Poniie TC-10A Manuel utilisateur

User Manual

Model No: TC-10A

Thank you for purchasing the Temperature Controller by Poniie. Please read

this manual carefully before using this product.

1. Safety Precautions

1.1 Ensure the product is used within the specification (Max. 10A).

1.2 Induction loads such as compressors, refrigerators, space

heaters, pumps may have a start-up amp of 2 to 7 times the

continuous rating. Overload start-up amp may cause damage or

shorten device’s lifespan.

1.3 Do not operate the controller near any high temperature, high

humidity, explosive or inflammable field.

1.4 Children are not allowed to operate the device. Keep children

away from the controller.

1.5 Do not use in salt water or corrosive water, the metal NTC probe

will be slowly damaged by salt water or acid-alkali water.

2. Overview

What is TC-10A?

TC-10A is an easy-to-use, safe and reliable dual relay output

temperature controller. It can be connected to both heating and cooling

loads at the same time to control temperature.

This unit can be used as over temperature protection or automatic

temperature control system for various tasks. Such as Sous-vide,

Terrarium Heat Control, Heat Mats, Germination, Fermentation and

Brewing.

Main features

•Pre-wired plug and play;

•Dual relay output for heating and cooling;

•Support reading with ℃ and ℉;

•Dual display windows, be able to display measured temperature

and set center temperature at the same time;

•Auto saving function with power-off memory;

•Calibration function;

•Compressor delay protection;

•High and low temperature alarm;

•Faulty sensor alarm

3. Specification

Temperature Control Range

-20.0 ~ 80.0℃

Temperature Resolution

0.1℃

Temperature Accuracy

±1.0 ℃(-20.0 ~ 70.0 ℃)

Input Power

100~125V, 50/60Hz

Maximum Output Load

10A, 100 ~ 125V (1200W @120V)

Buzzer Alarm

Low and High Temperature Alarm

Sensor Type

NTC sensor

Control Panel Cable Length

1.5m / 4.9ft

Input Power Cable Length

1.7m / 5.6ft

Sensor Length

2.0m / 6.6ft

Ambient Temperature

-20.0 ~ 55.0 ℃

Ambient Humidity

20~85% (No Condensate)

4. Key Operation Instruction

4.1 Dual display.

The upper window, in working mode, displays current environment

temperature and working status; in setting mode, displays menu code.

ON: Refrigeration is in working state;

FLASHING: Refrigeration is in compressor delay time.

ON: Heating is in working state;

OFF: Not working.

The lower window, in working mode, displays shutdown

temperature point (TS) for both heating and cooling (It can be taken

as the central temperature point); in setting mode, displays setting value

of menu codes.

When controller working normally, press “▼” key, the setting Low

Temperature (TL) point is displayed; press “▲” key, the setting High

Temperature (TH) point is displayed. The screen will auto return to

normal display after 2 seconds.

4.2 How to set parameters?

Basic Setting Mode: Press “SET”key to enter the basic setting mode,

You only need to set three temperature points TL, TS and TH to set a

suitable control range. TL/TS/TH relationship is as follows:

After setting, hold down the “SET”button 3 seconds or leave it with no

operation 15 seconds, the system will save the parameter changes and

return to the working mode.

Note: You can only set the basic Settings, leaving the advanced

Settings unchanged, and only change the advanced Settings parameters

if necessary.

Advanced Setting Mode: Press & hold down “SET”key 3 seconds to

enter the advanced setting mode. You are able to set AL (Low Alarm

Temperature point), AH (High Alarm Temperature point), PT

(Compressor Protection Time), CF (℃/℉Display setting) and CA

(Calibration function) parameters. After settings, press & hold down

“SET”key 3 seconds or leave it with no operation 15 seconds to save

parameter changes and return to working mode.

User Tips: 1)Under setting mode, press “SET”key to cycle through all

parameter codes, press “▼”& “▲” to adjust the setting values below.

2)Press & hold down “▼” & “▲” can adjust setting value more quickly.

Cooling

Heating

5. Setup Flow Chart

Basic Setting Mode

Advanced Setting Mode

Short press “SET” Press & hold “SET” for 3s

SET 3S

SET

23.0℃

SET

-20.0℃

SET

70.0℃

SET

2min

℃

0℃

25.0℃

27.0℃

SET

Working Normally

SET

6. Menu Instruction

ode

Function

Setting

ange

efault

Setting

Remarks

Low

Temperature Point

20.0~80.0℃

23.0℃

6.1

Shutdown

Temperature Point

20.0~80.0℃

25.0℃

High

Temperature Point

20.0~80.0℃

27.0℃

Low Alarm

Temperature

20.0~(TL-0.5)℃

20.0℃

6.2

High

Alarm Temperature

(TH+0.5)

~80.0℃

70.0℃

Compressor Delay

0~1

0min

2min

6.3

℃/℉ Display

℃/℉

℃

6.4

Temperature Calibration

20.0~20.0℃

℃

6.5

6.1 Temperature Control Range Setting (TL, TS, TH)

This controller has a heating and cooling control outlets. However,

you can only use the heating or cooling side for your project.

When measured temperature ≤ TL, system enter heating state, the

heating outlet relay starts to work; when it heats up to shutdown point

(TS), the heating relay stops.

When measured temperature ≥ TH, system enter cooling state, the

cooling outlet relaystarts to work; when it cools to shutdown point

(TS), the cooling relay stops.

In case the time interval between two cooling action is less than PT,

please refer to 6.3.

Caution: Please be aware of the temperature surge risk when setting a

large temperature gap between TL--TS /TS--TH. Recommend to set

the gap smaller than 10 degrees. The tighter gap the more stable real

temperature.

Note: Please check and test your setting every time before leaving

controller to a long-term running.

6.2 Temperature Alarm Setting (AL, AH)

When measured temperature ≤ AL, low temperature alarm will be

triggered, buzzer will alarm until temperature＞AL or any key is

pressed.

When measured temperature ≥ AH, high temperature alarm will be

triggered, buzzer will alarm until temperature＜AH or any key is

pressed.

Note: If you set the AL ≥ TL, then the real low temperature alarm

point is TL-0.5℃. If you set the AH ≤ TH, the real high alarm point is

TH+0.5℃.

6.3 Compressor Protection Time (PT)

Under cooling mode, compressor protection will keep the refrigeration

off between cycles to protect your compressor. That means

compressor won't start refrigeration immediately, but waiting for a

delay time if it falls into the PT time frame. Delay time will be

calculated right after the moment refrigeration stops.

6.4 Display in Celsius or Fahrenheit degree (CF)

Users can select display in Celsius or Fahrenheit degree unit according

to their needs. Default setting is ℃.

Note: when you select Fahrenheit unit, the display for over 100℉ will

be a whole number, resolution becomes 1℉.

6.5 Temperature Calibration (CA)

When there is a deviation between measured temperature and actual

temperature, you can use the calibration function to align the

measured temperature and actual temperature. The corrected

temperature equals to temperature before calibration plus corrected

value (corrected value can be positive, 0 or negative value)

7. Error Description

1) If LED displays flashing code AL or AH, please kindly check your

AL or AH setting in advanced setting mode. Buzzer will alarm until

temperature fall into setting range or any key is pressed (the flash

indication will continue unless the temperature goes into normal range).

2) If LED displays code ER, then sensor is in short circuit or open loop.

Please contact Poniie customer service (support@poniie.com) for

solution.

Table des matières

Autres manuels Poniie Régulateurs de température

Poniie

Poniie TC-15A Manuel utilisateur

Manuels Régulateurs de température populaires d'autres marques

Swegon

Swegon LUNAd MB Manuel utilisateur

Lucky Reptile

Lucky Reptile Thermo Control II Manuel utilisateur

SENSORMETRIX

SENSORMETRIX Argon 100 Manuel utilisateur

Fuji Electric

Fuji Electric PXE4 Manuel utilisateur

Yuyao gongyi

Yuyao gongyi XMT-808 series Manuel utilisateur

Selec

Selec TC544C Manuel utilisateur

P.W. KEY

P.W. KEY rt-208gt Manuel utilisateur

Future Design

Future Design FDC-9200 Manuel utilisateur

BH Thermal

BH Thermal BriskONE Manuel utilisateur

Omron

Omron E5EX-H Manuel utilisateur

West Control Solutions

West Control Solutions KS 45 Guide de démarrage rapide

MCS

MCS RITC-15B Manuel utilisateur

SMC Networks

SMC Networks Thermo-con INR-244-639 Manuel utilisateur

eltherm

eltherm Ex-TC It Series Manuel utilisateur

Omron

Omron C200H-TV Series Manuel utilisateur

industrie technik

industrie technik CA1 Manuel utilisateur

KRAL

KRAL EET 32 Manuel utilisateur

dixell

dixell XR420C Schéma de câblage