POS-X XR-200 Manuel du propriétaire
XR-200
MINI DOT IMPACT PRINTER
PRODUCT SPECIFICATION
DATE : MAY 3, 2004
MANUAL REVISION 2.0
Page 1
Features
Dip Switch Configuration
Emulation mode, communications mode, baud rate, serial/parallel handshake, and head
printing characteristics are all configured through dip switch settings.
Data Buffer
The XR-200 printer has a built-in 48 Kilobyte I/O buffer allowing the host computer to free
itself after sending the print data.
Reliable communications
Centronics parallel or RS-232C compatible communications is built-in.
The XR-200 supports multiple baud rates, protocols, and handshaking on its parallel &
serial interfaces.
User controls
A power switch, a paper feed switch, power LED and Paper Low/Out error LED provide
ease of use.
Self Test Mode
A comprehensive self-test mode is available which describes the printer configuration and
dip switch setting information along with the version number of firmware installed.
Print orientation
The printer is capable of printing normal and upside down, the print orientation is selected
by software commands.
Selectable international characters
The XR-200 supports international characters selectable by software control.
Multiple Fonts/Sizes
Two different resident fonts are available for printing diversity. Each of these fonts can be
printed in normal, double wide, double height, and quadruple sizes. Both fonts and sizes
are software selected.
Bit image graphic
Two formats for bit mapped graphics are provided.
Error detection
The XR-200 can detect paper-out and paper-jam as well as paper near-end, controller
malfunction, and cover open status.
Peripheral Drive
Two cash drawer drivers are provided.
Page 2
Printer Specification
MODEL XR-200
PRINT METHOD 9-pin serial impact dot matrix
PRINT DIRECTION Bi-directional (with logical seeking)
NO. OF COLUMNS Epson Mode : 42/35, 40/33
Other Modes : 40/32
FONT SIZE 7 x 9, 9 x 9 dots
LINE SPACING n/144 inch
PRINTING WIDTH 63.5mm (2.5” )
PRINT SPEED 4.0 lines/sec (at 40CPL)
INK RIBBON EPSON, ERC-23 ERC-38 compatible
Black or Purple, Black/Red
PAPER Media Roll Paper
Width 76.2mm (3.0” )
Diameter 76mm (3.0” ) max.
Copies 3-ply max. (0.2mm or 0.008” thick)
DATA BUFFER 48K bytes
CASH DRAWER DRIVER 2 circuits (24V, 1A max)
INTERFACE RS-232C Serial (25Pin)
RS-232C Serial (9Pin)
Parallel (25Pin) or
Centronics Parallel (36Pin)
EMULATION Epson TM-U200, Citizen iDP-3540
Star SP200, Verifone P900
POWER SUPPLY Type External Adaptor
Input 120VAC, 230VAC
Output 24VDC X 2.5A
OPERATING CONDITION 5°C to 40°C, 10% to 80% RH
STORAGE CONDITION -20°C to 60°C, 5% to 95% RH
RELIABILITY MCBF 5 million lines
Printhead 150 million characters
DIMENSIONS Cutter 174.8(W) X 218.5(D) X 132.2(H)mm
Non cutter 174.8(W) X 218.5(D) X 132.2(H)mm
WEIGHT Cutter 4.8 lbs
Non cutter 3.7 lbs
CERTIFICATIONS FCC, UL/cUL, CE
Page 3
Self Test
While pressing the paper feed switch for more than 10 seconds after the printer in
turned on, the self test mode is initiated. The printer self test includes a listing of
the current default settings, read and write test of internal RAM, checksum test of
internal program memory, loop back detection statement, a staggered dot line, a
few lines of rotating character set, and a diagnostic report. The printer then enters
into the On-Line mode.
Configuration Setup
When the paper FEED switch is pressed and released instantly as the power is
applied to the printer, the printer will print the current printer configuration settings
along with the DIP switch information. If the printer setup needs to be changed,
turn the Power Off before changing the setting.
The printer will be setup at the factory as follows;
Printer is setup as follows:
Model: XR-200
Firmware: Ver X.XX
Loopback: Not Detected(DSR)
Interface: Serial
Emulation: Epson TM-U200
CR Character: CR=CR only
Flow Control: DTR/DSR
Data Bits: 8 Bits
Parity: None
Baud Rate: 9600
CPL: 40/33 Char/Line
Two Color: Installed
Auto Cutter: Installed
Paper : Roll Type
Page 4
User Switches
Panel Switches
Paper Feed button : Pressing the PF button momentarily will advance the paper one
character line and pressing it continuously will cause a fast feed at 15 lines per second.
Power Switch
A Power switch located on the lower left side of the printer is used to turn the printer
on/off.
Indicators
This section explains the different patterns signaled by the two LED indicators located on
the top cover of the XR-200.
LED1 LED2
STATUS RED GREEN GREEN REMARKS
Power Off OFF OFF OFF Normal power is not supplied to the printer
Power On Flash OFF ON Normal power is supplied to the printer
On line OFF OFF ON Normal error-free mode
Paper low OFF ON ON Insert new paper roll
Cover open Flash OFF ON Close cover
Paper empty Flash OFF ON Insert new paper roll
Paper jam ON OFF OFF Impossible to recover
Test mode ON OFF ON Ignored Paper Low
Page 5
Command List
EMULATION EPSON TM-U200
Command Hex Code Description
HT <09>H Horizontal tab
LF <0A>H Print and line feed
CR <0D>H Carriage Return
DLE EOT <10>H<04>H<n> Real-time status transmission
DLE ENQ <10>H<05>H<n> Real-time request to printer
ESC SP <1B>H<20>H<n> Set right-side character spacing
ESC ! <1B>H<21>H<n> Set print mode
ESC % <1B>H<25>H<n>S Select/cancel user-defined character set
ESC & <1B>H<26>H Define user-defined characters
ESC * <1B>H<2A>H Select bit-image mode
ESC - <1B>H<2D><n> Turn on/off underline mode
ESC 2 <1B>H<32>H Select 1/6 inch line spacing
ESC 3 <1B>H<33>H<n> Set line spacing
ESC < <1B>H<3C>H Return home
ESC = <1B>H<3D>H<n> Select peripheral device
ESC ? <1B>H<3F>H<n> Cancel user-defined characters
ESC @ <1B>H<40>H Initialize printer
ESC D <1B>H<44>H<n> Set horizontal tab positions
ESC E <1B>H<45>H<n> Turn on/off emphasized mode
ESC G <1B>H<47>H<n> Turn on/off double-strike mode
ESC J <1B>H<4A>H<n> Print and feed paper
ESC R <1B>H<52>H<n> Select an international character set
ESC U <1B>H<55>H<n> Turns on/off unidirectional printing mode
ESC a <1B>H<61>H<n> Select justification
ESC c 4 <1B>H<63>H<34>H<n> Select paper sensor to stop printing
ESC c 5 <1B>H<63>H<35>H<n> Enable/disable panel button
ESC d <1B>H<64>H<n> Print and feed n lines
ESC p <1B>H<70>H Generate pulse
ESC t <1B>H<74>H<n> Select character code table
ESC { <1B>H<7B>H<n> Turn on/off upside-down printing mode
GS I <1D>H<49>H<n> Transmit printer ID
GS a <1D>H<61>H<n> Enable/disable Automatic Status Back
GS r <1D>H<72>H<n> Transmit status
Page 6
EMULATION CITIZEN iDP-3540
Command Hex Code Description
BEL <07>H Drive pulse setting command for 1st drawer
CAN <18>H Clear data in buffer
LF <0A>H Paper feed
FF <0C>H<n> Paper feed n lines
CR <0D>H Print command
SO <0E>H Select expanded character mode
SI <0F>H Select normal character mode
DC1 <11>H Initial set command
DC2 <12>H Inverted print mode
DC3 <13>H Red color print command
ESC BEL <1B>H<07>H<n> 1st drawer driver command
SUB <1A>H 2nd drawer driver command
ESC - <1B>H<2D>H<n> Select underline mode
ESC * <1B>H<2A>H<n> Graphic command
ESC 1 <1B>H<31>H Set 1/9 inch line feed
ESC 2 <1B>H<32>H<n> Set 2/9 inch line feed
ESC C <1B>H<43>H<n> Set page length
ESC N <1B>H<4E>H<n> n line skip perforation command
ESC O <1B>H<4F>H Cancel skip perforation command
ESC P <1B>H<50>H<n> Select full-cut / partial-cut
ESC f <1B>H<66>H Form feed
FS <1C>H 1st drawer drive command
Page 7
EMULATION VERIFONE 900
Command Hex Code Description
NUL <00>H Pad character
CAN <18>H Empty print buffer and cancel character attributes
LF <0A>H Print and feed one line
FF <0C>H Print data in buffer and eject paper to 1.2
CR <0D>H Line feed
DC2 <12>H Change ribbon color
RS <1E>H Set double width mode or
SO <0E>H Select high page mode
US <1F>H Set normal width mode or
SI <0F>H Select ASCII character set
ESC a <1B>H<61>H<n> Set line height to n dots
ESC b <1B>H<62>H<n> Eject paper n lines
ESC c <1B>H<63>H Reset printer to power-up state
ESC d <1B>H<64>H Request printer status
ESC e <1B>H<65>H<n> Set right margin
ESC f <1B>H<66>H<n> Select line attributes
ESC g <1B>H<67>H Activate graphic mode
ESC h <1B>H<68>H Select character set
ESC I <1B>H<69>H Printer identification
ESC x <1B>H<78>H Enter P900R emulation mode
FS <1C>H Enter P250 emulation mode
GS <1D>H Enter P200 emulation mode
Page 8
EMULATION STAR SP200
Command Hex Code Description
BEL <07>H Differed drive command “ A” for peripheral unit
(Default setting)
CAN <18>H Cancel print data in buffer
LF <0A>H Line feed
CR <0D>H Line feed (same as LF)
SO <0E>H Select expanded character mode
SI <0F>H Cancel expanded character mode
FS <1C>H Immediate drive command “ B” for peripheral unit
1
DC4 <14>H Cancel expanded character mode
ESC BEL
n1 n2
<1B>H<07>H<n1>
<n2>
Adjust drive pulse width for peripheral unit
(Default setting)
ESC @ <1B>H<40>H Initialize printer
ESC M <1B>H<4D>H Select 7 x 7 (Half dots) character size
(Default setting)
ESC R n <1B>H<52>H<n> Select international character set
ESC P <1B>H<50>H Select 9 x 7 (Half dots) character size
ESC W 1 <1B>H<57>H<31>
H<1B>H<57>H<1>
Select expanded character mode
ESC W 0 <1B>H<57>H<37>
H<1B>H<57>H<0>
Cancel expanded character mode
ESC a n <1B>H<61>H<n> Feed paper n lines
Page 9
Interface
The tables below describe the type of socket and the function of each pin.
<D-SUB 25 Female Serial Port> <D-SUB 25 Male Parallel Port>
<D-SUB Centronics Parallel Port> <D-SUB 9 Female Serial>
Table des matières
Autres manuels POS-X Imprimante
POS-X
POS-X XR210 Manuel utilisateur
POS-X
POS-X EVO-RP1-U Manuel utilisateur
POS-X
POS-X EVO-RP1 Manuel utilisateur
POS-X
POS-X XR210 Manuel utilisateur
POS-X
POS-X EVO-PK2-1AP Manuel utilisateur
POS-X
POS-X ION-PT2 Manuel utilisateur
POS-X
POS-X EVO-RP1-U Manuel utilisateur
POS-X
POS-X EVO HiSpeed Manuel utilisateur
POS-X
POS-X XR510 Manuel utilisateur
POS-X
POS-X ION THERMAL Manuel utilisateur
