Polycom DOC2564A Manuel utilisateur

RMX

4000 Installation &

Configuration Guide

General Safety Precautions

Follow these rules to ensure general safety:

• Keep the area around the Polycom RMX®4000 unit clean and free

of clutter and well ventilated.

• Decide on a suitable location for the equipment rack that will hold

the RMX, ensuring that it is near a grounded power outlet.

• Ensure that the leveling jacks on the bottom of the rack are fully

extended to the floor with the full weight of the rack resting on

them. Always make sure the rack is stable before extending a

component from the rack.

• In a single rack installation, attach stabilizers to the rack. In

multiple rack installations, the racks should be coupled together.

• Use a regulating uninterruptable power supply (UPS) to protect the

RMX from power surges and voltage spikes, and to keep it

operating in the event of a power failure.

• Allow the power supply units to cool before touching them.

• Always keep the rack’s trays and board’s closed when not

servicing, to maintain proper cooling.

• Use only the power cords supplied with the system.

• Each power cord should only be connected to a power outlet that

has a protective ground contact.

For all safety requirements and precautions, see the RMX 4000

Hardware Guide, "Safety Requirements” on page 1-6.

Preparations

Obtain the following information from your network administrator:

• IP addresses, Subnet Mask and Default Gateway IP address

(optional) for the RMX control unit and RMX Shelf Management.

• IP addresses for the RMX Signaling Host and Media cards.

• Gatekeeper IP address.

• SIP server IP address, if applicable.

If ISDN/PSTN is installed in your conferencing environment, obtain the

following information from your ISDN/PSTN Service Provider:

• Switch Type, Line Coding and Framing, Numbering Plan and

Numbering Type.

• Dial-in number range.

Unpacking the RMX

1When you receive the RMX packing case, inspect the equipment for

damage and verify that the components match the packing slip.

2The RMX is shipped in a packing case with Stratocell® packaging,

and the top cover must be unlocked and lifted.

3Remove the boxes that are placed on the top Stratocell® and the top

Stratocell® and open the anti-static plastic bag wrapping the RMX.

4Holding the handle on each side, lift the RMX from the box, and

place it on a flat surface or in a rack. Remove any packaging

material prior to positioning the RMX.

If the RMX is connected to the public ISDN Network, an external

CSU or similar equipment is needed.

Attention:

Two people are required to lift the MCU out of the box and when

installing it in a rack.

Write down the RMX’s serial number that is on a sticker on the back

of the unit. It will be needed for product registration later in the

installation process.

Management Network Configuration on the

USB Key

The system is shipped with the following default IP addresses:

• Control unit IP address – 192.168.1.254

• Shelf Management IP Address – 192.168.1.252

• Control unit subnet mask – 255.255.255.0

• Default Router IP Address – 192.168.1.1

When the RMX is installed for the first time, you must change the

default IP addresses to your local network settings. This can be done by

modifying the default settings in the USB key shipped with the unit

using the LAN Configuration Utility and uploading them to the RMX.

1Take the USB Key from the Installation Accessories kit and insert it

into a PC.

2Double-click LanConfigUtility.exe to start the utility.

3Modify the required network parameters in the utility’s dialog box

using the information supplied by your network administrator.

4Click OK.

5Remove the USB Key from the PC.

The USB Key is required for first entry power-up of the RMX.

Installing the RMX

To install the RMX 4000 in a 19”rack using chassis runners:

1Install chassis runners supplied by Polycom, in the rack.

2Mount the RMX 4000 on top of the rack brackets.

For a detailed description of the safety requirements and

precautions and the installation of the RMX 4000 as a standalone,

mounted in a 23” rack, or reverse mounting the RMX 4000 on a 19”

rack, see the RMX 4000 Hardware Guide.

To connect the RMX 4000 to the DC power, see the RMX 4000

Hardware Guide, "Connecting the RMX 4000 to -48DC SELV

Power” on page 1-17.

3Fasten the RMX to the rack with screws through the eight holes in

the RMX’s front mounting brackets.

Connecting the cables to the RMX 4000

Connect the following cables to the RMX 4000 rear panel:

•For AC Power Supply connections: Insert a power cable in each of

the three AC Power Entry Modules (PEM’s).

For DC Power connections, see the RMX 4000 Hardware Guide.

•OntheRTM IP-4000:

—Connect the Management Network cable to LAN 2.

—Connect the Signalling cable to LAN 3.

—Connect the Shelf Management cable to LAN 6.

• For each installed RTM LAN - Connect the LAN cable to LAN 2.

• For each installed RTM ISDN:

—Connect the E1/T1 cables to their PRI Ports.

—Connect the LAN cable to LAN 1.

First Entry Power-up

1Insert the USB Key with the modified IP addresses in the USB port

on the back panel.

2Turn ON the power by pressing on the power switch located on the

rear panel of the RMX.

The parameters in the lan.cfg file are uploaded from the USB Key to

the RMX’s memory and applied during the power-up sequence.

System power-up sequence may take up to five minutes.

The size of the protective earthing conductor & cable should be a

minimum of 10AWG.

•LAN 4, LAN 5 and the Serial ports are only for debugging and

not for customer use.

•Do not remove the protective plastic caps from LAN 1, LAN 4

and LAN 5 ports.

During the first-time power-up the red ERR LED on the RMX’s

front panel remains ON until both the Management and IP

Network Services have been defined.

When the RMX's configuration is completed (including the

Management and IP Network Services), and if there are no System

Errors, the green RDY LED on the CNTL module (on the RMX’s

front panel) turns ON.

3Remove the USB key.

Product Registration and Activation Key Retrieval

Before starting the initial configuration process, register the RMX at the

Polycom Resource Center website and download the product activation

key file to the computer you will use for the configuration:

1Using a Web browser, connect to http://portal.polycom.com.

2Login with your Email Address and Password or register as a new

user.

3Select the Product Registration link.

4Follow the on-screen instructions for Product Registration and

Product Activation.

5Write down the Product Activation Key number or copy it for later

use.

Connecting to the MCU

1Start the RMX Web Client application on the workstation by

entering in the browser’s address line the IP Address of the control

unit as defined in the USB key in the format:

http://<Control Unit IP Address> and pressing Enter.

2In the RMX Web Client Welcome Screen, enter the default Username

(POLYCOM)and Password (POLYCOM) and click Login.

The RMX Web Client opens.

An MCU State indicator displays a progress indicator showing the

time remaining until the system start-up is complete.

The Product Activation dialog box is displayed with the serial

number filled in.

3In the Activation Key field, enter or paste the Product Activation Key

retrieved earlier and click OK.

If you do not have an Activation Key, click the Polycom Resource

Center button to access the Service & Support page of the Polycom

website.

The system prompts with a System Reset dialog box.

4In the System Reset dialog box, click No.

As no Default IP Network Service is defined, the system

automatically starts the Fast Configuration Wizard.

The Fast Configuration Wizard is displayed.

Configuring the IP Network Service

The Fast Configuration Wizard enables you to configure the Default IP

Service. It starts automatically if no Default IP Network Service is defined.

This happens during First Time Power-up,before the service has been

defined or if the Default IP Service has been deleted, followed by an RMX

reset.

The IP Management Service tab in the Fast Configuration Wizard is

enabled only if the default Management IP addresses were not

modified.

1In the Fast Configuration Wizard - IP dialog box, define the following

parameters:

On the RMX 4000, IPv4 is the default protocol for setting the Network

Service in the Fast Configuration Wizard.

Field Description

IP Service

Name Use the default name (Default IP Service) or enter a name

using up to 20 characters.

Note: This field is displayed in all dialog boxes.

2Click Next.

3In the Fast Configuration Wizard - Routes dialog box, enter the IP

address of the default router.

4Click Next.

5Enter the required DNS information in the dialog box.

Signaling Host

IP Address Enter the IP address of the Central Signaling host. This is

the address used by endpoints for dialing in to the MCU.

Media Card 1/2/

3/4 IP Address Enter the IP address(es) of the media card (s): MPM+ /

MPMx 1, MPM+/MPMx 2, MPM+/MPMx 3 and MPM+/

MPMx 4 (if installed), as provided by the network

administrator. Endpoints connect to conferences and

transmit call media (video, voice and content) via these

addresses.

Subnet Mask Enter the subnet mask of the MCU.

Default value: 255.255.255.0.

If Secured Communication is required on the RMX: complete the

Fast Configuration Wizard, Login, install the Certificate and then

enable the Secured Communication Mode.

Field Description

MCU Host Name Enter the name of the MCU on the network.

Default name is RMX

DNS Select:

•Off – if DNS servers are not used in the

network.

•Specify – to enter the IP addresses of the DNS

servers.

Note: The IP address fields are enabled only if

Specify is selected.

Field Description

6Click the Next button.

7In the Fast Configuration Wizard - Environment dialog box, select the

IP Network Type: H.323,SIP or H.323 &SIP.

8Click Next.

9If you selected SIP go to Step 13.

10 In the Fast Configuration Wizard - Gatekeeper dialog box, enter the

required information:

Names

Automatically to

DNS Server

Select this option to automatically register the

MCU Signaling Host and Shelf Management with

the DNS server.

Local Domain

Name Enter the name of the domain where the MCU is

installed.

Primary DNS

Server IP Address The static IP addresses of the primary DNS server.

Field Description

Gatekeeper Select Specify to enable configuration of the

gatekeeper IP address.

When Off is selected, all gatekeeper options are

disabled.

Primary Gatekeeper

IP Address or

Name Enter either the gatekeeper’s host name (if a DNS

Server is used) or IP address.

MCU Prefix in

Gatekeeper Enter the string with which the MCU registers itself

with the gatekeeper.

The gatekeeper uses this string to identify the MCU

when forwarding calls to it.

H.323 endpoints use this number as the first part of

their dial-in string when dialing the MCU.

Field Description

11 Click Next.

12 If you selected H.323 only go to Step 15.

13 In the Fast Configuration Wizard - SIP dialog box, enter the following

information:

Aliases

Alias The alias by which the RMX’s Control Unit is identified

within the network. Up to five aliases can be defined

for each RMX.

Note: When a gatekeeper is specified, at least one

prefix or alias must be entered in the table.

Type Select the type that defines the format in which the

card alias is sent to the gatekeeper.

•H.323 ID (alphanumeric ID)

•E.164 (0-9, * #)

•URL ID (URL style address)

•Transport ID (IP address: port number)

•Email ID (email address format)

•Party Number (identical to the E.164 format)

Note: Although all alias types are supported (with

H.323 and E.164 being the most common), the type to

be used depends on your gatekeeper’s capabilities.

Field Description

SIP Server Select:

•Specify – to manually configure SIP servers.

•Off – if SIP servers are not present in the network.

SIP Server IP

Address Enter either the IP address of the preferred SIP server

or its host name (if a DNS server is used).

Field Description

14 Click the Next button.

15 Enter the required Security information in the dialog box.

16 Click the Save & Continue button.

During the initial RMX setup, if the system detects the presence of the

RTM ISDN card, the ISDN /PSTN Network Service definition screens of

the Fast Configuration Wizard are enabled.

If there is no RTM ISDN card in the RMX or if you do not want to define

an ISDN/PSTN Network Service, go to Step 32.

Transport Type Select the protocol that is used for signaling between

the MCU and the SIP Server or the endpoints

according to the protocol supported by the SIP Server:

UDP – Select this option to use UDP for signaling.

TCP – Select this option to use TCP for signaling.

TLS – The Signaling Host listens on secured port

5061 only and all outgoing connections are

established on secured connections. Calls from SIP

clients or servers to non secured ports are rejected.

The supported security protocols are: TLS 1.0, SSL

2.0 and SSL 3.0.

Field Description

Authentication

User Name Enter the conference, Entry Queue or Meeting Room

name as registered with the proxy.

This field can contain up to 20 ASCII characters.

Authentication

Password Enter the conference, Entry Queue or Meeting Room

password as defined in the proxy.

This field can contain up to 20 ASCII characters.

Field Description

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Polycom Serveur

Polycom

Polycom DOC2562A Manuel utilisateur

Polycom

Polycom KIRK 14117800 Manuel de l'opérateur

Polycom

Polycom realpresence 1800 Instructions d'installation

Polycom

Polycom realpresence 1800 Mode d’emploi

Polycom

Polycom Realpresence collaboration server 1500 Manuel de service

Polycom

Polycom DOC2558B Instructions d'installation

Polycom

Polycom RSS 2000 Manuel utilisateur

Polycom

Polycom ReadiManagerSE200 Manuel utilisateur

Polycom

Polycom KIRK Manuel utilisateur

Polycom

Polycom Collaboration Server (RMX) 1800 Instructions d'installation

Polycom

Polycom Spectralink 8000 SVP100 Mode d’emploi

Polycom

Polycom SpectraLink 8000 System Mode d’emploi

Polycom

Polycom RealPresence 4000 Instructions d'installation

Polycom

Polycom VVX 1500 Series Manuel utilisateur

Polycom

Polycom RMX 2000 Fiche technique

Polycom

Polycom RealPresence RMX 1500 Manuel utilisateur

Polycom

Polycom RSS 2000 V1.0 Manuel utilisateur

Polycom

Polycom V2IU6400-S Manuel utilisateur

Polycom

Polycom KIRK 8000 Manuel utilisateur

Polycom

Polycom Collaboration Server (RMX) 2000 Instructions d'installation

Polycom

Polycom realpresence 1800 Manuel utilisateur

Polycom

Polycom DOC2558C Instructions d'installation

Polycom

Polycom DOC2232A Manuel utilisateur

Polycom

Polycom KIRK 300 Manuel utilisateur

Manuels Serveur populaires d'autres marques

HP AlphaServer ES47 Manuel utilisateur

Dell

Dell PowerEdge R410 Manuel utilisateur

PowerNAS

PowerNAS CMA Manuel utilisateur

Supero

Supero FatTwin F617R3-FT Manuel utilisateur

MSI

MSI P1-109N-L70 Manuel utilisateur

Dell

Dell PowerEdge XE9640 Manuel

Dell

Dell PS4100 Instructions de montage

EtroVISION

EtroVISION EV3151 Manuel utilisateur

NEC

NEC Express5800/T110j Manuel utilisateur

HP ProLiant Gen9 Manuel utilisateur

Compaq

Compaq ProLiant 3000 Manuel

Dell

Dell PowerEdge 3YPMN Manuel utilisateur

iRobo

iRobo IPC2U Manuel utilisateur

Nortel

Nortel 1000 Con?guration guide Manuel utilisateur

Asus

Asus AP7500 Manuel d'utilisation et d'entretien

Avid Technology

Avid Technology AirSpeed 5000 Manuel utilisateur

HP Integrity rx2600 Guide d'installation

Milestone

Milestone Husky IVO 350T Manuel utilisateur