Polycom KIRK Wireless Server 600v3 KWS600v3 Manuel utilisateur
Part No. 14168600, Ed.2
April 3, 2008
Polycom®KWS600v3 Configuration Guide
(SIP Protocol)
2
14168600, Ed.2
Copyright © Polycom, Inc.
All Rights Reserved
Catalog No. 14168600
Version 2
Proprietary and Confidential
The information contained herein is the sole intellectual property of Polycom, Inc. No distribution,
reproduction or unauthorized use of these materials is permitted without the expressed written consent of
Polycom, Inc. Information contained herein is subject to change without notice and does not represent
commitment of any type on the part of Polycom, Inc. Polycom and Accord are registered trademarks of
Polycom, Inc.
Notice
While reasonable effort was made to ensure that the information in this document was complete and
accurate at the time of printing, Polycom, Inc., cannot assume responsibility for any errors. Changes and/
or corrections to the information contained in this document may be incorporated into future issues.
Contents 3
KWS600v3 Protocol Configuration Guide (SIP Protocol)
Contents
Chapter 1 Preface.......................................................................................................... 5
1.1 Before You Begin ........................................................................................................ 5
1.2 Chapter Overview ....................................................................................................... 5
1.3 Related Documentation .............................................................................................. 5
Chapter 2 SIP Specific Configuration ......................................................................... 7
2.1 Configuring DECT Master .......................................................................................... 7
2.2 Configuring DECT System ......................................................................................... 8
2.3 Configuring Call Waiting ............................................................................................. 8
4
14168600, Ed.2
5
KWS600v3 Configuration Guide (SIP Protocol)
Chapter 1 Preface
This guide describes the specific configuration of a KIRK Wireless Server 600v3
(KWS600v3) when using SIP Protocol. The guide is intended for qualified technicians
who will install, register and configure a KWS600v3 in a SIP environment. To qualify to
install the KWS600v3 Solution, you must have successfully completed the KWS600v3
technical training.
The user guide also provides you with information about:
• KIRK Wireless Server 600v3
• Web based Adminstration Page of the KIRK Wireless Server 600v3
1.1 Before You Begin
This guide assumes the following:
• that users have a working knowledge of the call handlers operation
• that the call handler is installed and initialized and is working correctly
• that users have a working knowledge of the KIRK Wireless Server 600v3
• that users have a working knowledge of the web based Administration Page
• that users are familiar with the KIRK Wireless Server 600v3 Installation and
Configuration Guide
1.2 Chapter Overview
1
1.3 Related Documentation
For further information about the system components not covered by this manual, refer
to the following documentation:
Where is it? What is it about? When to use it?
Chapter 2 SIP Specific Configuration To learn how to configure a KWS600v3 in a SIP
environment.
Subject Documentation
KIRK Wireless Server 600v3 Installation and Configuration Guide
6Preface
14168600, Ed.2
7
KWS600v3
Chapter 2 SIP Specific Configuration
This section describes how to configure the KIRK Wireless Server 600v3 when using SIP
Protocol. It only describes specific configuration procedures in connection with the SIP
Protocol.
For detailed information about installing and configuring the KWS600v3 in general, refer
to the KIRK Wireless Server 600v3 Installation and Configuration Guide.
For information about accessing the web based Administration Page of the KIRK
Wireless Server 600v3, refer to the KIRK Wireless Server 600v3 Installation and
Configuration Guide.
This section contains information about:
•“Configuring DECT Master” on page 7
•“Configuring DECT System” on page 8
•“Configuring Call Waiting” on page 8
2.1 Configuring DECT Master
When configuring the KWS600v3 in a SIP environment it is necessary to type a
gatekeeper ID.
1Under the Configuration menu, click DECT, and then click Master.
Figure 1 Adm. Page: Configuration/DECT/Master page - SIP Protocol
2In the GK-Id field, type a domain name.
An example of a domain name could be: sip:kirk323.kirktelecom.com.net:5060.
Contact your system administrator for more information.
3Click OK.
4Click Reset (under Administration menu) to save your configuration.
8 SIP Specific Configuration
14168600, Ed.2
2.2 Configuring DECT System
When configuring the KWS600v3 in a SIP environment it is necessary to enable the check
boxes; Enbloc Dialing and DTMF through RTP channel.
1Under the Configuration menu, click DECT, and then click System.
Figure 2 Adm. Page: Configuration/DECT/System page - SIP Protocol
2Select the Enbloc Dialing check box.
The Enbloc Dialing check box has to be enabled in a SIP configuration in order for
the handset to collect all digits, before passing them on to a call handler for routing.
3Select the DTMF check box.
The DTMF check box has to be enabled in a SIP configuration if DTMF tones are
needed (optional).
4Click OK.
5Click Reset (under Administration menu) to save your configuration.
2.3 Configuring Call Waiting
To enable the Call Waiting feature in the system, you must do the following:
SIP Specific Configuration 9
KWS600v3 Protocol Configuration Guide (SIP Protocol)
1Under the Configuration menu, click DECT, and then click Features.
Figure 3 Adm. Page: Configuration/DECT/Features page - SIP Protocol
2Select the Enable check box to enable the Call Waiting feature.
3Click OK.
4Click reset required.
A window appear.
5Click OK.
The Call Waiting feature is now enabled in the system. For the feature to be used, it
must be activated on each handset by pressing *43# on the handset.
10 SIP Specific Configuration
14168600, Ed.2
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels Polycom Serveur
Polycom
Polycom RSS 2000 Manuel utilisateur
Polycom
Polycom KIRK 8000 Manuel utilisateur
Polycom
Polycom KIRK Manuel utilisateur
Polycom
Polycom KIRK 8000 Manuel utilisateur
Polycom
Polycom PDS 725-78600-002A2 Manuel utilisateur
Polycom
Polycom Realpresence collaboration server 1500 Guide de référence rapide
Polycom
Polycom DOC2560C Manuel utilisateur
Polycom
Polycom V2IU4300T Manuel utilisateur
Polycom
Polycom RMX 1500 Fiche technique
Polycom
Polycom KIRK 14117800 Manuel de l'opérateur
Polycom
Polycom Spectralink 8000 SVP100 Mode d’emploi
Polycom
Polycom RSS 2000 Manuel utilisateur
Polycom
Polycom RealPresence RMX 1800 Fiche technique
Polycom
Polycom DOC2564A Manuel utilisateur
Polycom
Polycom ReadiManagerLX100 Guide de démarrage rapide
Polycom
Polycom SpectraLink 1725-36033-001 Mode d’emploi
Polycom
Polycom KIRK Wireless Server 6000 Manuel de l'opérateur
Polycom
Polycom V2IU6400-S Manuel utilisateur
Polycom
Polycom SpectraLink 1725-36031-001 Mode d’emploi
Polycom
Polycom Real-Time Media Conferencing Platform RMX... Fiche technique
