, state or federal laws may prohibit disposal of Li-ion batteries in

ordinary trash. Consult your local waste authority for information regarding available

recycling and/or disposal options.

Table des matières

Autres manuels Powerplus Lampe de travail

Powerplus

Powerplus POWX0090LI Manuel utilisateur

Manuels Lampe de travail populaires d'autres marques

ANSMANN

ANSMANN POWERLIGHT 5.1 Manuel utilisateur

RTRMAX

RTRMAX RTX1868 Manuel utilisateur

FeinTech

FeinTech LAL00220 Manuel utilisateur

Bunker Hill Security

Bunker Hill Security 64735 Manuel utilisateur

Goobay

Goobay 30450 Manuel utilisateur

REV Ritter

REV Ritter SPOT Manuel utilisateur

Ignition

Ignition Stagepix Line 100 IP Manuel utilisateur

SCANGRIP

SCANGRIP DUO CONNECT Manuel utilisateur

Bosch

Bosch GLI 18 V Manuel utilisateur

Bayco

Bayco SL-1514 Manuel utilisateur

EUFAB

EUFAB SMD LED 8+1 Manuel utilisateur

DeWalt

DeWalt DCL510 Manuel utilisateur

PowerSmith

PowerSmith PWLD080T Manuel utilisateur

MaxLite

MaxLite 73683 Manuel utilisateur

Heitronic

Heitronic Trend 27867 Manuel utilisateur

Monzana

Monzana Gore MZCL10 Manuel utilisateur

EINHELL

EINHELL TE-CL 18/2000 LiAC Manuel utilisateur

Bayco

Bayco NIGHTSTICK Dual-Light Xtreme Lumens... Manuel utilisateur